Hello there! Ive got problem with boot of my device or/and problem with USB Burning Tool.
First of all ive tried few hours to put right image to my device. When i tried with S905W but got problems with Uboot in USB Burning Tool ("0x32030201]Uboot/Get result/DiskInitial error". But i tried S905X and it went well but only when i uncheck erase flash and boot sections. That was the only way to finish burning correctly. And of course its not working and hanging on Aidens Rom Logo (i was w8ing more than 5 mins).
When i check "erase flash and boot" sections ive got those mostly
[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
[0x00101004]Erase bootloader/Lowper/Identify/Error result
And yes ive done the Mask Rom thing :/
Pls help
Anyone?
only thing ican suggest is keep trying roms, maybe s905x will stick, it has for a couple of people before
Hi all,
Model : Wechip V8
Cpu : Amlogic S905W
Ram : 2GB Rom : 16GB
They have installed a different version on this device. The remote does not control, does not find wifi, does not connect to ethernet. I couldn't find original software. I found some stuff but I couldn't install it.
can you help me?
Thanks
I have been using W95 S905W android box since early 2018. Over that time, I have tested multiple firmware on it and all the compatible ones have worked without issues. Eventually, I reverted to the stock and used it for about 2 years. One day, I noticed lagging on the device and decided to reboot it but it didn't power on. Since September last year, I've been trying to flash the stock rom and the rest that had worked before but I have not succeeded. I'm getting the error uboot/get result/diskinitial always at 7%. The box is successfully connecting to my computer even without pressing the reset button. Does anyone have a solution to this problem? Thanks.
Related
I wanted to flash a box on android 5.1 and got a brick. Pre-backup was made in the TWRP, but now it is impossible to enter the TWRP. The USB BT device is detected, but the 2% load error flies. I think that the reason is in the wrong rom. I tried many different firmware and without results. backup made in TWRP is called: 1973-05-07--23-02-35_hx805a-userdebug_4.4.2_KOT49H_20171023_test
Hey there!
I somehow managed to red light brick my x96 mini s905 1gb/8gb, p282 board!
Now the reset button does nothing. I can't boot from any Burn Cards I've made.
Using USB Burn Tool, yields an error at 4% (for every ROM I try including stock rom)
I now have to short the pins to get my pc to even recognize the box and when it does, it fails at 4% in usb burn tools. No matter what settings I use (erase bootloader, erase flash ect)
I've been told these amlogic devices are next to impossible to actually KILL! So is there anyone around XDA that can guide me here?
I'm not new to flashing ROMs (been doing it since my samsung s3 lol) and I have flashed plenty of android boxes without error until this one!
I have a feeling I somehow deleted the bootloader! WHAT DO I DO NOW?!?!
Thanks in advance. Hopefully I've given enough information.
no solution ever for this brick?
found a possible solution
Hi, I just openend a thread where I was able to unbrick my x96mini box
https://forum.xda-developers.com/an...lved-bricked-x96mini-red-led-display-t3992403
I think the problem with this is the power cable is not being conncted after USB detection.
The board doesn't have enough power through USB alone to properly work, so connecting the power jack is mandatory. I failed the first flashing attempt for this reason.
Hope this helps, even when it has been months since OP.
Hi folks, I'm hoping someone can help me unbrick my MXQ Pro 4k. I've searched high and low for the stock firmware but it is nowhere to be found. My box seems to be a peculiar variant and the specs are as follow:
S905x 1GB/8GB S905XQ_V2.0 2017.05.16
SV6051P Wifi
SK Hynix H27UCG812ETR DDR3
It became bricked when I tried to flash different atvXperience firmware img files with the Amlogic USB burn tool. I had successfully flashed it with a version posted by minixfreak on the freaktab forums.
Although not with exactly the same specs, it worked pretty well except for the remote control wouldn't function. So I tried to flash again with what I thought was the stock firmware but unfortunately, that bricked the box pretty good. I tried to revert to the atvXperience firmware that worked from the post, but it now always fails at 7% when trying to format with USB tool. In all cases, I've tried every possible combination of pushing in the reset button in the AV port, shorting the NAND pins, switching the order of USB ports... The box always has a red light when powered and is always recognized by the USB Burn Tool driver when connected to the OTG port on the box but always stops at 7% when it attempts to format.
I hooked up a serial usb/ttl cable to capture boot output, turned on the box and it seems the box is in an infinite loop with the following output:
LOOP:8F;EMMC:800;NAND:85;SD:800;USB:8;LOOP:90;EMMC :800;NAND:85;SD:800;USB:8. It appears the bootloader is corrupt or maybe has been erased.
I tried making a bootable sd card using both burncard maker and bootcard maker but that didn't work either as it can't get past intial boot attempt, even pressing reset or shorting nand pins. I'm not sure if it's because of the boot loop or perhaps incorrect firmware. I haven't been able to find the definitive stock firmware anywhere. I would appreciate help in finding this elusive firmware.
I've scoured the internet for a solution and tried many different things but nothing can get me out of this loop. I'm now at a dead end.
I once had a bricked router that I was able to fix by connecting usb/ttl and putty and repeatedly hitting Ctrl-C after rebooting to get a CFE prompt. At that point I was able to manually flash the router with firmware and revive it. Maybe there's a tool available that would possibly do something like that with the android box?
Also possible I guess that something in the hardware is toast and it's just a paper weight now. Anyway, any help and suggestions would be appreciated.
