Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
My phone is a little over a month old, and I'm getting desperate. I've been temporarily using a clear thing (case mate) AT&T sold me with the phone (it was all they had that would fit) until I found something that would work for me. I've been reading here, and finally took the plunge to get the Designio case discussed here:
http://forum.xda-developers.com/showthread.php?t=584093
Unfortunately, either I got a bad case or I'm being too picky or whatever, but I'm not pleased.
My criticisms are:
The PTT button completely covered by the leather support piece (not sure that's what to call it, but there's a leather piece that runs along the left edge, or bottom with the keyboard open). The PTT button is still functional as long as I press the leather piece just right.
The plastic over the keyboard does not fit snuggly -- it bulges up about an eighth of an inch along the bottom of the keyboard (the left side of the phone), which is annoying enough when using the keyboard, but that bulge also keeps that edge of the phone from closing flat when then keyboard isn't out. I carry my phone in a dedicated pocket in my purse, and I'm constantly finding dust & such that gets under the loose plastic keyboard protector at the bottom of the keyboard (left side of the phone when the keyboard is closed) since there's a gap along that edge from the loose plastic. That's highly annoying for me.
#2 might not be much of a problem if the magnetic closure was snug, but it's not -- IMO, it's off by a little over a quarter of an inch. This allows the top cover to slide around enough that the screen isn't protected when the case is closed (particularly the bottom of both sides up about 2.5" and up to 1/2" in from the bottom corners). If the magnetic catch was appropriately placed, it could also eliminate the gap on the left side of the phone when the keyboard is closed.
Clearly, this isn't the perfect case for me. I thought perhaps I was being too picky, but the Krusell case for my old 8525 doesn't suffer from these problems.
So, if anyone has found a flip case (preferably leather, but that's not a deal breaker) for the AT&T Tilt 2 that doesn't suffer from these problems, please share
TIA,
Saundra
i'm not entirely happy with mine, but mine seems not to have the problems that you are finding wiht yours.
i use the Capdase case, http://www.capdase.com/en/product4.php?cid=1&bid=5&mid=48, and it's a soft leather case that comes in two styles, either a "book"/side flip, or the top flip which i got.
main pro is that it uses small tabs on all 4 corners to clip on to the lower/keyboard half of the phone, allowing you full access to all buttons, the usb port, and the keyboard, without any plastic in the way. the tabs also seem to be more robust and likely to last longer than the seidio innocase tabs which i used on my kaiser. those tend to wear down and break off after about 2 years of use.
on the cons, i dislike the flap, which only has room to store 2 microsd cards and 1 extra sim card. i've already lost 1 sd card, though i am not 100% certain if it was my fault or the case (i was showing the phone to some friends the night i lost it). it also does not have any storage space for a credit card or similar, even though it would've been minimal cost to add one.
if only i could have the flap from your case, and the base of mine. then it'd be perfect.
Thanks for the input! It does sound as though we could have the perfect case with your base & my flap.
I'm in the US, and I couldn't find any retailers for that particular Capdase -- lots for iPhones. Of course.
It looks like I could maybe get it through eBay, which is good to know in case I just can't get the Designo to work for me.
Thanks again!
sslund said:
Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
http://www.noreve.com/brand/HTC/product/Housse_cuir_HTC_Touch_Pro2_Verizon_-_Sprint_Tradition.html -This works well for me, but there are no pouches for SD cards
Click to expand...
Click to collapse
Noreve
I am using the Noreve case available at www.noreveusa.com I like it a lot. It too covers the push to talk button, but since I'm using a custom ROM it has no functionality anyway. The Piel Frama case I had for my Original Touch Pro, there was that darn plastic sheet covering the keyboard and frankly I think that sucks. Granted the noreve case is squirrely when the keyboard is open, but unless you are able to drive and text or ride a bike and text or a motorcycle and text, well you'd do better to spend your money on a funeral plan than a case. My only complaint about the Noreve case is the belt clip sucks. I am using an old Piel Frama belt clip since it fits my belt better. I also personally LIKE the looks of the larger Piel Frama TP2 case, but most have commented on how ugly it looks.
If you're crafty...
