Related
Good
Searching the internet I came here to change the rom of my phone, use the hard reset and did not have any problem in the process, then asks me to restart the phone, restarted, and when a screen turns white and does not come out of it, no more than anything.
I'm a little desperate now, I know there is a high-value mobile but it cost me to raise the money to buy it, I hope you have a solution and can help me.
From already thank you very much
PS: sorry for my bad English, I am South American
Sounds like you flashed and incompatable ROM or didn't use hard_spl either way go over to the htc official website - click support find your device and it will list some stock ROMs download an official ROM using the S/N from underneath the battery - Make sure the battery has plenty of charge - plug into your PC and load the stock htc ROM file this should take you through all the standard ROM flash info and will then flash the stock ROM onto your device. Hopefully this will flash back to stock for you and no more white screen.
Good luck and let us know how it went
warlordxxx said:
Sounds like you flashed and incompatable ROM or didn't use hard_spl either way go over to the htc official website - click support find your device and it will list some stock ROMs download an official ROM using the S/N from underneath the battery - Make sure the battery has plenty of charge - plug into your PC and load the stock htc ROM file this should take you through all the standard ROM flash info and will then flash the stock ROM onto your device. Hopefully this will flash back to stock for you and no more white screen.
Good luck and let us know how it went
Click to expand...
Click to collapse
good
I think that what you say is only for original phone htc diamond 2, since according to official rom I read are for the real htc diamond 2.
The mine is not original, as it says is a Chinese clone t5388i, please follow the screen in white, would greatly appreciate if someone helps me out of this problem is quite afflicted.
Again sorry for my bad English
sorry missed the clone bit on your topic . I don't have a clone myself so no ideas if the hard reset works. Might be a good idea to post which ROM you flashed to it
good day
the mobile screen just stayed white and does not know how I can flash now, there will be someone who has been the same and have a solution? I appreciate it, I would be very helpful.
Greetings
HTC_NEW, please check this topic. It's dedicated to the clone phones (except the T5388++ who has it's own topic)
There is a tool called k3AID available who could help you. It's posted in that topic about 50 posts ago. I have a copy if you need it.
There is also another possibility to do a blind flash. This means the screen is not working but the phone can still be flashed. First thing is get the correct firmware for your phone because each time you flash the phone can get bricked / defect.
If my feedback helps you to solve your problem, please give me a thanks on the post.
Eer said:
HTC_NEW, please check this topic. It's dedicated to the clone phones (except the T5388++ who has it's own topic)
There is a tool called k3AID available who could help you. It's posted in that topic about 50 posts ago. I have a copy if you need it.
There is also another possibility to do a blind flash. This means the screen is not working but the phone can still be flashed. First thing is get the correct firmware for your phone because each time you flash the phone can get bricked / defect.
If my feedback helps you to solve your problem, please give me a thanks on the post.
Click to expand...
Click to collapse
hello friend
Reading that topic and searching for the tool by
internet gave me great hope, many users
have managed to solve the same problem, as no
I have a good English I can not understand how it's done
the process, did you guys could help me with a small
tutorial on how to fix my phone with that program?
I enter the program is that you give to download mode and
then I get 'EU entry Not calibration mode! (Mode =
0x00) 'and then does nothing else, I hope I can
help, thanks from now!
hello
I finally entered the discharge mode and while carrying on the idt went for something to eat when I returned I showed up he was 100% complete, the phone went off and did not catch more! Does anyone know it could happen? Is there any way to restart?
please help
K3 AID program
reeprich said:
OK - I can summarize my experiencies:
IDT flash... I think everybody who is doing this experiments have this software...
K3AID... h++p://www.ulozto.cz/6556122/k3firstaid-exe
can switch phone to "download" state even if the HW keys are not working
it suppose working ActiveSync connection (downloaded from mobileuncle com) not my own sw...
Sometimes may be a bit dificult to get K3AID working.. it can show some error message like "RTM state Error" - You need to install h++p://www.ulozto.cz/6556123/cabviaactivesync-1-5-setup-exe
and h++p://www.ulozto.cz/6556124/gb-ppc-2-1-3-20090929-cab
it is only summarize of my experiences - none of this utility is mine, so use it on your own risk
Click to expand...
