Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.38
Selected Resurrector: [Toshiba TG01]
Connecting to the dead body...ERROR
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Model selected: TOSHIBA - Toshiba TG01
ERROR: The RTCK Signal does not respond.
any help?
soldered like the official foto
Hi,
Maybe this could help you : http://forum.xda-developers.com/showthread.php?t=1391435&page=2
if i put usb cable to comp i get
Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.30, JTAG Manager Version: 1.38
Selected Resurrector: [Toshiba TG01]
Connecting to the dead body...OK
Detected dead body ID: 0x000000E1 - WRONG!!!
ERROR: Current ID does not belong to the Toshiba TG01 family.
What i see is that your FW version and JTAG Manager version is higher than the ones describe in the link i gave you. Maybe you can hanve a try with FW version 1.28 and JTAG manager 1.37
can it be because of bad grounding? or broken hardware?
try hd2 leo driver ... it will work ... and write a full backup ... it is about 512mb..
Yes I heard that too can solve problem...
but can also mean dead hardware on board, shorted pins >_>
it is second version of tg01 and it is a hd2 clone.... only first version of tg01 can be resurrected with tg1 driver
can someone provide me a new full backup link coz it's dead
Nokser, quin or ffboy have one for shure... I had one but lost it...
nyl said:
can someone provide me a new full backup link coz it's dead
Click to expand...
Click to collapse
http://rapidshare.com/files/422293658/Toshiba_TG01_Unlocked_Full_backup.rar
http://115.com/file/c29bz401#
Toshiba_TG01_Unlocked_Full_backup.rar
if you flash the full backup your imei will change ,so you use jtagbox write 0x00000000-0x01640000 flash ,it can unbrick your phone.
del...
Related
Hello,
I tried to upgrade my imate with bluetooth (instead of cable, because it is in my job)and now the only thing i see in the screen is "Serial v1.02" I have tried to do a full reset but nothing changes. What can i do??? Thanksss
:lol: not buy serial cable!!!
there is an OFFICIAL UPGRADE ready and existing, but not yet PUBLIC,
it is one nice 40 MB RUU file which will uprgade your unit to english language:
Microsoft Pocket PC version 4.20.0 (Build 13252)
ROM version: 1.60.00WWE
ROM date: 12/03/03
Radio version: 1.06.01
Protocol version: 1337.16
ExtROM version: 1.60.06
Indirizzo http://xda-developers.com/incoming/rom160wwe/RUU16006WWE_T-mobile_NL.exe
IT'S FANTASTIC AND EASY WHIT THE USB CRADDLE
What you may try to do, for a start, is to reinstall the ROM upgrade once again, USING THE USB CRADLE and nothing else. Better remove the SIM card before installing the upgrade. Also, make sure that the battery is fully charged. All through the upgrade process, do not touch the device.
Finally....
Next day When i was in my job put my imate in the cradle, ran the upgrade and it worked.....I am happpppppy ¡¡¡¡
Upgrade failed
I had the same problem as dherrero. However, I have no luck as him. My XDA II still dead can not be boot. Anyone can help? Thanks.
IT's DEAD
I have a MDA from T-Mobile for 3 weeks now. I find out about the rom update (RUU16006WWE_T-mobile_NL.exe), tried it and got the message that the update failed.
On my MDA screen therse is only the message "USB v1.01".
Running the update again doesn't help.
Is there a solution or do I have to contact T-Mobile?
Hi all ,
One of my Friends had the same problem , he tried another computer and it works , then guess what was the problem ???? We found that it was ZONE ALARM !!!
So please check You'r computers guyes ,it might be another software makes the upgrade failed .
Thanks
Hi all!
We have to be aware, that the upgrade program says "NO PROGRAMS RUNNING ON THE PPC AND NO PROGRAMS RUNNING ON THE PC ITSELF"
It's a hard lesson i learned years ago while flashing a BIOS..... if possible, do it at an UPS equipped PC (or notebook btw) to reduce your chances of killing your device.