As we've come to realize, ATT has delivered the Tilt 2 in a state that requires serious hacks to make the simplest changes. In keeping with that line of thought, I've modified a clear plastic case and added a leather flap with a pocket for credit cards and memory stix. And - Unlike some commercial flaps, when this flap is closed, nothing can slide out of the pocket. Here's how you can too...
Note to Boy Scouts: I've included more detail below than many of you here may need. After buying the case, reviewing the pix and the dimensions, you may be able to fore-go most of the tedious instructions below.
PIX
I've posted a series of pix on photobucket (sadly, I'm too new and untrustworthy to provide direct links to them here). To review the photos:
1. Go to the PhotoBucket website.
2. Click the Drop-down arrow on the right side of the "Search" box and select "People" for the search type.
3. Search for my id, "fractalcracker". Zoom in to view the 5 photos in the default album.
Plastic Case
Two-Piece (front and back) Plastic Case from the ATT store: $29.99 (ridiculous, yes I know...). Find it online at the ATTWireless website by searching "Accessories" for part number "75525". The Back piece clips on to back of phone and allows you to access all buttons and slide open the keyboard. After adding this leather flap, you won't need the front piece of the case.
Leather Pocket Flap
The leather flap is similar to a wallet pocket. In fact you might be able to cut a wallet apart to make the flap. I'll give you directions to make this one by hand from a small piece of leather. If you don't have scrap leather, cut up your wife's (or your own) purse. Good luck with that one...
Leather Measurements:
You'll need a thin, pliable piece of leather 4 inches high by 5-1/2 inches wide. We'll cut 2 pieces as follows...
Outside flap piece:
3-1/4 inches wide from left to right.
4 inches high from top to bottom.
Pocket piece:
2-1/4 inches wide from left to right.
4 inches high from top to bottom.
Assembly
1. Cut leather pieces.
2. Lay the smaller (pocket piece) on the table so that what will be the 'hidden side' (inside of the pocket) is facing up. Align it so the narrow edge is closest to you.
3. Apply a thin bead of super-glue to the top, left and bottom edges of the pocket piece. The 4th, unglued side will be the opening of the pocket.
4. Lay the flap piece down on the table so the inside of the flap is facing up. Align it so the wide edge is closest to you.
5. Pick up the pocket piece and flip it over from left to right so the glue side is down. Align it above the right side of the flap piece and glue the 2 pieces together so the top, bottom and right edges are aligned.
6. To form the hinge, apply a thin bead of super-glue to the flap piece, running from top to bottom along its left edge (opposite the pocket).
For below - remember, we're only referencing the back side of the plastic case - not the front.
7. Lay the plastic case on the table, 'opening-side' up. Rotate it so the camera hole in the back cover is furthest from you. Slide the plastic case over so the right edge of the plastic case is aligned next to the left edge of the leather flap (pocket side up with pocket on the right side of the flap).
When we glue the flap to the case, we want the super-glued hinge joint to be about 1/16th inch below the face of the plastic case. That way, the leather flap will bend back enough to allow the phone screen to slide over it whyen you slide open the keyboard.
8. Stand the plastic case up by raising the left side and tilting it to stand on its right side. Align the right side of the case above the glue line on the left edge of the leather flap.
9. Press the right side of the plastic case down in place on the flap piece so the glue line on the leather flap is about 1/16th inch below the top face of the plastic case.
When it dries, press the phone into the plastic case and get on with your life!
May the force be with you...
Mark
I'm half way through the mod but I wanted to post a small dissably guide.
Be careful. It's only plastic and don't blame me if you break it.
1) Remove the rubber pads at the bottom of the keyboard to reveal 5 screw and remove those too.
2) Remove the two little rubber covers from the dock to reveal 2 more scres and remove them.
3) Use a plastic tool to split the keyboard and prise apart the plastic clips holding the bottom and top halves. I used plastic dental tooth picks and found it easiest to start from the hump at the top left back of the keyboard. Be careful and work slowly and as gently as you can to avoid damaging the clips.
4) Use a flat headed screw driver to press the clips on the underside of the white half of the keyboard to unfasten the black dock. I found it easiest to work from the middle to the ends and then gently flex the dock to pop it out.
Sent from my GT-P6800 using Tapatalk 2 Beta-2
You got guts..lol
Sent from my GT-P6800 using xda premium
Job basically done.