Click to collapse
@HTC_NEW: Did you do the following steps according to reeprich instructions? What was the end result?
I did read that you used the calibration menu but I expect that you should use the download firmware menu. Is that available? ( I had the software installed but my virus scanner complained that there is a virus in the tmp file...) What's more important if your phone does not work anymore... Please be aware that this is a possible virus.
Removing the battery for a couple of minutes can help for restarting the phone.
htc new
I have done the same thing with my t5388i clone from china.
I tryed to flah the ROM and now I have the white screen.
I used the SOLONOMI t5388i rom, and now it is BRICK - white screen.
Did you get your phone working back ?
Now i´m trying to use other ROM´s , but until now no success.
I used the SOLONOMI t5388i rom, and now it is BRICK - white screen.
Hi,
I had the same problem.
I used the rom postet from parabellum20000 (post # 1354) in this thread:
http://forum.xda-developers.com/showthread.php?p=8573304&highlight=Electronic+star#post8573304
parabellum20000 said:
Electronic star finally sent me (what they claim to be) SD ROM for t5388i. (99.3MB) I personally do not want to verify if it is truth, I am the one fortunate owner of perfectly (in some degree) working phone. Please feel free to use it on your own risk and share results if possible.
http://www.mediafire.com/?ymgvo8bf2t3v4c5
P.S.Please remember, flashing your phone with a wrong ROM is the safest way to brick (damage) it. So do not do it if it isn’t really necessary!
Click to expand...
Click to collapse
I hope this rom helps you to alive your phones again.
Cheers
5290
Hello good people from xdadevelopers,
PREREQUISITES:
I come to you as a noob seaking some answers. Somewhere in November I bought a Samsung Galaxy S2 from Orange that came with the Orange Branded software. Because the phone kept switching off (the Sleep of death bug, i think) I sent it in for service and it came back with the same problem.
Seeing that Samsung Keys does not have an option to restore the phone (as I could do from iTunes for my iPhone) I reflashed the phone with 4.0.4 Android XXLQ5 osing ODIN. The phone works better now, still get the SOD, but not as frequently.
The problem that I am facing now is that I cannot use keys anymore to update and since the 4.1.2 Update should start shortly I don't know what I can do to pass to the new version.
QUESTIONS:
1. How can I do a software restore from keys to the new Android version once an update is available?
2. Are there any precautions that I have to keep in mind since I have the LLQ5 version installed (I used the emmc checker from the store and my chip is "sane")?
3. If I flash the Orange version back from Sammobile, will I be able to use Keys again?
I have also added a screenshot of how the phone battery stats looked after recovering from a sleep of death issue just in case you know if it's another problem and I missed the diagnostic.
Link for screenshot: http://dl.xda-developers.com/attach.../3/5/4/7/5/Screenshot_2012-12-03-16-46-42.jpg
Thank you for your time,
Andrei Doru Tudose
download your branded stock firmware from sammobile...:good: when 4.1.2 rolls out:fingers-crossed:, flash downloaded stock firmware via odin n then connect to kies n you will be able to get official update...:laugh:
Peaceful Droid said:
download your branded stock firmware from sammobile...:good: when 4.1.2 rolls out:fingers-crossed:, flash downloaded stock firmware via odin n then connect to kies n you will be able to get official update...:laugh:
Click to expand...
Click to collapse
Hi Peaceful Droid,
Thank you for your answer. Could it really be that simple as flashing the official ROM and then the phone is yet again accessible through Keys?
If this is the only thing I have to do than thank you :laugh:
This phone has been a pest since I bought it. I don't know why Keys doesn't let you to simply make a restore to get a stock phone as you could in iTunes. There it was that easy, just connect the phone and click restore then set-up as new iPhone and problem solved. Back to stock in 30 minutes.
Thank you,
Andrei Doru Tudose
Yes. remember always read the instructions carefully and do it step by step and you will never face any issues...
and my dear friend if samsung also do as apple did then apple will knock doors of courts again...
nvingme bordars
Peaceful Droid said:
Yes. remember always read the instructions carefully and do it step by step and you will never face any issues...
and my dear friend if samsung also do as apple did then apple will knock doors of courts again...
Click to expand...
