Related
When i try to connect the phone to a flash mode via usb cable (holding the back boton and conneckting the cable at the same time) the phone just go into offline charging mode? A try other pc over usb cable not helps?
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode,
the question is, what are you trying to do ?
Flashing using Flash tool ? if so you have to follow the steps of flashing, 1st use the flash tool and when it says "turn off your phone and then hold you back button while plug the usb cable in" then you are suppose to do it !
zmbutt said:
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode,
the question is, what are you trying to do ?
Flashing using Flash tool ? if so you have to follow the steps of flashing, 1st use the flash tool and when it says "turn off your phone and then hold you back button while plug the usb cable in" then you are suppose to do it !
Click to expand...
Click to collapse
Yes dats am trying to do. The drivers is instaled 100% Wen a hold the back boton and connekt the usb cable the green light flashes one time and den noting the pfone goes into offline charging mode. http://www.youtube.com/watch?v=_v3MjErfhug&feature=plcp
the cable is too long :O
use the latest flash version,
turn off the phone, take out the battery for 30 seconds and then try again.
zmbutt said:
the cable is too long :O
use the latest flash version,
turn off the phone, take out the battery for 30 seconds and then try again.
Click to expand...
Click to collapse
1 I'm tray with 3 other seuss original cables nothing changes
2 at the moment i'm with the latest
3 dont helps
it seems like, Flash tool cannot communicate with your phone, and the only thing which need to check is "Driver" you need to recheck the correct drivers for flash tool !
zmbutt said:
it seems like, Flash tool cannot communicate with your phone, and the only thing which need to check is "Driver" you need to recheck the correct drivers for flash tool !
Click to expand...
Click to collapse
On the 3 pc were im trying do to it the drivers are 100% good and the flash tool to. With the original SEUS program seus-update the results are the same? For me this is a hardware problem with the phone ? I'm using the trivers with comes with flash tool.
Turn off your firewall and antivirus
mpiekp said:
Turn off your firewall and antivirus
Click to expand...
Click to collapse
10x but the this don't helps
zmbutt said:
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode
Click to expand...
Click to collapse
Actually, no, it's not.
Green led should light and no offline charge should start.
Yes but the green light only 1 time flashes for 1 sek and disappears. Then the phone is going to offline charging mode..
any ideas what to do ?
REPAIR YOUR X 10I
FILES YOU NEED::http://www.mediafire.com/download/tdg4dho2bwq6fg5/X10i_3.0.1.G.0.75_only%20kernel_baseband.ftf
http://www.mediafire.com/download/vy4v24ditk4lsxa/Xperia_X10i_3.0.1.G.0.75_GLOBAL-GGL_GENERIC_1232-9897.rar
http://www.mediafire.com/download/0pgnz7iy2yq4iae/FlashTool_0.2.9.1-GBready_root_xRec.exe
INSTRUCTIONS IS HERE
http://forum.xda-developers.com/showthread.php?t=2570671
PLEASE BEFORE YOU START PUT YOUR PHONE ON CHARGER 3-4 HOURS
PRESS THANX IF HELPED
I tried using your solution but every time I failed to connect my X10 to flash mode. Unplug the USB, take out put back the battery of my phone, press the back button on the phone and plug in USB but nothing comes out and just showing 19/025/2013 04:25:24 - INFO - Searching Xperia....
19/025/2013 04:25:24 - ERROR - Please plug you device in flash mode many many times. My phone battery was fully charge with 5 hours. Any solutions with this?
answer
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
noob hacker said:
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
Click to expand...
Click to collapse
I tried this before but still can't connect my phone to flash mode.
Hikigaya Hachiman said:
I tried this before but still can't connect my phone to flash mode.
Click to expand...
Click to collapse
send me a phone,I will fix it and sent you back.....write me message pm
noob hacker said:
send me a phone,I will fix it and sent you back.....write me message pm
Click to expand...
Click to collapse
I think i can't send you because im at Malaysia and thats not my phone.
some questions
Hikigaya Hachiman said:
I think i can't send you because im at Malaysia and thats not my phone.
Click to expand...
Click to collapse
Hi,
I have some confirmation questions:
Which ROM ftf do you have, which was the original baseband on the phone? Maybe check in STOCK ROM list for a better suited ROM.
I have better experiences when connecting the other way round: plug the cable into the phone and connect either at the computer or into a short usb-extender cable in convenient reach.
When doing it the other way round, I have often 'timing problems' to fiddle the usb micro into the socket at the phone.
Maybe try another cable and/or carefully press the plug to the phones frontside to prevent connection problems.
Alexej
NO Fastboot, No Recovery mode only EDL is accessible.
Qualcomm HS-USB QDLoader 9008 is detected. Tried flashing Global Dev Rom and Global Stable Rom. But Same problem... NO FastBoot, No Recovery
Please Help
asett3 said:
NO Fastboot, No Recovery mode only EDL is accessible.