It's in two sections: a bracket and a cowl. Both made from sheet aluminium and made not to fit the phone but the Anymode case I have.
The bracket was a bit tricky and took two or three attempts to figure out something which would work. It is held on by the two screws in the trough of the dock and some heavy duty double sided tape placed along the narrow ledge which the dock clips into. While I would prefer to use a more permament fixing, like the plastic clips or screws to attach it, it is, at least currently, of similar strength to the plastic dock and at least as stiff.
I used a vernier guage to measure gaps and distance on paper to draw up a template. Glued the template to some aluminium stock and cut it out. I left fold lines on the template and used a vice to make the most important, long bends an pliers for bends which wouldn't be possible with the vice.
Two tricky areas: the bottom of the tough back bend was made in two 45 degree bends, since it was difficult to match the curve of the molded plastic and the the bottom screw holes are very hard to locate and need to be countersunk since the screws in the black plastic dock are recessed and very short.
Sent from my GT-P6800 using Tapatalk 2 Beta-2
I forgot to mention: the keyboard mappings are not all the same for the function keys although the small keys, along the top row, are easy to pop off from the bottom corner and pop back on in the correct keys. The bigger main keyboard keys are different and so far I've left them in place because they hold on like limpets. One last note, caps lock doesn't work.
Sent from my GT-P6800 using Tapatalk 2 Beta-2
Just wondering if it would be possible to remove the bottom section of the 'aluminium' frame the the ZU. The specific part of the frame is apparently made of a softer plastic which means it gets dented easily such as in my case. I've already purchased replacement materials but have no clue how to remove the originals. Any ideas?
Yeah, it's possible but I have no idea how. My guess is to remove the back panel, and then loosen the lower part. You can get the back panel off by heating it so the glue that holds the glass gets warm, and making the glass removable by using a small suction cup. I believe there are a few videos on YouTube, so I recommend you checking them out. Also, search for how to remove that bottom part on YouTube too if you haven't already.
Hi, I just replaced the back for a new one (fully assembled). The problem is that dust enters the main camera (just the main camera, not the wide angle camera). I guess it's a bad assembly of the rear glass.. It's not sealed.
My question is what to do with it? I guess I can put glue on the outside to seal it but it will look ugly. It will work, but will look ugly. I think the dust enters from the side on the flash/laser module.
Any recommendations?
Sounds like a bad assembly, yes.
What I would do if I were you is to open the phone up (ifixit has a nice, comprehensive guide to teardown), clean the camera and the glass that covers it on the inside, and either glue it or use some 2mm 3M double sided tape around the edges of the glass inside. You could even leave the back paper covering the double-sided tape (making it well.. single sided). Glue may be too "permanent" a solution.
Get yourself an air duster (compressed air in a can), some 2mm 3M double-sided tape (I like that one the best and it's cheap), a set of precision screwdrivers and a plastic prying tool (if you don't wanna buy one, improvise with anything that can do the trick, so long as it's plastic. Metal can break parts very easily).
I've had my new S21 for a few hours now, and I keep finding more and more strips of the protective plastic that needs to be peeled off . Does anyone make a special light which make this plastic fluoresce? Could be a great new product!
LOL, I agree.
If I recall correctly, think I found the two big obvious sheets covering the back plastic and the screen glass. Another smaller sheet covering the camera bump and lenses. Then two (three?) very skinny separate strips wrap the circumference of the phone (the metal frame). One starts just to the right of the bottom speaker grill and runs up to the power/volume buttons. Another strip from but button around the top of the phone. And a third strip from the left of the SIM card and up the left-hand side frame. The strips along the circumference are hard to see or feel, and you need to find the start/end of the strip in order to begin peeling it off. I used my fingernail to find each end-point, then picked at the end until it came free enough so I could grab and pull up the entire strip.
I hope I found them all as I've put the phone into a Samsung leather case, which fits so snugly I can barely get it back out.
Leave it be and case it.
Without a case it only a matter of time until it self destructs.
As the protective film works its way loose remove so grit that gets trap under it doesn't mar the phone's finish. Otherwise it helps to protect from case marring.
Leave the display factory protector on as long as possible until it degrades.