Click to collapse
Thank you once again, I just hope this solves the sleep of death issues this phone has All my faith in the JB update.
I still have 22 months of warranty left and if the phone keeps turning off I will send it back to them
Thank you,
Andrei - Doru Tudose
Hi,
I have the following problem, it's kind of long and I can't pinpoint the exact issue so I'm not certain what to do, update, flash, send it back in, ...
I acquired my S2 when it came out in our country and never had issues on gingerbread until wifi started to have very bad reception end of 2012. I was advised to connect to Kies and update the firmware to see if this helped.
Kies then updated me to 4.0.4., and the wifi issues were not solved; Instead, what I got was 'lag' i.e., the screen blocks from time to time, on basically anything, scrolling, gaming, video, etc., when you scroll through the start screens it's sometimes all very 'choppy'. Also, the phone rebooted from time to time.
Looking up what I could about all of this I found the brickbug issue and installed the app, and the phone turned out to have it. I didn't do a vanilla clean install when going from 2.3 to 4.0.4. and so obviously I couldn't do a factory reset now, so I decided to hand it in to the store I bought it, still under guarantee.
I got it back now, 6 days after which to me seemed a little fast, and it stated 'changed the module, updated firmware, problem lies with user's backup'. I turned the phone on again and after inserting all my info again and getting to the apps, I could see the problem was still there.
All I know right now after testing a number of things:
-Live streaming, playing video, angry birds, strolling through anything: It blocks from time to time. No major freeze, just very sloppy scrolling or for video's etc. it just stops for a second.
-Tested and still has the brickbug even though I noted this for the repair, and it's still stuck on 4.0.4.
-As far as I'm able to tell 4.1.2. isn't available for my country yet (Belgium) and anyway my CSC for some reason says 'Luxemburg' Keeping in mind I still have warranty, I'd prefer not to tinker around with Odin as I'm not familiar with it.
-RAM says 827MB out of which, when turning on the phone and just going into task manager, more than 500MB is already in use, which in my eyes might account for sloppy movement from time to time, but I have no idea if this might get better with 4.1.2. or if it might be linked to the memory and the bug.
What's the best bet for this, wait for 4.1.2. to appear for my country and update through KIES, and see if it gets better? That's what the technicians where the phone got sent from the store told me; If it's a bug in the chip or motherboard issues, it seems my country doesn't even have a samsung center so they'd need to push it up to level 3 technical issues and send it to another country, and if I can't prove the issue is hardware-related, I just get it back. The 'module' they changed they said was just an USB connection that was a little loose. After that they ran tests on it for 2 days but didn't find any issues (again, they don't test speed or chip/motherboard issues it seems)
Any help welcome
I'm guessing your device is not carrier branded (flash nordic LSD or the Netherlands FW).
On the other hand RAM usage and lagginess may result of carrier bloatware (so it is carrier branded....).
Which one is it, there are a couple of solutions for you.
Sent from the little guy
gastonw said:
I'm guessing your device is not carrier branded (flash nordic LSD or the Netherlands FW).
On the other hand RAM usage and lagginess may result of carrier bloatware (so it is carrier branded....).
Which one is it, there are a couple of solutions for you.
Sent from the little guy
Click to expand...
Click to collapse
Hiya,
No, I bought the phone just in the box in a shop, no contract, carrier, etc., I had multiple sim cards of different networks in side of it over the small 2 years I have it. I only had it back for 24 hours and basically didn't do anything with it except install 3 apps to test the things I mentioned, so I can't see bloatware being the issue.
Before updating to 4.1.2. and especially flashing with Odin (as said, I probably won't do until warranty is void in a small bit), is there a possibility the memory can be damaged due to the bug/chip/4.0.4., or is this kind of issue always related to firmware etc.?
Here's the info, if needed:
Model: GT-I9100
Android version: 4.0.4.
Baseband version: I9100XXLQ6
Kernel version:
3.0.15-157945
[email protected]#3
SMP PREEMPT Fri oct 26 16:17:36 KST 2012
Build number: IMM76D.XWLQ2
Bart D said:
Before updating to 4.1.2. and especially flashing with Odin (as said, I probably won't do until warranty is void in a small bit), is there a possibility the memory can be damaged due to the bug/chip/4.0.4., or is this kind of issue always related to firmware etc.?
