Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
rscredin The
up
My phone is experimenting some similar issue
I tried to change the recovery in my cubot one (the grey one), supossedly it has the mt6589t SoC, but every try failed, then I thought to change the firmware (the firmware the phone had was G800_CUBOT_D1_V1.3_"some_number_here"_MJK), with the firmware G800_CUBOT_D1_V0.8_20140124_MJK, i employed the SP tools without problem, the download was succefully, the i put the battery on again, then i switched it on, the telephone started, the screen lites on, but the screen keeps black, it sounds like boots normally, even the unlock screen sound normal, but there is no image in the screen, I've looked for the newer firmware everywhere but I did not found it, somebody could help me, please!!!
The firmware I used to flash the phone succesfully was the cubot one turbo available in the needrom page. Maybe the newer versions of cubot one have a new graphic chip or something different.
The error...
Alastor56 said:
Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
Click to expand...
Click to collapse
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Same prob.
I've same problem. Only black screen (but sounds like boot normally). Did anyone resolve this issue?
any solution found?
abanuelosh said:
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Click to expand...
Click to collapse
hi i have same problem, i install the rom that download of needrom but not work fine, i install the rom succesfull but my screen is black, phone turns on, I can unlock and lock it, volume buttons work, but there is simply no image.
are you have any solution?
Related
bought a phone advertised as ulefone u692.
tried to flash cwm to devive , lost recovery.
tried to flash stock firmware to device in hope of fixing afore mentioned problem.
epic fail phone boots but screen is black.
after many attempts and downloading numerous roms and flashing numerous file....finally get it to boot but with several driver issues! many sensors not detected.
what i have found out is the screen is 1920x1080 as opposed to the ulefone u692 which has 1280x720, hence the black screen issue.
everything else says it is right apart from screen resolution.
i do hear cpu info can be faked, how do i check my real cpu info?
would it be possible to add the screen driver to the stock u692 kernel?
thanks.
Hi bro
Please remember , always backup all partitions first on unknown mtk phones.
i wonder your IMEI isn't lost too,
try this tool -> http://forum.xda-developers.com/showthread.php?t=2160490
Don't buy copycats....
So I tried to flash TWRP with Flashr on my J3, but when I booted into recovery a blue screen came up saying that system software not authorized by AT&T was found on your device. I got nervous and decided to flash a stock firmware on to my J3, but it fails every time. I finally got to like 10% but then it failed and a blue screen saying,"An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software." Smart Switch crashes every time I put in my serial number though so now I'm stuck with a bricked phone. Any help would be greatly appreciated :fingers-crossed:
lolcoder124 said:
So I tried to flash TWRP with Flashr on my J3, but when I booted into recovery a blue screen came up saying that system software not authorized by AT&T was found on your device. I got nervous and decided to flash a stock firmware on to my J3, but it fails every time. I finally got to like 10% but then it failed and a blue screen saying,"An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software." Smart Switch crashes every time I put in my serial number though so now I'm stuck with a bricked phone. Any help would be greatly appreciated :fingers-crossed:
Click to expand...
Click to collapse
Try flashing again with Odin, but this time use older versions, maybe v3.10.6 or v3.09.
Solution
I flashed a random root file that I found on another xda post and it managed to boot.
lolcoder124 said:
I flashed a random root file that I found on another xda post and it managed to boot.
Click to expand...
Click to collapse
Next time, try not to flash files blindly, because any file that is wrong can brick your phone.
Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
flagpol said:
Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
Click to expand...
Click to collapse
Do you find the solution yet? Cause I face the same problem too..
Tzul please help.. :crying:
me too, please help
similar issue, cant power on, keep on vibrate loop interval, no display, not detected by pc
flagpol said:
Yesterday, I flashed Tzul's S000031 ROM for the Lenovo Tab3 7 Essential (TB3-710I). It was a successful root, until after I started the tablet again, it only let out a long vibrate, with short vibrate intervals after about 5 seconds.
I first flashed TWRP on the tablet yet I think it did not load, as I started into recovery yet saw the Android Stock Recovery running.
I've been looking at guides, flashing other versions to no avail. SP Flash Tool always shows that it cannot load DRAM (4032 error or 0xFC0 error).
This happened for the first time that I've been flashing and rooting phones. I hope you help me out here.
Click to expand...
Click to collapse
Hi, did you find anything?
