Hi!
i have a p20 lite smartphone and nothing work. the screen is black and i tried to reboot to press on long and also to press the volume up / down to recovery mode. nothing happens
when i connect it to my windows pc i see in de device manager a HUAWEI USB COM 1.0 device.
so is it possible to reflash it and to repair my phone?
when yes how?
please send me links to the necessary software.
thx
Related
In this case, there is my friend phone.
i wanna help him to UBL(Unlock Boot Loader) and after that update to MIUI 8.
but before update to miui8,the phone is hardbrick because fault at trying for UBL.(un official i've tried)
red led notif always blinking no gap,, all keys combined no effect.
open back cover and try to remove battery socket,try to connect it again,,turning on,try many times,, always fault.
almost frustrated,,
Trying to flash it always unknown and appear ''Qualcomm HS-Diagnostic 900E''
and using DFC(deep flash cable) not effect.:crying:
Searching around and found any methode and i combine it. :laugh:
step..
1. follow this Disable Driver Signature Enforcement in Windows 7/8/10 64-Bit
" i choose at booting PC i push F8 repeatly and choose Disable Driver Signature Enforcement, enter"
2. un instal and re instal usb driver
3. ''remove battery socket''
4. open MIFLASH and located at your true ROM to flash/update
open ''device manager'' in your PC, to know it connected correctly or not.
5.push volume - and volume + and hold on,,(don't push power button) while conect usb to PC. it must show at device manager
''Qualcomm HS-USB QDLoader 9008'' and leave it.
refresh at MIFLASH,when device detected and you can flash it until done.
if still show ''Qualcomm HS-Diagnostic 900E'' , you must try step 2 and then 5 until right connection.
foila,,:good: the phone is back..:laugh:
'sorry for the bad english'
i hope it will help your pain.. :victory:
I was using miui pro and I flash Miui multi pro via twrp.
After complete installed rom reboot my phone.
but it is not open.
I try to power on but can't.
Try to open recovery mod via power +volume button but can't.
It's like phone power Off and can't power on.
Pls help me.
Try to flash via Xiaomi tools.
It find com port when I select location of flash files and click flash it failed after 40 second. Error flashing.
Totally no response of my phone when I press power button.
I just installed miui multi pro rom via red wolf.
And it's finished install.
I press reboot.
And the problem create.
Why and what the solution.
your phone is dead,just buy new one and problem can fixed,thanks
Is your booting in bootloader if yes flash fastboot rom
mohsinreadymoney said:
Is your booting in bootloader if yes flash fastboot rom
Click to expand...
Click to collapse
No
Phone power Off and can't go to fastboot mod
mohsinreadymoney said:
Is your booting in bootloader if yes flash fastboot rom
Click to expand...
Click to collapse
When I connect charger or USB with pc just notification light beep on/off nothing show on display.
Maybe your bettery dead. Plug it in charging for 2 hours, otherwise replace the battery.
Bro... Mera v aysa ho chuka hai .. agar charger or data cable plug in krne pr red light blink krta h to.. sbse phle back cover remove or battry ki wire ko disconnect kro or PC se connect kro .. fir mi flash tool se flash kro. Automatic EDL me aa jata h phone .. you can try this method..
Mizanur0001 said:
When I connect charger or USB with pc just notification light beep on/off nothing show on display.
Click to expand...
Click to collapse
1. Is it red light beeping ON/OFF?
2. What does the COM port say after connecting the phone to the PC in device manager? HS-USB diagnostics 900E or Downloader?
3. In either way install the Qualcomm HS-USB Downloader driver if not installed in your PC
4. Get ready to pull off the back cover watching youtube, it's not so difficult, disconnect the battery for 20s. Then reconnect. Next connect the cable to the PC to check if it connects in Download mode or not
hello guys , need very much your all help to get up ( resurect?) my phone
i was flashing this ROM https://forum.xda-developers.com/ma...nt/rom-emui-8-0-kangvip-mate-10-lite-t3784834
and installed their kernel and tuning camera p20 pro , installation was finished, then i wiped cache and clicked button Reboot , and ....................... nothing till now, Black screen , buttoms not respons , was trying clicking and still nothing
Black screen
buttons dosent responds , volume up and down , and power
i trying with connecting cabble , TWRP , recovery and other stuffs.. nothing
any suggests ?
xydonis said:
hello guys , need very much your all help to get up ( resurect?) my phone
i was flashing this ROM https://forum.xda-developers.com/ma...nt/rom-emui-8-0-kangvip-mate-10-lite-t3784834
and installed their kernel and tuning camera p20 pro , installation was finished, then i wiped cache and clicked button Reboot , and ....................... nothing till now, Black screen , buttoms not respons , was trying clicking and still nothing
Black screen
buttons dosent responds , volume up and down , and power
i trying with connecting cabble , TWRP , recovery and other stuffs.. nothing
any suggests ?
Click to expand...
Click to collapse
Does pc recognize phone?
Fastboot is working?
If pc recognize phone as usb-ser there is no fix.....
Enviado de meu BLA-L29 usando o Tapatalk
ChaseRxx said:
Does pc recognize phone?
Fastboot is working?
If pc recognize phone as usb-ser there is no fix.....
Enviado de meu BLA-L29 usando o Tapatalk
Click to expand...
Click to collapse
Fastboot not,
when i connect phone to pc there is only sound of windows ( alert of new device , mass storage ) but there is no any other windows information , MY PC dosent see phone and SD Card
phone completly dead ? what shall i do ?
xydonis said:
Fastboot not,
when i connect phone to pc there is only sound of windows ( alert of new device , mass storage ) but there is no any other windows information , MY PC dosent see phone and SD Card
phone completly dead ? what shall i do ?
Click to expand...