Click to expand...
Click to collapse
AFAIK, if ur phone were affected and/or bricked by the brickbug before updating, it couldnt possibly be updated to 4.1.2. :screwy:
Sent from my SGS II
immortalneo said:
AFAIK, if ur phone were affected and/or bricked by the brickbug before updating, it couldnt possibly be updated to 4.1.2. :screwy:
Sent from my SGS II
Click to expand...
Click to collapse
Well, obviously all I know is that the scanning app detects it, wouldn't know what it's done for the rest, didn't brick yet in any case. so if you try to update and it doesn't work for this reason, any particular error message you're supposed to get in KIES?
Originally Posted by immortalneo<br />
AFAIK, if ur phone were affected and/or bricked by the brickbug before updating, it couldnt possibly be updated to 4.1.2. :screwy:<br />
<br />
Sent from my SGS II
Click to expand...
Click to collapse
<br />
<br />
Well, obviously all I know is that the scanning app detects it, wouldn't know what it's done for the rest, didn't brick yet in any case. so if you try to update and it doesn't work for this reason, any particular error message you're supposed to get in KIES?
Click to expand...
Click to collapse
Sorry mate.. no idea about that..
Sent from my SGS II
brick bug is software related.
Flash another ROM, JB is the obvious choice here.
Report back if lagginess persists.
Sent from the little guy
I just installed the latest Kies and connected it, but seems there is no 4.1.2. available yet with Kies. As I'm unfamiliar with any other form of upgrading, I'm guessing I'll have to sit it out, and who knows with my CSC in Luxemburg when that will become available, that country hardly has people in it lol.
Why wait? Just download Odin and flash JB.
Its easy.
It even has Belgium lang if im not wrong.
Its just normal flash no rooting etc.
Sent from my GT-I9100 using Tapatalk 2
There is no Belgian language, you're mostly either French or Dutch or, for a small minority, German
If it's not available yet, I'm assuming whichever JB I'd get and install through Odin will be rather visible I didn't install it 'officially', so if I would have any issue that would stay like the permanent lag under 4.1.2., I can't really hand in the phone again for repair or they'd notice (obviously, since with all repairs, they update the firmware themselves and would know it's not available).
Bart D said:
There is no Belgian language, you're mostly either French or Dutch or, for a small minority, German
If it's not available yet, I'm assuming whichever JB I'd get and install through Odin will be rather visible I didn't install it 'officially', so if I would have any issue that would stay like the permanent lag under 4.1.2., I can't really hand in the phone again for repair or they'd notice (obviously, since with all repairs, they update the firmware themselves and would know it's not available).
Click to expand...
Click to collapse
There is a Netherlands (Belgium) language possible.
For the warrenty thing: afaik there is a way to get from custom to stock without them (people of samsung) noticing (is this a right word?) it. Only when your cpu is dead you don't have the option to go back to stock.
Christiaan91 said:
There is a Netherlands (Belgium) language possible.
For the warrenty thing: afaik there is a way to get from custom to stock without them (people of samsung) noticing (is this a right word?) it. Only when your cpu is dead you don't have the option to go back to stock.
Click to expand...
Click to collapse
Well the language is not really an issue for me, as I put my gear in English. So far from what I found the only thing I could possibly do is install Odin and flash with a 'regular' 4.1.2. file, AFAIK and since it's not available yet, if I would keep my problems or even find any new ones, I'd either need to downgrade again or wait when it's finally released officially, Lord knows when that will be
Flash will take 5 min to do. Same as downgrade.
Sent from my GT-I9100 using Tapatalk 2
bihslk said:
Flash will take 5 min to do. Same as downgrade.
Sent from my GT-I9100 using Tapatalk 2
Click to expand...
Click to collapse
Yah, probably goes faster through Odin, the new firmware takes a Gig of space so Kies probably takes ages.
But as said I'm not familiar with Odin + if it doesn't solve the issue I'd need to bump it back to 4.0.4. and hand it in; If 4.1.2. becomes available officially and the issue remains I can hand it in with that and can write down the issue was both under 4.0.4. and 4.1.2. especially after I wipe everything under 4.1.2. and it still doesn't get better.