Windows XP has many more programs running than one would suspect. As a first measure, kill all the ones you can in the right side of your taskbar, shut down your Anti Virus and Firewall, and cross your fingers while upgrading.....
Should we also shut down Activesync? Or is it needed for the upgrade?
Thanx.
I am in the same boat this day. Please help !!! I tried to upgrade the imate threw the club imate ... i downloaded ok i believe ... i did not use the cradel just a mini sync usb cord ... i used this before many times to sync... but when i tried to run the official update it stopped and now it says only serial v1.02 when i put it in the cradel it says usb v1.o2 its dead... no light for batter scharge nothing???? no sync at all please help
ActiveSync is not involved in the upgrade process. The upgrade program runs out of this, with it's own connection and settings via USB.
I haven't used the mini cord, so I'm of no help about it.
Try the upgrade program again, looks like it failed to fully flash your ROM. (That's why you don't see the charging light, it's Software controlled)
Good Luck!
mm
Try to update your imate using a cradle connected to a pc(usb). It should work
i have the exact same problem as highlighted by the others here, USB and v1.02 screen. Question is, how do you continue to flash your rom after it fails and you put back your unit into the cradle and activesync does not sync it anymore
the upgrade doesnt use activesync so it doesnt matter. Just put the imate in the cradle(in other pc, if possible) and run the upgrade
qtek rom update problem
hi guys. my qtek only says USB v 1.02. I cannot do any rom flash. what rom should i use. where can i download it from?
Guys, I'm frustrated now. I've refreshed the ROM of my G4 version of Dopod 818pro (2.15.0001 or something I just can't remember). Unfortunately it fails and I cannot even turn the power on. My WinCE colleague told me that the Boot Loader was damaged. I am now seeking for some place to re-program the chip and hope if someone can provide me boot loader program. I really appreciate your guys help!!!
Are your Bootloader Realy damage? You mean you cant enter it? Or you havent Power to start your Device?
SD Flashing doesnt work without Bootloader!!
JTAG Flashing (hardware nearest Flashing!!) isnt developed for G4 Plattform. (i think so ... look in the Wizard board ... they talk about JTAG flashing and Wizard G4 must simulare like Prophet G4!!)
the bootloader really damaged, I cannot enter the three stripe screen by holding CAM, PWR button and hit reset hole. Do you mean that I even cannot use JTag to burn the chip???
I do have two fully charged batteries. But it should not be a problem of battery, I tried to connect it to charger but it gives no response, no LED
Using JTAG to revive a wizard is either a myth, or an undiscovered secret. If you cant get into bootloader, your chances of reviving your device are slim.
JTAG isnt a secret ... its more like ... hardware knowlage. If you know what IC is your ROM. You can found over the IC Spec the right Pins for JTAG Programming. If i can get a G4 S200, i can try my best.
yes, I know that using Jtag to rewrite boot loader is complex, but it seems like it's my last chance. NetrunnerAT I really appreciate your help but I'm in Shanghai, China so I have to find someone locally who can help me with that. Wish me good luck and I'll keep you guys updated about the result
If I can find someone who can help Jtag my phone, where can I find the correct bootloader program for my cell? is it downloadable?
guys, I finally found a place to revive my prophet. However, they don't know how to jtag it either, neither do they have a programer to rewrite the chip because they say the programer is very very very expensive. They just changed the old chip with one which has correct ROM and now my G4 Prophet turns to a G3 one...anyway, I can use it now.
Thx!
You have change your rom and it is now G3!!
Can you say me what IC they have exchange! If i know it ... and get a damage device, its possible to found a solution for all Prophet users!
No problem, I kept the damaged IC at home, I'll check the model No. and will let you know
er... One more question, I want to dump the current ROM to my SD card, however the wiki doc says it needs to unlock G3 first. But another doc also says unlocking G3 will downgrade my OS to 1.0.13.21. It's like a kind of deadlock, can I just unlock G3 without changing OS?
uhm ... i think you must downgrade your OS first to CID unlock ... after that you can upgrade to your rom and make SD-Dump!
ok, then that is to say i'll never be able to get a backup of the ROM I currently have.