Qualcomm HS-USB QDLoader 9008 is detected. Tried flashing Global Dev Rom and Global Stable Rom. But Same problem... NO FastBoot, No Recovery
Please Help
Click to expand...
Click to collapse
could you please explain more, about what u have actually done...?
edit:-
some helpful things you may try .
*hoping you are running windows7,8,10(64bit) try usong mi flash tool beta..if on32 bit os use layest mi flash tool..
*install pda net,and adb drivers
*disable driver enforcement in windows.
*make sure phone is detected in miflash tool..(just click refresh button to see whether phone is detected in mi flash tool..
*use latest fastboot rom (you can see link for kenzo in guide section,just go through old posts)
adithyan25 said:
could you please explain more, about what u have actually done...?
edit:-
some helpful things you may try .
*hoping you are running windows7,8,10(64bit) try usong mi flash tool beta..if on32 bit os use layest mi flash tool..
*install pda net,and adb drivers
*disable driver enforcement in windows.
*make sure phone is detected in miflash tool..(just click refresh button to see whether phone is detected in mi flash tool..
*use latest fastboot rom (you can see link for kenzo in guide section,just go through old posts)
Click to expand...
Click to collapse
Thanks for your support. I am using Win 10-64Bit, Mi Flash Beta, Detecting phone without any issue flashing is also done successfully. But after that it is still on EDL mode
asett3 said:
Thanks for your support. I am using Win 10-64Bit, Mi Flash Beta, Detecting phone without any issue flashing is also done successfully. But after that it is still on EDL mode
Click to expand...
Click to collapse
Press power button about 10-20 seconds
[email protected] said:
Press power button about 10-20 seconds
Click to expand...
Click to collapse
Tried but not booting.... Also tried combination pwr+vol-/ (pwr)+(vol-) / (pwr)+(vol-) / (pwr)+(vol-)+(vol-) ..........
Still in EDL Red led Blinking while charging and connected to PC. (9008)
asett3 said:
Tried but not booting.... Also tried combination pwr+vol-/ (pwr)+(vol-) / (pwr)+(vol-) / (pwr)+(vol-)+(vol-) ..........
Still in EDL Red led Blinking while charging and connected to PC. (9008)
Click to expand...
Click to collapse
some clarifications needed
*did you replaced any file especially the bootloader file to unlock the unofficial way.
*kenzo/kate?
*did you try booting into fastbokt mode by connection phone to pc(pow+vol down)
adithyan25 said:
some clarifications needed
*did you replaced any file especially the bootloader file to unlock the unofficial way.
*kenzo/kate?
*did you try booting into fastbokt mode by connection phone to pc(pow+vol down)
Click to expand...
Click to collapse
Kenzo,
Officially Unlocked
Fastboot Mode not working
Power + Vol Down no respond :,(
Some ppl told me I was saying sh** but even with a fully working ROM my vol down never came back.
My story is kinda similar to yours, if I do remember, disconnect battery + deep flash cable made de trick (http://en.miui.com/thread-365090-1-1.html)
bigbrother69 said:
Some ppl told me I was saying sh** but even with a fully working ROM my vol down never came back.
My story is kinda similar to yours, if I do remember, disconnect battery + deep flash cable made de trick (http://en.miui.com/thread-365090-1-1.html)
Click to expand...
Click to collapse
But my pc is detecting Qualcomm HS-USB QDLoadar 9008 and i can flash via mi flashtool.
asett3 said:
Kenzo,
Officially Unlocked
Fastboot Mode not working
Power + Vol Down no respond :,(
Click to expand...
Click to collapse
probabaly you will have to disconnect battery and reconnect it again.. and flash rom using deep flash cable..(either make one or buy it online ,refer youtube if u wanna make one)
adithyan25 said:
probabaly you will have to disconnect battery and reconnect it again.. and flash rom using deep flash cable..(either make one or buy it online ,refer youtube if u wanna make one)
Click to expand...
Click to collapse
Same not powering on aftr successful flash
Please Help someone
Did you try to flash battery disconnected, deep flash cable connected, push button on, release, connect battery, push power button..
I mean every combinaison possible with those stuff...I really thought mine was dead during at least a month so...hope is still permitted..
bigbrother69 said:
Did you try to flash battery disconnected, deep flash cable connected, push button on, release, connect battery, push power button..
I mean every combinaison possible with those stuff...I really thought mine was dead during at least a month so...hope is still permitted..
Click to expand...
Click to collapse
tried gave it to service center!
mobile pc co conect rakho apne aap reboot ho jayega automatic
Bro plz tell me ur contact number nd my number 7340329575 plz call me im helf u
---------- Post added at 08:18 PM ---------- Previous post was at 08:14 PM ----------
asett3 said:
NO Fastboot, No Recovery mode only EDL is accessible.