Bart, want us to walk you thru it?
The sooner you discover your device is faulty the better.
Notice that the guys at tge shop did everything we are about to tell you here. That's why your csc doesn't add up.
Sent from the little guy
gastonw said:
Bart, want us to walk you thru it?
The sooner you discover your device is faulty the better.
Notice that the guys at tge shop did everything we are about to tell you here. That's why your csc doesn't add up.
Sent from the little guy
Click to expand...
Click to collapse
Well both Luxemburg and Belgium are small countries so I'm assuming it's entirely possible one phone gets in a shop in the other, it's probably the same region, besides never had issues under gingerbread.
As for guiding me through it, I've been looking around for a good guide for a simple install but most of what you find are with remarks like 'Be careful to check and uncheck the right boxes or you might brick your device!' in Odin, then never an explanation about which boxes
I downloaded Odin (the new one, 3.4 or so?) and got it on a laptop, so all I'd need is basically getting the rom somewhere and being certain what to push and what not to
I'm a bit sceptic about a flash on the notebook too tho, it's not a very performant machine, but the rest I got are either on linux or in repair right now. I could put Odin on a desktop without network that's more reliable but it's still on XP so I'd probably need to get the 9100 drivers too then for it to recognize the phone correctly.
Anyway, all help is appreciated, I'll name my firstborn after your kittens in return!
Install Odin 3.07
Download RoM from SamFirmware or some other place
Place phone in download mode. Vol down+power+homebutton
When got in download mode press vol up
Now connect phone and start odin
Now you should se yellow colour in top in one of boxes and com port.
Now unzip rom
Put it in PDA
Now press start and wait.
When done you will see text PASS and green box.
Sent from my GT-I9100 using Tapatalk 2
lol, hate cats, don't worry. Name him/her Odin.
It's always better to flash via laptop, bo power off risk
You've got 2 choices here:
Flash via Odin: you'll need a pc and latest kies, plus s2's usb cable.
Once in odin you'll have to select 3 files from an extracted folder, check the ticked boxes and double check where did you place the files (it's easier than it looks).
Flash via Mobile Odin: Really easy flashing tool, no pc needed, all flashibg is done with your phone and the device itself does almost all the work.
It hardly goes south when flashing but when it does the life safe is regular Odin. This means that's it's the safest way to perform any first flash.
There are 2 versions, free and paid.
Free: manually download the kernel (easy to find).
Paid (root needed): Get's the kernel on it own, enables you to select EverRoot (roots any stock ROM while it flashes it allowing you to be rooted at all times) and inject SuperUser app as well as M.O app. Costs 5 bucks (around 3 euro).
Which way you wanna go?
Sent from the little guy
gastonw said:
lol, hate cats, don't worry. Name him/her Odin.
It's always better to flash via laptop, bo power off risk
You've got 2 choices here:
Flash via Odin: you'll need a pc and latest kies, plus s2's usb cable.
Once in odin you'll have to select 3 files from an extracted folder, check the ticked boxes and double check where did you place the files (it's easier than it looks).
Flash via Mobile Odin: Really easy flashing tool, no pc needed, all flashibg is done with your phone and the device itself does almost all the work.
It hardly goes south when flashing but when it does the life safe is regular Odin. This means that's it's the safest way to perform any first flash.
There are 2 versions, free and paid.
Free: manually download the kernel (easy to find).
Paid (root needed): Get's the kernel on it own, enables you to select EverRoot (roots any stock ROM while it flashes it allowing you to be rooted at all times) and inject SuperUser app as well as M.O app. Costs 5 bucks (around 3 euro).
Which way you wanna go?
Sent from the little guy
Click to expand...
Click to collapse
Ah, didn't know there was a mobile odin, didn't find info on that on any site I went to. Might be easier to just download that and any necessary files through wifi on the phone itself it it's simpler. I wouldn't mind paying extra, but I have no knowledge of root so I don't need it. I could always amuse myself with it when the phone is completely out of warranty anyway.
No root is needed for the regular mobile version? Odd, that's what I find on google. I'm assuming it doesn't show up in any of the 'regular' download options either on the s2
Odin: No root
MobileODIN: Root needed.
