Used msm downloader on BE88CB BE2028 model to revert back to stock rerouted with magisk and installed Twrp after updating and I think something went wrong with my persist img
Related
Hi.
Since install the magisk work found for Android pay and pokemon go I noticed the fingerprint scanner has stopped working. I'm wondering if this is related to a possible tamper flag showing? So where can I find a copy of stock recovery to flash it over twrp and see if that fixes the issue ?
Thanks
So I did a stupid, installed stock rom via TWRP and then installed the OTA. Now my phone will only boot into TWRP, I've tried recovering my LineageOS backup and wiping all and installing stock rom again but nothing boots past TWRP.
I have the UK model and can't find stock nougat to flash with fastboot commands, can anybody help?
Edit - I just flashed 7.0 RETMX and it seems to work fine, this can be deleted.
Anybody can PLEASE share, need it or my phone is destroyed coz i accidentally destroyed my backup
EDIT:
FOUND OUT A SOLUTION
- FLASHED boot.img FROM B130 FIRMWARE
- STILL BOOTLOOPED
- FLASHED MAGISK 13.3 WHICH MODIFIES THE BOOT.IMG
- BOOT LOOP AGAIN
-AFTER 4 BOOTLOOPS HUAWAI RESCUE DOING FACTORY RESET
>>>Sucesful boot into ANDROID
-----------------------------
NOW ONLY STUCK BY ENTERING PIN ----> DOESN'T ACCEPT MY PIN
Hello, i've got a similar problem. after trying to flash emui 5.1 supersu.zip the phone bootlooped. after restroring with twrp backup the phone crashed after the "emui-registration/welcome" dialog. tried to flash b130 via twrp and dload method. do you have any ideas? maybe by flashing boot.img? and where can i find the b130 boot.img? Thx!
4r44444 said:
Anybody can PLEASE share, need it or my phone is destroyed coz i accidentally destroyed my backup
EDIT:
FOUND OUT A SOLUTION
- FLASHED boot.img FROM B130 FIRMWARE
- STILL BOOTLOOPED
- FLASHED MAGISK 13.3 WHICH MODIFIES THE BOOT.IMG
- BOOT LOOP AGAIN
-AFTER 4 BOOTLOOPS HUAWAI RESCUE DOING FACTORY RESET
>>>Sucesful boot into ANDROID
-----------------------------
NOW ONLY STUCK BY ENTERING PIN ----> DOESN'T ACCEPT MY PIN
Click to expand...
Click to collapse
I extracted it with Huawei Update Extractor from UPDATE.APP provided in this thread "https://forum.xda-developers.com/honor-9/how-to/firmware-honor-9-stf-l09c432-b130-2017-t3649673" (you must extract update.app from firmware and than use huawei update extractor windows app to extract the extracted UPDATE.APP - I only extracted the boot image... phone booted succesful, had to do another hard reset via TWRP coz it didn't accept my (right!) PIN... now works... only fingerprint scanner and navbar buttons does not work... now I only need the BOOT.IMG from my old firmware (B100) and flash via bootloader... I think this will fix the problem....
I do not guarantee this things to work maybe crushing your device even more do it only if you risky
So I currently have USA Hawaii mate 10 pro on 9.0.0264 BL unlocked and magisk patched ramdisk and I keep getting notification to install the .267 update but it will not install due to the patched ramdisk so I just want to flash back to stock, I have downloaded the full ota through Hawaii hisuite application and its in zip format, so how do i flash this zip to go back to stock, thank you.
lingarajug said:
So I currently have USA Hawaii mate 10 pro on 9.0.0264 BL unlocked and magisk patched ramdisk and I keep getting notification to install the .267 update but it will not install due to the patched ramdisk so I just want to flash back to stock, I have downloaded the full ota through Hawaii hisuite application and its in zip format, so how do i flash this zip to go back to stock, thank you.
Click to expand...
Click to collapse
You don't have to flash the whole update, just extract the recovery_ramdisk from 9.0.0.264 firmware (use Huawei Extractor to do that) and flash it with fastboot.
Another way to get the stock recovery it's to use Partitions Backup by Wanam (from Playstore), in its options enable the "raw partition image" and backup "erecovery_ramdisk".
Copy the backup on PC and flash it with this fastboot command :
fastboot flash recovery_ramdisk erecovery_ramdisk.img
Note: replace "erecovery_ramdisk.img" with the filename of the image that you backed up previously.
After flashing the stock recovery_ramdisk, you can install the official OTA.
I am confused, there is recovery_ramdis and erecovery_ramdisk and which one is it.
Update- i just flashed recovery_ramdis and then system from ota and i am updated now. Thank you.
So i had a hickup with updating magisk to v20.3.
The result was that after a reboot the device got stuck in fastboot mode.
I went to TWRP 3.3.0 recovery and backed up all offered partitions before then attempting to re-flash magisk.
Didn't work out.
Then i heard that if you extract the boot.img from the stock firmware and flash it with fastboot you can get back to a working state where you can install Magisk again.
So i thought.
Now after booting i am greeted by the miui first install wizard and the whole set of apps seems to be gone as well as my settings.
IIRC i only removed the dalvik cache which shouldn't affect this state.
Where in the procedure is the mistake and can i get the old pre-broken update state back? I am afraid something has been lost in the process
selemine said:
So i had a hickup with updating magisk to v20.3.
The result was that after a reboot the device got stuck in fastboot mode.
I went to TWRP 3.3.0 recovery and backed up all offered partitions before then attempting to re-flash magisk.
Didn't work out.
Then i heard that if you extract the boot.img from the stock firmware and flash it with fastboot you can get back to a working state where you can install Magisk again.
So i thought.
Now after booting i am greeted by the miui first install wizard and the whole set of apps seems to be gone as well as my settings.
IIRC i only removed the dalvik cache which shouldn't affect this state.
Where in the procedure is the mistake and can i get the old pre-broken update state back? I am afraid something has been lost in the process
Click to expand...
Click to collapse
Just install the latest stock rom then install recovery and restore all the backed up partitions.
Now install magisk and reboot.
If that doesn't work (u get into fastboot again) then just flash the boot.img file via fastboot and then reboot.
if i restore the backed up partitions and install magisk over it i get back to the non-booting , stuck in fastboot version. So something is wrong in the state of denmark.
selemine said:
if i restore the backed up partitions and install magisk over it i get back to the non-booting , stuck in fastboot version. So something is wrong in the state of denmark.
Click to expand...
Click to collapse
I looked at the /data backup from twrp and it is only 3mb, unless stuff got moved to /system or so, it seems to be gone forever.
Hell , i wil never update magisk again.
selemine said:
I looked at the /data backup from twrp and it is only 3mb, unless stuff got moved to /system or so, it seems to be gone forever.
Hell , i wil never update magisk again.
Click to expand...
Click to collapse
Don't install magisk with the rom, just restore the data, flash the stock boot.img file and then reboot.
After boot uninstall the magisk manager app and reboot to recovery and then flash magisk again.