I'll wait for some weeks and will try to "torture" my prophet again. It was just fixed and I'm supposed to "rest" it for some days, but sooner or later it'll be unlocked, hey heyhey....
Hi, I'm back, the chip is a "M-System MD8832-d16-v3-xp" with a clearly name "Disk On Chip" on it, hope this can help you locate the chip
http://www.m-systems.com/NR/rdonlyr.../0/EOL_DOC_G3_P3.pdf|EOL_DiskOnChip_G3_P3.pdf
Cool ... i read some PDFs ... this is are very nice entry in the PDF!
Compatibility Issues
The recommended replacement, DiskOnChip G4 1Gb/2Gb 9x12mm FBGA, and H1 2Gb
12x18mm FBGA are ball to ball compatible with DiskOnChip G3/P3 7x10mm, 9x10mm FBGA
products that are being discontinued. It is necessary to upgrade software based on TrueFFS 6.2.x
to TrueFFS 6.3.2 and above when upgrading to DiskOnChip G4.
If the different betwen G3 and G4 is the TrueFFS Driver and the G4/H1 is Pin Conpatibel ... possible if i get a half damage device i try to solder a H1 DOC on the PBC and reformat it.
[edit]Holly ****! THX i have found the Migration Document with JTAG Pins!!!
http://www.m-systems.com/NR/rdonlyr...MigrationGuideDOC_G4_1Gb_to_H3_1Gb_Rev0.2.pdf
how are you going to access the pins on a FBGA?
yanuk said:
how are you going to access the pins on a FBGA?
Click to expand...
Click to collapse
you dont. you take a bricked one, de-solder it, and manually trace them to somewhere on the motherboard using a multimeter.
can any body help me with a jtag points for a g4 wizard doomed with a incorrect ipl
Give me a damage Wizard board and i say the JTAG Pins! G4 and G3 have the same JTAG Pins.
I search for a damage Prophet to but i doesnt want pay over 80€ for a community project without any payment. It some on give me a wizard or prophet Board ... i desolder the IC ... search for JTAG Pins ... and reflash it ... send it back but working :->
the device doesnt damage if i resolder the DOC ... i have the right soldering mashine.
NetrunnerAT
Where you saw on DOC points jtag ?
You need the signals TDO TCK TMS TRST TDI.
DOC only memory and there no these signal.
What jtag you will use? And no program for flash DOC through jtag - see about Universal jtag.
I have a HTC HERM200, I did a hard reset, the problem is that no radio version and no protocol version displayed device information in parameters and of course impossible to operate my pocket pc as a phone and call using it !
I tried the hard spl 7.
for the 'info 7', this is the result :
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.10.Olipro
Built at: Apr 22 2007 13:32:26
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
(in windows, my version of herm is 200, here with the info_7 command it is herm100 !)
when typing 'rtask a', the answer is always command error !!!
how can I install the radio and is there a good version of WM6 compatible with my reference ?? if you can help me this will great for me
thanks !!!
Try reinstalling the shipped rom. You can also try a radio only rom but if neither of these 2 things work, you have a brick on your hands...
Sorry...
reinstalling shipped rom
thanks ultramag69 for your reply,
where can I download a good functional and compatible version for the shipped rom to my herm200 and how to proceed. I tried different version with unsuccess.
I tryed the 'HERM_Radinly_1.56.70.11_CustomRUU' using my sdcard proceeding with renaming the file .nbh to HERMIMG.nbh, the setup stopped at about 10%, and still there for more then 2 hours !!
installing with the usb cable stop always with error#262!
I wish I have a brick on your hands, this means that there is a way to recover the phone operational state !!
"Shipped ROM" means the rom that came on your Hermes. Generally a carrier has its own rom (you should be able to find on the carriers website).
Since you have Hard SPL on your Hermes use the sd card method.
1. format sd card fat32, copy .nbh file onto it & rename to "hermimg.nbh". Put back in Hermes.
2. Reset into bootloader - hold power,, ok button above flywheel and reset with stylus. hold in until tri-colour screen comes up.