Sent from the little guy
Sorry for my english
This proplem I haven't seen before, it likes this picture, my homescreen always show this table I can't use lockscreen and everytime I hold power button, my phone poweroff insted of show power option. I tried swipe data but fail, reflashed stock rom via odin but fail again, this proplem still there can anyone help me??? Thanks!
anyone can help me?
123.xxx said:
anyone can help me?
Click to expand...
Click to collapse
I've have the same problem with a Sony Xperia ARC.
Help me please T.T
What country did you get your phone from? Where did you get the firmware that you flashed? Are you rooted? Custom recovery? And please post a screencapture of your setup in Odin before flashing, and after flashing.The table that is stuck on your homescreen appears to be some technical specifications and when comparing the PDA and CSC in the table (and presumably the versions on your phone) to the ones on SamMobile (based on the versions), it seems that the ROM on your device may be a test build. Your device may be a pre-release handset, that was for bug testing. I have heard of incidents when people buy pre-release handsets (when intending to buy a regular model). I suggest exchanging your phone for a new one if your problem can't be solved (wait another week beforehand in case we can fix it).
Codename13 said:
What country did you get your phone from? Where did you get the firmware that you flashed? Are you rooted? Custom recovery? And please post a screencapture of your setup in Odin before flashing, and after flashing.The table that is stuck on your homescreen appears to be some technical specifications and when comparing the PDA and CSC in the table (and presumably the versions on your phone) to the ones on SamMobile (based on the versions), it seems that the ROM on your device may be a test build. Your device may be a pre-release handset, that was for bug testing. I have heard of incidents when people buy pre-release handsets (when intending to buy a regular model). I suggest exchanging your phone for a new one if your problem can't be solved (wait another week beforehand in case we can fix it).
Click to expand...
Click to collapse
I'm in Vietnam, I had sent it to service center this morning, maybe they can fix it for me thank you for your help
Hi,
Did anyone experience some issue in the OTA upgrade to V12.0.3.0.QFQEUXM?
Now, at the first reboot after the upgrade, my touch doesn't work anymore and to unlock I used an external mouse.
I thought the V12.0.3.0.QFQEUXM was one of the "safe" roms without the bricking bug... But still, the touch not working isn't exactly good
Did you overcome this issue?
Thanks
I bricked my Mi A# trying to go back to a earier rom. Please just wait for an OTA to fix this, since you have a OTG to use mouse, youll be able to install it from the phone itself. Good luck
Bysholo said:
I bricked my Mi A# trying to go back to a earier rom. Please just wait for an OTA to fix this, since you have a OTG to use mouse, youll be able to install it from the phone itself. Good luck
Click to expand...
Click to collapse
i have the same case, do u mean that if xiaomi launch new fixed update rom/loader of android 11 we can install/load it from flashdisk using OTG cable?
I am facing the same issue. The touchscreen doesn't work anymore. Please help!
I brought the phone to Xiaomi repair centre and... They're scamming me!
They don't give me back the phone if I don't pay 20€ or if I don't pay 80€ to repair the back camera glass that has a small crack (for 6 months). They don't either check the issue if before I don't pay WTF!!!
And, official Xiaomi support via email agrees that, before checking the phone, I have to repair at my expense any scratch!!! And that they don't know about any issue on the Mi A3 FW!!! As if the dozens of wrong firmware of the latest year never existed!!! I'm speechless!!!
kerahledrek said:
i have the same case, do u mean that if xiaomi launch new fixed update rom/loader of android 11 we can install/load it from flashdisk using OTG cable?
Click to expand...
Click to collapse
Sorry I couldn't respond earlier. No, I meant that you can use the mouse to get to the Options menu and install the OTA update directly from the phone.
Bysholo said:
Sorry I couldn't respond earlier. No, I meant that you can use the mouse to get to the Options menu and install the OTA update directly from the phone.
Click to expand...
Click to collapse
That' is the only hope!
P.S. Here in Italy Xiaomy doesn't repair your phone really for free! If you have some scratches on the back a small sign on the camera glass, etc... They pretend that you pay them to fix the visual glitches and then they will repair your phone for the s**t they did!
So, they release public statements that they will fix the issue, and then in reality they scam you...
mr-mauro said:
That' is the only hope!
