My M8S PRO W was bricked after a wrong flash.now i flash it with usb burning tool i have a message :
Romcode/Initialize DDR/Read initialize status/USB Control setup error​my mother board is rev2.1 and i can not flash it after many flash rom.please help
Follow the guide here: https://forum.xda-developers.com/t/reset-mecool-m8s-pro-blueboard-version.4560251/
Related
Hi,
I tried updating my XDA Atom to WM6 using one of the roms from this site. The flash worked up till the last part when it was meant to reboot when something wnet wrong and it crashed.
My Atom is now dead - no reset method works, even the soft reset and camera combo...
i think the bootloader has been corrupted.
So i followed the guides on this site and made the Jtag interface to reflash the bootloader. The cable works fine, the orange LED is flashing - i've installed the software, but every single time i try to flash the bootloader, i get the error below....can anyone help as i want to get my Atom back
PXA27x revision ??
Failed to read the Flash ID. Retrying 4 more times...
Failed to read the Flash ID. Retrying 3 more times...
Failed to read the Flash ID. Retrying 2 more times...
Failed to read the Flash ID. Retrying 1 more times...
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_0_2_32.dat
This program supports flash devices defined by DAT files
contained in the same directory as the executable program.
If the file cannot be opened, there are four possibilities:
1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.
anyone? i'm hoping there is something atupid that i've missed out which will get it working again...
HI, I'm having the same problem while trying to update my atom, now my atom dead. Can u Try to help me, since u got experinces of setting up the cable.. I don't knoe how to do the cable things ..pls help [email protected]!
manni said:
Hi,
I tried updating my XDA Atom to WM6 using one of the roms from this site. The flash worked up till the last part when it was meant to reboot when something wnet wrong and it crashed.
My Atom is now dead - no reset method works, even the soft reset and camera combo...
i think the bootloader has been corrupted.
So i followed the guides on this site and made the Jtag interface to reflash the bootloader. The cable works fine, the orange LED is flashing - i've installed the software, but every single time i try to flash the bootloader, i get the error below....can anyone help as i want to get my Atom back
PXA27x revision ??
Failed to read the Flash ID. Retrying 4 more times...
Failed to read the Flash ID. Retrying 3 more times...
Failed to read the Flash ID. Retrying 2 more times...
Failed to read the Flash ID. Retrying 1 more times...
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_0_2_32.dat
This program supports flash devices defined by DAT files
contained in the same directory as the executable program.
If the file cannot be opened, there are four possibilities:
1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.
Click to expand...
Click to collapse
Just try press and hold soft-reset button before run jflashmm.
Cheers,
Benz
manni said:
Hi,
I tried updating my XDA Atom to WM6 using one of the roms from this site. The flash worked up till the last part when it was meant to reboot when something wnet wrong and it crashed.
My Atom is now dead - no reset method works, even the soft reset and camera combo...
i think the bootloader has been corrupted.
So i followed the guides on this site and made the Jtag interface to reflash the bootloader. The cable works fine, the orange LED is flashing - i've installed the software, but every single time i try to flash the bootloader, i get the error below....can anyone help as i want to get my Atom back
PXA27x revision ??
Failed to read the Flash ID. Retrying 4 more times...
Failed to read the Flash ID. Retrying 3 more times...
Failed to read the Flash ID. Retrying 2 more times...
Failed to read the Flash ID. Retrying 1 more times...
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_0_2_32.dat
This program supports flash devices defined by DAT files
contained in the same directory as the executable program.
If the file cannot be opened, there are four possibilities:
1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
constructed filename. The first numeric value in the
filename is the device ID. Verify this value with the
component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
devices. Make sure that you are using the correct
platform data file.
Click to expand...
Click to collapse
Try to reset button before use JFlashMM. I'am same as problem with you. but i use resistance(R) is 390 ohm.(390*4)because voltage is more it damage to CPU or M-system chip, warn about long of wire connector if more long signal is loss. 1st. reset button Avery time as you flash JflashMM (JTAG). anf finally
my atom is incoming .......Good luck to you.
I have a problem when upgrading ROM: whether upgrade rom by SD or ASync, the progress bar always stucked at 36%. Any ideals?
Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.38
Selected Resurrector: [Toshiba TG01]
Connecting to the dead body...ERROR
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Model selected: TOSHIBA - Toshiba TG01
ERROR: The RTCK Signal does not respond.
any help?
soldered like the official foto
Hi,
Maybe this could help you : http://forum.xda-developers.com/showthread.php?t=1391435&page=2
if i put usb cable to comp i get
Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.38
Selected Resurrector: [Toshiba TG01]
Connecting to the dead body...OK
Detected dead body ID: 0x000000E1 - WRONG!!!
ERROR: Current ID does not belong to the Toshiba TG01 family.
What i see is that your FW version and JTAG Manager version is higher than the ones describe in the link i gave you. Maybe you can hanve a try with FW version 1.28 and JTAG manager 1.37
can it be because of bad grounding? or broken hardware?
try hd2 leo driver ... it will work ... and write a full backup ... it is about 512mb..
Yes I heard that too can solve problem...
but can also mean dead hardware on board, shorted pins >_>
it is second version of tg01 and it is a hd2 clone.... only first version of tg01 can be resurrected with tg1 driver
can someone provide me a new full backup link coz it's dead
Nokser, quin or ffboy have one for shure... I had one but lost it...
nyl said:
can someone provide me a new full backup link coz it's dead
Click to expand...
Click to collapse
http://rapidshare.com/files/422293658/Toshiba_TG01_Unlocked_Full_backup.rar
http://115.com/file/c29bz401#
Toshiba_TG01_Unlocked_Full_backup.rar
if you flash the full backup your imei will change ,so you use jtagbox write 0x00000000-0x01640000 flash ,it can unbrick your phone.
del...
Hi, please I need help with unbricking my tablet Prestigio 3870c duo. I done allready repair with AML burn.tool and my tablet start recognized . After i cant find any compatible firmware for 3870 then i use flash files for 3970 because i red on the net it is simmilar but not. Touch screen not anwear and colour display look funny. After that i find it official firmware for my tablet but it been too late. Now if i want to flash with any files all stop it with error : (FIND NO UPGRADE CONFIG- please load it manually and other one: can not open the file config_progress.xml\usb_spl.bin.
Can you somebody help me with this big problem . Thank you every one who going help me
Log from AML: -----importUpgradeFile-----filenameD:\adko\hu\Prestigio_PMP3870C_Duo\Prestigi o_PMP3870C_Duo\Firmware_Pres_pmp3870c_duo\update.z ip
[T 0][13:30:36]: load spl ...
[T 0][13:30:37]: can not open the file config_progress.xml\usb_spl.bin
[T 0][13:30:43]: failed ,current step is 1
[T 0][13:49:46]: load spl ...
[T 0][13:49:46]: can not open the file config_progress.xml\usb_spl.bin
[T 0][13:49:53]: failed ,current step is 1
-----importUpgradeFile-----filenameD:\adko\hu\Prestigio_PMP3870C_Duo\Prestigi o_PMP3870C_Duo\Firmware_Pres_pmp3870c_duo\update.z ip
hi every one,
i have a huawei y520-u22 dead after flash , i flash it with spft and it gives me 4032 error, what should i do to solve this problem?
You must flash y520-u22 flash file .. not another v.
Is that arabic firmware ??
Hi,
I think my Lenovo A536 just got bricked. I am trying to use SP Flash Tool to flash the original stock ROM and I am always getting one of these errors:
BROM ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
or
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (2004)
Once I got this one: BROM ERROR : S_BROM_CMD_JUMP_DA_FAIL (2035)
Can somebody help me? Is my phone totally dead or can I ressurect it?
SabiLP said:
Hi,
I think my Lenovo A536 just got bricked. I am trying to use SP Flash Tool to flash the original stock ROM and I am always getting one of these errors:
BROM ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
or
BROM ERROR : S_BROM_DOWNLOAD_DA_FAIL (2004)
Once I got this one: BROM ERROR : S_BROM_CMD_JUMP_DA_FAIL (2035)
Can somebody help me? Is my phone totally dead or can I ressurect it?
Click to expand...
Click to collapse
Nobody to help me?