3. If you did 1st 2 steps properly then follow the prompts.
This may take a while for the radio to install so give about 20-30 mins. Make sure you do this with a charged battery.
If this doesn't work then I'm sorry, but you have a brick...
You can still install an OS only rom but you won't have phone functionality again...
You can also try a radio only rom.. Above conditions apply...
Good Luck.
Hello,
I have a big problem with my german HTC Mozart ( T-Mobile version ).
2 weeks ago I flashed a RUU Rom to unbrand my mobile.
With this Software version my mobile is still branded and don´t work correct.
I would write more about the problems whith my mobile and this firmware, but my English is to bad….
After that I can´t flash any other Rom.
I tested to Install many other Roms, but the RUU installer every time says “Wrong Model ID”.
Then I looked my Phone Informations and see:
OS Version: 7.0.7004.0
Firmware revision number:2250.09.12803.111
Hardware revision number: NA
radio software version: 5.52.09.16_22.33a50.10U
radio hardware version: 0.0.0.0
Bootloader Version: 1.28.2250.3(113810)
Chip-SOC: 2.2.5.0
With the Rom, I flashed should be something wrong…
The Information on my Boot Mode Screen ( Rainbow) should be wrong, too
MOZA100 SS-BC (4K)
SPL-1.28.2250.3(113810)
MicroP (LED) 0x07
Touch C1(v69)
SD SANDISK 15193MB Class0
Partition Info-v211v413
In a german forum I found the same problem , but there are no solution.
Also I tested, to flash with a Goldcard.
I read all instructions to create a Goldcard an how to use it in this forum.
I think my created Goldcards are all OK but the USB HOST Screen every time says:
1. Loading
2. Checking…
3. And 3 second Later Serial on the bottom of the Display, but nothing else is happens..
Any Ideas?
so you have this problem for two weeks now?
what rom did you flash?
check the mozart forums:
http://forum.xda-developers.com/forumdisplay.php?f=779
and maybe this will help you:
http://forum.xda-developers.com/showpost.php?p=12120618&postcount=6
Yes, i have this problen for 2 weeks now.
It was a unbranded T-Mobile 1.28 rom.
Thanks, i have found someone else, with the same Problem, but no Answers.
see here
I have my Goldcards created with Ubuntu and Windows... Ubunto to find the CID and Windows, to create it...
And it seems to work, because the mobile is loading and checking the rom of the goldcard, but 3 seconds after checking... is the serial messeage in the bottom of the display and checking.. on the top, but nothing happens...
I had the same problem with my HTC 7 Trophy, flashing a new ROM did not work, and it changed the Model ID of the Phone. Once that has happened there is no way to flash a different ROM.
I tried various tools to try and get the Model ID changed back, if you use MTTY you can read the Model ID, but I don't think you can change it with that tool.
In the end I had to send mine to back to HTC to get the mainboard replaced.
hm sounds very bad..
but i think i saw the awnser somewhere...
try checking other wp7 devices forums,
hd2 people are very active..
hd7 people too...
somewhere ive read about some "force rom download mode" by pressing camera button on boot too, dont know if there was truth in it...
you say you had the t mobile 1.28 installed or you did try to install it?
it is not "unbranded" if its from tmobile (or do i get the term unbranded wrong?)
i belive there are 3 different t-mobile roms: TMO-DE, TMO-CZ, TMO-AT
these are all branded roms,
if you want unbranded you get: HTC-EU or HTC-Generic
ive used this method to unbrand my mozart from tmode 1.25 to tmode 109 to HTCEU 1.28
if you come from TMODE (as a german you should) you may want to try the 109 rom (works without goldcard)
so that i understand right, you can use the OS but you cannot make calls because of the cooked radio?
Hi, I have a German rom 1.28 installed, because i only can choose German or English language, but I do not remember which version it was. I think I previously had to install a 1.09.
However, there is something not been in order.
I think that the "force download mode" for this time is just for Zune, but I try to search for more information.
If I could flash any firmware I would do, but there is the problem with my "Model ID".
