Hello. Is anyone there has a stock firmware for Jlinksz T906 ZH960. I flashed all the firmware that I can find here on XDA as well as other sites. The reason for this is because I'm finding a TWRP for this device to be flashed using SPFT. After I find one that fits my device, I immediately go to SPFT to flash it. But as I click the Download button, an error appears (something like PMT error) so I fix it by doing a FORMAT (worst thing that I did in my life) without backupping the rom because I am so sure that the firmware on this forum is actually gonna work for my device (which I realized it isn't). After formatting I can't open the device so I flashed T906 stock firmware (from the link above). After I flashed it, a lines on the screen appeared. This is the time that I realized that I'm f****d. So I went to Google and search for some more roms for T906 and I found this one that has a download link for a dump rom I think (the only firmware that I tried so far that has the display working properly). I downloaded it, flashed it and an error appears on the device "boot error!!!!!". After days and days of non-stop searching (went to some Russian and Chinese sites) on how to repair my bricked device it is time to ask for help. I flashed all the roms that I could find but only with this problem: black screen then suddenly turns off, a red or blue lines on the screen.
I recently found out that whenever I flashed the uboot.bin and pro_info of the rom with working display on some of the firmwares that I found, the display is working but the "boot error!!!!!" still haunt me.
Please, I need this device for online classes. If there's someone that can help, please.
See the attached image. That is the board model and the chips and all.
Before the problem (the time that I can fully use the device) I saw that it has an Android 9.0 Pie which is probably fake because I know for sure that it was KitKat.
Info on the back of the board:
ZH960-vEN000P
ZH960 TB-v4.1
B20200430_M116
ZH107ATB V4.1
Near the simcard tray:
ZH906-MB-v4.1
Jlinksz T906 tablet model
All help is appreciated
Thank you!
Related
Hello,
After tons of downloaded ROM's and weeks of webpages reading I' am still stuck in unbricking my Chinese tablet. These are my system specs:
Model: SAWEE10
Android: v2.3_20110926
Kernel: 2.6.32.9
Build: FRF85B
Mainboard: WWE101-MAIN (ver 3.4 2010/11/19)
Charger: 9V
No matter which version of ROM I have tested my device remains stuck at "Updating Image Linux-2.6.32.9" using a MicroSD prepared with WinHEX. Also the USB conection doesn't work anymore. It does start but freeze at Android green logo even if I left it for days. Can anyone help me with a correct ROM and flashing steps for this model? Many thanks in advance.
go back to where you purchased your tab from and download the rom for you tablet. the SAWEE10 is false.. i ran across that the software is a false positive.. the Tab is a 2.2 system not 2.3.. if it had superpad on the box it is a clone running on a unstable rom version from Ibex who makes the real flytouch 3. the best thing is to see if the seller have the original rom to flash your tablet.. i returned mine back and purchased a real system like acer iconia 500 from a box store.. have no problems since..
hope that helped..
Yes it's a pathetic clone and it seems that I have installed a wrong ROM version; also I wasn’t smart enough to make a copy of the original ROM (of course, my fault).
I have tried most of the ROM's present on the forums but the flashing operation freeze on "Updating Image Linux-2.6.32.9" and I don't know why. I have used the Flytouch ROM recovery, with WinHex SD formatting, and those images (ramdisk, system, userdata, etc) but doesn't work. Can be this Linux image writted separately?
try this it may help
androidtablets.net/forum/superpad-ii-firmware/12403-firmware-releases-firmware-files-benefits-bugs-flytouch2-v2-superpad-2-a.html
androidtablets.net/forum/gome-flytouch-ii-firmware/16530-rom-guide-superpad-flytouch2-wwe10-android-2-2-v2-1-3925-usb-flashing.html
poke around there you might find something
I came here after many days trying to fix this phone!
First, I don't know how to work with phones! It was looked due to "Too many tries to unlook it!" and was requesting to connect to one google account to unlook it.
The phone is a generic Spreadtrum SC6820 that has "i9300" writed on the space where the battery goes and its circuit board is marked with the writing L3035_MB_V2.2 and there one stick that reads L3035F-P9600-QUAD-2G-HY-V2.03.B05.
I was unable to find the stock firnware and did not know how to backup it using the ResearchDownload.exe tool available for the Spreadtrum, so I fallowed that very bad tutorial http://forum.xda-developers.com/showthread.php?t=2320640 and I ended with it bricked!