Click to collapse
How does the device appear in Device Manager
Enviado de meu BLA-L29 usando o Tapatalk
ChaseRxx said:
How does the device appear in Device Manager
Enviado de meu BLA-L29 usando o Tapatalk
Click to expand...
Click to collapse
not showing in device manager , its like ghost mode , only sound from Windows playing Device Connect Sound thats all
Hello.
I have the same problem on my Mate 10 Lite, after flashing firmware i have a black screen and when i connect phone to pc it shows me "fastboot 2.0" and i can working with fastboot.
Reset of the phone is working too because when is connected to computer and i`m pushing power+vol up windows is showing reconnected but when reset is finished still is in fastboot mode but i don`t see it on screen because is black.
Can i do something with that ? Maybe huawei service is needed? My phone is dead and still has warranty - i think…..
wojtekml said:
Hello.
I have the same problem on my Mate 10 Lite, after flashing firmware i have a black screen and when i connect phone to pc it shows me "fastboot 2.0" and i can working with fastboot.
Reset of the phone is working too because when is connected to computer and i`m pushing power+vol up windows is showing reconnected but when reset is finished still is in fastboot mode but i don`t see it on screen because is black.
Can i do something with that ? Maybe huawei service is needed? My phone is dead and still has warranty - i think…..
Click to expand...
Click to collapse
I listened about dc phoenix, but it cost money for flash firmware with and without bootloader unlocked, it cost 15 euros for 72 hours after the initial flashing, maybe it works or no, i don't know exactly but good luck if you test it!
Ok phone back to me from huawei client center and has replaced battery with screen and mainboard….. has a new imei and its a new mate 10 lite.
At this time i have only rooted system and trwp recovery installed.
And i`m waiting for roms to flash by twrp.
Best regards
Hey, I need Some help ASAP, I am in a Big trouble. So The whole scenario is that I decided to install the Paranoid Android 11 in my Mi A3 and After Unlocking the Bootloader, I changed the Boot Slot from A to B and Flashed the Twrp file ( to the boot ) and Pressed the Power and Volume down Button, The Phone turned off and is not turning on Not Even the Fastboot Logo, Its Bricked. (Here are some additional Points Which you Should Know, 1. I checked the ports on my Computer and It was Showing Qualcomm HS-USB QDLoader 9008 So I think the phone is in EDL mode. 2. I tried to Flash Mi A3 Stock Firmware using Miflash and It was Showing Error "Cannot receive hello Packet") The Phone is my Daily Driver and If anyone can, Please help me Fix this.
Even I got the same issue after downloading the latest Android 11, then got rectified the Mobile through the nearest service center.
Globally many people experienced the same issue.
Now it is ok !
use qfile and service rom
set up in ufs mod
plug off battery and connct usb with short test point
load files 0/1/2/3/4/5 and
elprfesor said:
use qfile and service rom
set up in ufs mod
plug off battery and connct usb with short test point
load files 0/1/2/3/4/5 and
Click to expand...
Click to collapse
could you explain it more?
I also dead briked my phone after install a11 and used qfil to flash some stuff in edl mode using test points,
I recommend using the right qualcomm driver 32 or 64 bits like your OS and also reboot after install driver,
I don't recommend open the back painel bcs even u doing it right it don't close well after bcs lose stickiness,
If u can just go to a service, they can manage with this better then u.
Same here. Even opened the back cover to touch the EDL points.
Tried getting out of that mode by flashing to stock ROM using the Mi Flash Tool as I'm getting a weird error, `Input string was not in the correct format`. even when using the very same input as I've seen on a YouTube Tutorial & I had also tried it out on the very same version of Flash Tool (and still got the error)
Hi,
My BLA-L09 (Mate 10 Pro) is bricked due to a bad firmware update. I have a black screen, I cannot enter any mode (recovery, fastboot). But when I plug/unplug the phone, Windows detects it. I've downloaded (and paid some credits) DC-Phoenix. Now the phone is detected as a USB COM 1.0 device since I've installed the driver as explained here https://www.dc-unlocker.com/flash-bricked-huawei-phones-in-huawei-1-mode. With Dc-Phoenix, I can boot into fastboot mode thanks to testpoint mode. But my problem is that everytime I leave fastboot mode, the phone screen turn to black (like if it's shut down).
I guess my board software is broken, so I would lilke to re-install a fresh board software (via testpoint fastboot mode using Dc-Phoenix), but unfortunatelly, I cannot find a place to download board software for BLA-L09.
Anyone knows where we can find board software for BLA-L09?
Is there another way to unbrick my phone? Considering I can go in fastboot mode, I hope there is still a chance!
iBen68 said:
Hi,
My BLA-L09 (Mate 10 Pro) is bricked due to a bad firmware update. I have a black screen, I cannot enter any mode (recovery, fastboot). But when I plug/unplug the phone, Windows detects it. I've downloaded (and paid some credits) DC-Phoenix. Now the phone is detected as a USB COM 1.0 device since I've installed the driver as explained here https://www.dc-unlocker.com/flash-bricked-huawei-phones-in-huawei-1-mode. With Dc-Phoenix, I can boot into fastboot mode thanks to testpoint mode. But my problem is that everytime I leave fastboot mode, the phone screen turn to black (like if it's shut down).
I guess my board software is broken, so I would lilke to re-install a fresh board software (via testpoint fastboot mode using Dc-Phoenix), but unfortunatelly, I cannot find a place to download board software for BLA-L09.
Anyone knows where we can find board software for BLA-L09?
Is there another way to unbrick my phone? Considering I can go in fastboot mode, I hope there is still a chance!
Click to expand...
Click to collapse
Take a look at my GDrive Folder
Btw latest DC provides software testmode and hard brick recovery...