Hello,
After trying to flash a Nexus rom on my tvbox, It bricked ( red led, not image, reset only working if I short 2 pins on the Nand ) . Now I can't find any rom for it, all of the firmwares I had tried to install stuck at 7% ( [0x32030201]Uboot/Get result/Disk Initial error ) with Usb burning tool. As for the SD card tries with Burn card maker, they do try to load the firmwares but stop at like 2-3 percent.
Is there any working, be it even stock firmware for this revision ?
Thank you.
Hi. Tested on my rev.2.3 if still looking for it
https://mega.nz/#!7IsxCKCS!ZDzQ9P3cCnmKjnl9s5dRJAFJTvGnxvxLSImlZr2PiHQ[/url
hi have you got the key for mega?
One year later bump. I bought a Tanix TX3 last year since I couldn't find a fix to my issue with the M8S Pro W but today I found the box while doing some cleaning so why not post again, maybe someone can help me with this bricked box issue.
Getting this error with usb burning tool with all the IMGs ( even Lunn ones ): 7% ( [0x32030201]Uboot/Get result/Disk Initial error ) M8S Pro W rev 2.3, p21x blue board, Spectek nand.
My original post from other forums:
Mecool M8S Pro W rev. 2.3 after trying to flash the Nexus rom on it. It bricked, red led, black screen, reset working, the only thing that worked was shorting the pins on the Nand flash. Now it gets detected by pc everytime I plug the usb into it. But...I can't find any good images to flash on it ( tried more than 15 of them ). Most of them get stuck at 4% with Usb burn maker or 7% ( [0x32030201]Uboot/Get result/Disk Initial error ). 90% of them aren't bootable with SD card maker, and those who do work, get stuck at like 2-3% on tv at "upgrading..." ( Lunn-NHG47L-20190418.114957.V0213.img , this one is among the few that is accepted by the tvbox on the SD card ). I am running out of ideas on how to get it working. Can anyone help me with a good firmware image ?
The board has a P21X motherboard and someone from another forum told me that I have SpecTek MLC-Nand FBML95B71KDBABH6-10AL
https://i.imgur.com/9YDyo4m.jpg
Edit: these are the IMGs I have tried so far =>*https://imgur.com/Yebndyl
Hi. Another link to download . img
https://mega.nz/file/7IsxCKCS#ZDzQ9P3cCnmKjnl9s5dRJAFJTvGnxvxLSImlZr2PiHQ
If its s905x you can try my rom
https://youtu.be/0uci6Rl70t4
This box was constantly freezing. Read somewhere that it requires a new firmware. The firmware that was on the box when I got it was 20181229. Tried to install a new firmware TANIX TX3 MAX & MINI "DUAL OS EDITION from usb stick using the method according to Tanix-box.com website " UPDATE FROM TF/USB MEMORY" . The software was loading fairly slowly so I stepped away for a moment and when I returned I had a blank screen on TV. Rebooted the box but only received the boot display and a black screen. realized I had bricked the box, Tried to download the same software using the usb burning tool but no go. I then tried the firmware TANIX TX3 MINI 20171220 using the usb burning tool. It downloads for about 7 seconds and then stops with an error. Obviously the wrong file. Here are the pics of my card. Sure hope someone can help me out. If I have to short a pin can you give me some details as I am pretty new at this. I do now have the original firmware and have looked everywhere, but can't find it. Thanks for any help on this issue, I've been reading and looking for a solution foe quit some time now.
Latest development, using USB Burning tool I loaded TX3Mini-20181210.img with no errors. I connected to TV and the T3 Mini logo cam on and the the android logo came on and was booting for just over 1 minute and then stopped and the display on the box was 0001.
billyfreeman said:
This box was constantly freezing. Read somewhere that it requires a new firmware. The firmware that was on the box when I got it was 20181229. Tried to install a new firmware TANIX TX3 MAX & MINI "DUAL OS EDITION from usb stick using the method according to Tanix-box.com website " UPDATE FROM TF/USB MEMORY" . The software was loading fairly slowly so I stepped away for a moment and when I returned I had a blank screen on TV. Rebooted the box but only received the boot display and a black screen. realized I had bricked the box, Tried to download the same software using the usb burning tool but no go. I then tried the firmware TANIX TX3 MINI 20171220 using the usb burning tool. It downloads for about 7 seconds and then stops with an error. Obviously the wrong file. Here are the pics of my card. Sure hope someone can help me out. If I have to short a pin can you give me some details as I am pretty new at this. I do now have the original firmware and have looked everywhere, but can't find it. Thanks for any help on this issue, I've been reading and looking for a solution foe quit some time now.
Latest development, using USB Burning tool I loaded TX3Mini-20181210.img with no errors. I connected to TV and the T3 Mini logo cam on and the the android logo came on and was booting for just over 1 minute and then stopped and the display on the box was 0001.
Click to expand...
Click to collapse
I installed TX3 mini 20181210.img on the box nd it worked. But the box is still freexing. Anyone else having this issue?
billyfreeman said:
I installed TX3 mini 20181210.img on the box nd it worked. But the box is still freexing. Anyone else having this issue?
Click to expand...
Click to collapse
Yo could try my custom Android TV 9 ROM, there are tx3 versions available, may work for you but no guarantees,
aidanmacgregor said:
Yo could try my custom Android TV 9 ROM, there are tx3 versions available, may work for you but no guarantees,
Click to expand...
Click to collapse
No doesn't work. Keep getting getinitial error