After that, I tried to flash all the roms I could find to see if any would work but all I managed to get is a phone with inverted color scheme, inverted touchscreen, no radio, no BT and no wifi!
If anyone here has the firnware compatible with this phone, please share it, Thanks.
i got the same problam my device has a inverted touchscreen after i flashed its rom using recherche download.please help
Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
rscredin The
up
My phone is experimenting some similar issue
I tried to change the recovery in my cubot one (the grey one), supossedly it has the mt6589t SoC, but every try failed, then I thought to change the firmware (the firmware the phone had was G800_CUBOT_D1_V1.3_"some_number_here"_MJK), with the firmware G800_CUBOT_D1_V0.8_20140124_MJK, i employed the SP tools without problem, the download was succefully, the i put the battery on again, then i switched it on, the telephone started, the screen lites on, but the screen keeps black, it sounds like boots normally, even the unlock screen sound normal, but there is no image in the screen, I've looked for the newer firmware everywhere but I did not found it, somebody could help me, please!!!
The firmware I used to flash the phone succesfully was the cubot one turbo available in the needrom page. Maybe the newer versions of cubot one have a new graphic chip or something different.
The error...
Alastor56 said:
Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
Click to expand...
Click to collapse
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Same prob.
I've same problem. Only black screen (but sounds like boot normally). Did anyone resolve this issue?
any solution found?
abanuelosh said:
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Click to expand...
Click to collapse
hi i have same problem, i install the rom that download of needrom but not work fine, i install the rom succesfull but my screen is black, phone turns on, I can unlock and lock it, volume buttons work, but there is simply no image.
are you have any solution?
Hello guys,
I have an Star S7189 Phone which I had to return to stock (the owner tried to root but failed and wanted me to get rid of the root), but now that I flashed the stock rom the Display is totally glitchy.
The Device boots fine and I can even flash a custom recovery but even there the screen is glitched. (its basically unusable right now in this state)
I have to return it (working) to the owner.. or he will blame me (understandable)...
I flashed the following rom:
http://www.needrom.com/download/star-s7189s/
because it was the only one I could find that SP-Flashtool would let me flash.. (the other roms are all for MTK6589 but this device seems to be a MTK6582 one - at least thats what SP-Flashtool recognizes it for.
When I ran CPU-Z before all this it said 6589 though.. ?!
---
Usually I manage to fix things, but in this case I'm out of ideas.
When I got the phone it had a newer Firmware Version installed than the one I got now (it was from 2014) but I just cant find any other rom for the MTK6582 model than the one above...
Another weird thing: The sticker under the Battery says Quad 1.6 Ghz - but the MTK6582 is not 1.6 GHz is it?
I really hope anyone can help please !!!!!
I either need another rom or find a way to fix the display... I already thought it might be a hardware issue because even the battery charging screen and the custom recovery screens are affected by the glitches - but it was working alright before.. (with a half assed root which was not working .. or else I wouldnt have tried to flash stock rom anyway...)
HALP!
Additional Infos:
I *think* the rom has the wrong lcd drivers or smth .. because even I can't really "see" them, there seem to be onscreen buttons for menu and back, ALTHOUGH the device has hardware buttons for that - and the old rom didnt have any onscreen buttons showing ....
Please guys, if anyone knows a bit about those MTK china stuff please think of a way how to fix this thing .. I'm really out of ideas..
I have loaded that "MDT Flash Tool" which lets you choose drivers for lcd etc.. but this damn thing does not accept the MTK6582 rom which I need to flash - with MTK6589 roms (which do not work for the device) it opens them fine...
This could be the first soft-brick that I really cant fix ........and its due to lack of files it seems..?
Any way that I could "mod" the rom to get the display working?
Hello All!
I have a problem with one of my tablet.
I bought it on Irulu's website,Expro X1 plus.
After a couple of mounth I had to send it back for change it to a new one.
Got it and want to change the firmware again( 4.4 ),but I got an error message in Phoenixsuit: Download boot1 failed.
I found another firmware ( 5.1 ) and tried to flash and worked,the tablet started but no SD card and camera
So my first tablet was the same like the second inside and outside too.Checked the mainboard.
Tried different cables,programs,computers ....
What am I do wrong?
Thanks