P.S. Here in Italy Xiaomy doesn't repair your phone really for free! If you have some scratches on the back a small sign on the camera glass, etc... They pretend that you pay them to fix the visual glitches and then they will repair your phone for the s**t they did!
So, they release public statements that they will fix the issue, and then in reality they scam you...
Click to expand...
Click to collapse
Sorry to hear that. I have same problem, touch not working after update to A11, bricked after downgrade to 10. Then i bring to service center, they fix it for free, even with unlocked bootloader (I'm living in Vietnam).
Unfortunately, at least here in Italy, Xiaomi seems a very unprofessional company (to not say something worst)!
They are not fixing it, they pretend money to before repair and replace unrequested component that have scratches, before even trying to fix the s*it they did.
For my point of view, I wouldn't anymore suggest to anyone to buy them. Because, if then this is the service you get, you save more money with any other brand that has a professional after sale support.
I got back my phone, I had to pay for it because they weren't fixing it for free, despite it was a problem caused by them (that's a joke Xiaomi)!
However, I received a new fw and with a mouse connected via OTA I installed it and, now touch works... But still, WTF Xiaomi, you create a global issue and then you spill money from clients? I got rid of the phone now and my next phone this year won't be a Xiaomi
same issue here, won't buy Xiaomi smartphone next time for sure.
I have a question: if a rom is buggy, is buggy FOR ALL USERS. But if some user (like me) don't have any bug... Problably is not a xiaomi issue. It's a user issue that don't have the skills to apply an ota update without mistakes. For example first a11 killer ota bricked all phones. But 12.0.3.0 that i have installed two months ago...have touchscreen working perfectly. So Good luck with yours futures Samsung... But if you don't be able to update a phone, don't incolpe xiaomi.
Anyway... Digit this * # * # 64663 # * #* and make the specific test...
hello, i recieved the march 21 OTA update yesterday, and after the final reboot, my touchscreen doesn't work anymore,
did you find a solution? i don't have a usb-c adapter so i can't try with a usb-mouse.
thanks
arjo656 said:
hello, i recieved the march 21 OTA update yesterday, and after the final reboot, my touchscreen doesn't work anymore,
did you find a solution? i don't have a usb-c adapter so i can't try with a usb-mouse.
thanks
Click to expand...
Click to collapse
First try an hard reset. Or better a clean firmware installation. But before try a touchscreen test. If is a little software problemi, the test solve it with a sort of recalibration
wetito said:
First try an hard reset. Or better a clean firmware installation. But before try a touchscreen test. If is a little software problemi, the test solve it with a sort of recalibration
Click to expand...
Click to collapse
hello, how can i do those things if i can't unlock the phone? i can't enter my pin code or my unlock pattern
arjo656 said:
hello, how can i do those things if i can't unlock the phone? i can't enter my pin code or my unlock pattern
Click to expand...
Click to collapse
Mmmm.... I suggest you a clean system installation via fastboot or with miflash in edl mode
I'm afraid the new android security system will ask me for my unlock pattern during installation.
How to enter in the EDL mode?
hello, after almost 2 months i managed to solve my problem. because of this fuc.... covid, I could not cross the border to take my mobile phone to the after-sales service, so I ordered a usb adapter to be able to connect a keyboard and mouse, and suddenly I was able to skip the unlocking pattern and go to settings to check for available updates, and luckily for me there was one of 43mb! After installing this update, the touch screen works again !!
arjo656 said:
hello, after almost 2 months i managed to solve my problem. because of this fuc.... covid, I could not cross the border to take my mobile phone to the after-sales service, so I ordered a usb adapter to be able to connect a keyboard and mouse, and suddenly I was able to skip the unlocking pattern and go to settings to check for available updates, and luckily for me there was one of 43mb! After installing this update, the touch screen works again !!
Click to expand...
Click to collapse
2 mounths??? in ten minutes you could have done this: download miflash tool, download latest stock mia3 fastboot firmware (also ota incremental are online!) and flash it with miflash
wetito said:
2 mounths??? in ten minutes you could have done this: download miflash tool, download latest stock mia3 fastboot firmware (also ota incremental are online!) and flash it with miflash
Click to expand...
Click to collapse
how can i do my unlock pattern without the touchscreen and the phone connected to the computer?