I think, the goldcard method is the right way, but it don´t works.
To eliminate errors about my hardware ( selfmade y-cable and hama 19in1 usb-cardreader ) I have ordered a delock y cable and a single usb-sd reader to try it on weekend again, but I think, the hardware is not my problem.
But i can test it not before weekend, because I´m a truck driver and only on the weekend at home.
Phone calls can I do with this firmware.
My display is out, if I choose a phone number. This time I only can hang up with the headset or by take out the battery
It works again until the other person accepts the call or the mobile hangs up automatically after 8 or 10 rings.
The volume of the headset ( earphones and micro), with this firmware is to quiet, too.
There are many problems….
somebody else with 1.28 and problems?
you dont need goldcard to flash back to stock rom
you should be able to flash any stock tmode rom without goldcard.
try to flash 109 without goldcard.
I´ve tried to install the
“RUU_Mozart_TMO_DE_1.09.001.16_5.50.09.15_22.23.50U_Signed_by_ansar”,
but after 1% my mobile reboots and the RUU Installer says:
244 wrong “MODEL ID”
are you sure it is a german Mozart?
this rom you flashed is made for unbranding.
Have you tried this?
http://forum.xda-developers.com/showthread.php?t=817691
just saying....
that suxx have you tried this?
Zetabit said:
Problem Solved!
Here are the steps I took to resolve the issue I was having, with the Mozart stuck at bootloader, "Enter USB Host...".
First I formatted the SD-card, then used my brothers Android phone with ASTRO File Manager to extract the CID code from the SD card.
1. Insert the SD card into the Android phone
2. Start the ASTRO File Manager
3. Navigate to sys/class/mmc_host/mmc1/mmc1:aaaa (instead of aaaa there could be something else as well)
4. Long press on the 'cid'-file
5. First select Open as, then Text
6. Then select File-Editor
7. Write down the number 1 to 1 onto your PC/Mac
Once I had the CID code, I used http://psas.revskills.de/?q=goldcard to generate & email me the goldcard image file.
I formatted the SD card at this point, FAT32, 4096 sector size.
I then used HxD Hex Editor and Disk Editor to copy the goldcard.img into the first sector the SD card.
Heres how:
1. Run HxD as Adminstrator
2. Open the SD card by going to Extras > Open Disk > Physical Disks (important) > Removable Drive. Make sure Open as Read only is unchecked.
3. Open the goldcard.img by going to Extras > Open Disk Image.
4. From the goldcard.img, Select All and Copy all bytes.
5. Paste into the first 384 bytes of the SD card - offset(h) 0x0 - 0x170.
Next I copied a European ROM on the the SD card (in explorer as you would with any file) and rename it to MOZAIMG.nbh
With the Y-cable I booted the phone and to my disbelief it started and successfully reflashed the phone.
http://www.youtube.com/watch?v=0t_xNdf9DeQ&feature=player_embedded
Hope this helps!
Click to expand...
Click to collapse
there has to be a way to fix it.. or maybe not
the other guy said he got his mainboard changed, maybe you broke it.. damn...
@pik.
I have tested to flash the "RUU_Mozart_TMO_DE_1.25.111.05_5.50.09.18_22.24.50_RELEASE", but after 1% the same problem "Invalid Model ID"
@webwalk®
I have created the gold card according to these instructions.
I have no Android phone, so I have the part to find out the cid solved with an Ubuntu Live CD and my built-in Cardreader.
The goldcard seems to work, since it goes from loading in checking..., then it is always the same on serial
Edit: Yes, I´m sure, that it is a German HTC Mozart.
i've the same problem with 1.28
can someone help us?
i have the same question
my hardware version is also NA
dsmps said:
Hello,
I have a big problem with my german HTC Mozart ( T-Mobile version ).
2 weeks ago I flashed a RUU Rom to unbrand my mobile.
With this Software version my mobile is still branded and don´t work correct.
I would write more about the problems whith my mobile and this firmware, but my English is to bad….
After that I can´t flash any other Rom.