Qualcomm HS-USB QDLoader 9008 is detected. Tried flashing Global Dev Rom and Global Stable Rom. But Same problem... NO FastBoot, No Recovery
Please Help
Click to expand...
Click to collapse
Bro tell me ur contact number nd my contact number 7340329575 plz call me my number im helf u
Did u find any solution?
I have also experiencing this problem. Back in MIUI 8, when I'm totally running out of battery, the phone won't charge or getting into any mode
Try to
"Hold Vol- + Connect the phone to PC USB Slot"
Let me know if it works
Try TWRP flashing
As you said that the mi flash tool is detecting your phone so try flashing the twrp recovery by the edl method and then you can flash the rom
Refer this link for Flashing TWRP
youtu.be/rCONN1_IPuU(please add https:// before the link )
And after flashing process is done and of you are unable to access the internal storage then complete wipe the internal storage and you are good to go
Just disconnect battery, connect EDL cable (deep flash cable with pressed button), run MiFlash and flash the phone.
I have been having the same problem recently
My Moto e2 is unlocked and doesn't work when it isn't connected to the charger
As soon as I remove the charging pin it gets switched off and I'm unable to power it up.
But when I plug in the charging cable it immediately lights up and is stuck in bootloop
It shows the bootloader screen and restarts again everytime
I'm able to go into the fastboot menu, but whenever I select any option other than barcodes it goes into the same bootloop.
In the fastboot menu it doesn't even show the device as connected when I use a data cable.
I tried charging it overnight. No use. It was stuck in the same bootloop till the next day
Please help
lsandmanl said:
I have been having the same problem recently
My Moto e2 is unlocked and doesn't work when it isn't connected to the charger
As soon as I remove the charging pin it gets switched off and I'm unable to power it up.
But when I plug in the charging cable it immediately lights up and is stuck in bootloop
It shows the bootloader screen and restarts again everytime
I'm able to go into the fastboot menu, but whenever I select any option other than barcodes it goes into the same bootloop.
In the fastboot menu it doesn't even show the device as connected when I use a data cable.
I tried charging it overnight. No use. It was stuck in the same bootloop till the next day
Please help
Click to expand...
Click to collapse
Flash stock full firmware.(not rom)
Using fastboot or mfastboot
The device shows the status : Not Connected in the menu
Any option other than barcodes cause the device to reboot again
Pankaj Rai said:
Flash stock full firmware.(not rom)
Using fastboot or mfastboot
Click to expand...
Click to collapse
The device shows the status : Not Connected in the menu
Any option other than barcodes cause the device to reboot again
lsandmanl said:
The device shows the status : Not Connected in the menu
Any option other than barcodes cause the device to reboot again
Click to expand...
Click to collapse
Change usb cable (or try in other pc)
Check whether Motorola drivers installed correctly or not.
Pankaj Rai said:
Change usb cable (or try in other pc)
Check whether Motorola drivers installed correctly or not.
Click to expand...
Click to collapse
The same thing has started on my Xiaomi redmi 1s Armani
Can you please guide me
lsandmanl said:
The same thing has started on my Xiaomi redmi 1s Armani
Can you please guide me
Click to expand...
Click to collapse
Ok,
1.download Mi Flash Tool
2.install drivers for 1s
3.download stock firmware for 1s
3.Connect your phone in fastboot mode (using original usb cable)
4.select firmware and flash
Hope this will help you
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
gustavoabonare said:
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
Click to expand...
Click to collapse
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Archit9169 said:
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Click to expand...
Click to collapse
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
gustavoabonare said:
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
Click to expand...
Click to collapse
Forget about warranty, get it checked at a local store.
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
---------- Post added at 04:27 AM ---------- Previous post was at 04:26 AM ----------
I have faced this too ,3 months ago , you just need to open the case and then unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Deep flash cable
Try flashing after removing the battery like Aditya said it worked on my friends phone.
[email protected] said:
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Click to expand...
Click to collapse
Thx man, will try when I get back from work
balazs312 said:
Deep flash cable
Click to expand...
Click to collapse
It's already in EDL 9008 mode, I used the test point. Don't know if the DFC will do anything different, but will try it anyway if the way Aditya told me don't work
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
[email protected] said:
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
Click to expand...
Click to collapse
Hey man, didn't work, I disconnected the battery as you said and still got the error when I tried to flash. I downloaded the last rom available from xiaomi site (kenzo_global_images_V9.5.3.0.MHOMIFA_20180405.0000.00_6.0_global_7b6353b764), but still nothing.
I guess it's the EMMC chip alright ;x, but thx anyway
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
[email protected] said:
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
Click to expand...
Click to collapse
Already tried, didn't work, but thx anyways man
Just plug it in to a wall charger. I had the same issue even after edl flash miui rom but charging it fixed my problem. Follow these steps.
1- plug it in
2- ignore the red led blinking
3- wait for 5 min.
4- it will boot.
5- if doesn't, I'm sorry