I have three TB3-710l (they are the company I work for), I have successfully root 2 of them but the newest tablet doesn't have the same luck.
First I install TWRP by Tzul, but the TWRP have an error never mount anything.
Second I try to flash stock firmware (Lenovo_Tab_3_TB3-710I_MT6580_S000032_160921) then the same happened, never turn on and just vibrates.
Always using SPFT, and now I have the same problem has you: always shows that it cannot load DRAM (4032 error or 0xFC0 error).
EDIT: Hi, for everyone who get in here with this problem, please read all this thread.
I unbrick my tablet with this answer in specific.
Good Luck!
asdrubalsantander said:
Hi, did you find anything?
I have three TB3-710l (they are the company I work for), I have successfully root 2 of them but the newest tablet doesn't have the same luck.
First I install TWRP by Tzul, but the TWRP have an error never mount anything.
Second I try to flash stock firmware (Lenovo_Tab_3_TB3-710I_MT6580_S000032_160921) then the same happened, never turn on and just vibrates.
Always using SPFT, and now I have the same problem has you: always shows that it cannot load DRAM (4032 error or 0xFC0 error).
EDIT: Hi, for everyone who get in here with this problem, please read all this thread.
I unbrick my tablet with this answer in specific.
Good Luck!
Click to expand...
Click to collapse
THis might WOrk i ve havent tried yet ,tho i wanna flash it now
https://forum.xda-developers.com/android/development/tb3-710i-tb3-710f-rom-stock-rom-lenovo-t3437810
same problem faced,can any developer please help us
Hi i am new in this foro, i have a problem with my Homtom HT16. It does not work, when I try to turn it on, it vibrates and the initial screen with the Homtom logo appears and then several lines and stripes appear in the lower half of the screen and until it arrives it never ends.
Searching several tutorials I found that installing the official rom would be solved, I proceeded to download it along with other tools, the SP flash tool and some drivers ... Perform the procedure step by step as it appeared in the tutorial but the problem persists.
Due to the problem that the screen is blocked with several lines, it is impossible to enter recovery mode. If you can help me and tell me if this has a solution I would appreciate it
Is there any solution available?
I have the same problem, could you solve it?
install a custom rom
todociber said:
I have the same problem, could you solve it?
Click to expand...
Click to collapse
hi, i solved it for my own.
First, download from the oficial web site, rom v9
second install it with SP flash tool
third That firmware has problems, it show a error of setting. So download TWRP and later root your phone.
fourth search for a custom rom, install it, and you will ready to use your phone.
I use lineage rom but it has some bug with camera and display, now i'm searching for other
Hello. Is anyone there has a stock firmware for Jlinksz T906 ZH960. I flashed all the firmware that I can find here on XDA as well as other sites. The reason for this is because I'm finding a TWRP for this device to be flashed using SPFT. After I find one that fits my device, I immediately go to SPFT to flash it. But as I click the Download button, an error appears (something like PMT error) so I fix it by doing a FORMAT (worst thing that I did in my life) without backupping the rom because I am so sure that the firmware on this forum is actually gonna work for my device (which I realized it isn't). After formatting I can't open the device so I flashed T906 stock firmware (from the link above). After I flashed it, a lines on the screen appeared. This is the time that I realized that I'm f****d. So I went to Google and search for some more roms for T906 and I found this one that has a download link for a dump rom I think (the only firmware that I tried so far that has the display working properly). I downloaded it, flashed it and an error appears on the device "boot error!!!!!". After days and days of non-stop searching (went to some Russian and Chinese sites) on how to repair my bricked device it is time to ask for help. I flashed all the roms that I could find but only with this problem: black screen then suddenly turns off, a red or blue lines on the screen.
I recently found out that whenever I flashed the uboot.bin and pro_info of the rom with working display on some of the firmwares that I found, the display is working but the "boot error!!!!!" still haunt me.
Please, I need this device for online classes. If there's someone that can help, please.
See the attached image. That is the board model and the chips and all.
Before the problem (the time that I can fully use the device) I saw that it has an Android 9.0 Pie which is probably fake because I know for sure that it was KitKat.
Info on the back of the board:
ZH960-vEN000P
ZH960 TB-v4.1
B20200430_M116
ZH107ATB V4.1
Near the simcard tray:
ZH906-MB-v4.1
Jlinksz T906 tablet model
All help is appreciated
Thank you!