I tested to Install many other Roms, but the RUU installer every time says “Wrong Model ID”.
Then I looked my Phone Informations and see:
OS Version: 7.0.7004.0
Firmware revision number:2250.09.12803.111
Hardware revision number: NA
radio software version: 5.52.09.16_22.33a50.10U
radio hardware version: 0.0.0.0
Bootloader Version: 1.28.2250.3(113810)
Chip-SOC: 2.2.5.0
With the Rom, I flashed should be something wrong…
The Information on my Boot Mode Screen ( Rainbow) should be wrong, too
MOZA100 SS-BC (4K)
SPL-1.28.2250.3(113810)
MicroP (LED) 0x07
Touch C1(v69)
SD SANDISK 15193MB Class0
Partition Info-v211v413
In a german forum I found the same problem , but there are no solution.
Also I tested, to flash with a Goldcard.
I read all instructions to create a Goldcard an how to use it in this forum.
I think my created Goldcards are all OK but the USB HOST Screen every time says:
1. Loading
2. Checking…
3. And 3 second Later Serial on the bottom of the Display, but nothing else is happens..
Any Ideas?
Click to expand...
Click to collapse
i also have this problem,somebody say that use the "JTAG"can fix it.
does anybodu solve this problem on mozart?
regards
please help if you can i cant flash any rom and i want to go to dft
please help i cant flash anything please any solution
my problem is very similar to yours. i have tmob de mozart too and this vender id error after flashing an official europe rom....
i ordered goldcard tools from amazon but they arent here maybe in three days. but i think it would be the same problem as yours.
->
i had at first the dynamics7 1.00 mango rom installed on my htc mozart.
after that i made rspl to 1.28.
after that i tried to install RUU_Mozart_S_HTC_Europe_5.12.401.02_5.71.09.02a_22 .51.50_RELEASE. the flashing started. than the phone restartet and installed spl 5.12 but the flashing doesent went to finish because of vendor id error.
now i cannot flash any stock tmob de or htc europe rom because of vendor id error. (clear because of spl 5.12) but the slspl rom doesent work, too. every flashing stops at 1%....
PD 67100 SS-BC (4K)
SPL-5.12.2250.2 ( 135167) MNG
os 7.10.8107.79
firmware 2250.21.51301.401
hardware 0004
radio 5.71.09.02a_22.51.50.21U
radiohardware A.102.0.D4
bootloader 5.12.2250.2 (135167)
any solution for me? is it maybe possible to send lower spl via cabsender?
Don't use wrong ver
aggelosss5 said:
please help if you can i cant flash any rom and i want to go to dft
Click to expand...
Click to collapse
Be carefull with DFT i halfbricked my bootloader, now I cant flash any rom, can't use the phone.
I am looking for new method maybe JTAG is the only way out of this.
Thank if helpful:good:
Hi,
I have bricked my phone
Before on boot screen it showed SPL 4.xx now it is disappeared and also some other information regarding to SD card is disappeared too.
Here is OS and phone details:
OS version: 7.10.7720
Model: HTC T9295
Varrier: AT&T
Bootloader4.5.2250
Chip SOC: 2.2.5.0
I was about to install HSPL and then windows Phone 8 but stacked. I think my phone have RUU OS as I don`t know how to test it. I have read warning on developer`s site, but never though this is for of my phone :S
Please Help
Regards,
Turkel.
trecords said:
Hi,
I have bricked my phone
Before on boot screen it showed SPL 4.xx now it is disappeared and also some other information regarding to SD card is disappeared too.
Here is OS and phone details:
OS version: 7.10.7720
Model: HTC T9295
Varrier: AT&T
Bootloader4.5.2250
Chip SOC: 2.2.5.0
I was about to install HSPL and then windows Phone 8 but stacked. I think my phone have RUU OS as I don`t know how to test it. I have read warning on developer`s site, but never though this is for of my phone :S
Please Help
Regards,
Turkel.
Click to expand...
Click to collapse
sorry bro your phone is full bricked...no way to recover from this situation... except jetung box.