When i try to connect the phone to a flash mode via usb cable (holding the back boton and conneckting the cable at the same time) the phone just go into offline charging mode? A try other pc over usb cable not helps?
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode,
the question is, what are you trying to do ?
Flashing using Flash tool ? if so you have to follow the steps of flashing, 1st use the flash tool and when it says "turn off your phone and then hold you back button while plug the usb cable in" then you are suppose to do it !
zmbutt said:
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode,
the question is, what are you trying to do ?
Flashing using Flash tool ? if so you have to follow the steps of flashing, 1st use the flash tool and when it says "turn off your phone and then hold you back button while plug the usb cable in" then you are suppose to do it !
Click to expand...
Click to collapse
Yes dats am trying to do. The drivers is instaled 100% Wen a hold the back boton and connekt the usb cable the green light flashes one time and den noting the pfone goes into offline charging mode. http://www.youtube.com/watch?v=_v3MjErfhug&feature=plcp
the cable is too long :O
use the latest flash version,
turn off the phone, take out the battery for 30 seconds and then try again.
zmbutt said:
the cable is too long :O
use the latest flash version,
turn off the phone, take out the battery for 30 seconds and then try again.
Click to expand...
Click to collapse
1 I'm tray with 3 other seuss original cables nothing changes
2 at the moment i'm with the latest
3 dont helps
it seems like, Flash tool cannot communicate with your phone, and the only thing which need to check is "Driver" you need to recheck the correct drivers for flash tool !
zmbutt said:
it seems like, Flash tool cannot communicate with your phone, and the only thing which need to check is "Driver" you need to recheck the correct drivers for flash tool !
Click to expand...
Click to collapse
On the 3 pc were im trying do to it the drivers are 100% good and the flash tool to. With the original SEUS program seus-update the results are the same? For me this is a hardware problem with the phone ? I'm using the trivers with comes with flash tool.
Turn off your firewall and antivirus
mpiekp said:
Turn off your firewall and antivirus
Click to expand...
Click to collapse
10x but the this don't helps
zmbutt said:
That's the normal condition if you plug the usb cable in while holding the back button, it will go into offline charging mode
Click to expand...
Click to collapse
Actually, no, it's not.
Green led should light and no offline charge should start.
Yes but the green light only 1 time flashes for 1 sek and disappears. Then the phone is going to offline charging mode..
any ideas what to do ?
Related
Hello,
I isntalled that rom with kernel. http://forum.xda-developers.com/showthread.php?t=2391858. and the problem is now that my pc, cant see my phone, i tried every method i found on the site. i instaled all drivers and reinstaled from flashtool like 10 times, and my pc still doesnt see device. while i try to connenct via fasboot. i have the violet light for like 2 sekonds and after it the device starts to boot normally, same is with flashboot. flash tool does not give any msg of connecting a device. can any tell a way to get it working? i want to flash to stock soft. but i cant cause nothing sees the device with installed drivers.
FOrogot to ad that i flashed the aospa rom, cause i thought i will get usb working atlast. but im stuck now on com.android.phone stopped working, and i cant even download any other rom using phone:
EDIT
Just read in nemesis kernel topic "* Computer/PC Companion and even Flash Tool cannot detect.". so Any ideas how can i flash it. without have any other rom on sd card? I will be rlly happy if someone can help me, i know i made a big mistake but not doin recovery, first time i not did and all went wrong.
do u have SUS? (Sony Update Service)
try connecting with SUS if SUS don't detect your phone then flashtool will not detect your phone also.
Well it doesnt not see to, In my opinion no porgram will see it if device manager cant see it, but now after some slleep i got and idea. Could it be maybe the problem of to old micro usb cable. because my got broken. and i have to use from my sister that has samsung wave.
Good Luck.
LED should be blue not violet for fastboot.
Make sure the phone is shut down first, press volume up + power for 10-15 seconds untill you feel 3 vibrations.
Well whatever coulour it is violet or blue. I press the volume up connect the phone to usb. And i got this coulur for 2-3 second and then it goes to charging mode. it happens every time. Same happens to flashboot. Green for 2-3 sec and the it goes to charging mode.
maebara said:
Well whatever coulour it is violet or blue. I press the volume up connect the phone to usb. And i got this coulur for 2-3 second and then it goes to charging mode. it happens every time. Same happens to flashboot. Green for 2-3 sec and the it goes to charging mode.
Click to expand...
Click to collapse
It's not "whatever" if it's violet it means it's waiting for vol- to enter CWM and not entering fastboot.
Make sure the phone is turned off as I explained.
Phone is turned of, I allways wait for those 3 vibrations before i begin the process. And here to enter the cwm is blue, and for fastboot i have violet. If i had a camera i would record it to prove it.
maebara said:
Phone is turned of, I allways wait for those 3 vibrations before i begin the process. And here to enter the cwm is blue, and for fastboot i have violet. If i had a camera i would record it to prove it.
Click to expand...
Click to collapse
Flashtool and PCC worked before on the same PC?
What do you see in flashtool log when you connect in fastboot and flash mode?
ChikeD said:
Flashtool and PCC worked before on the same PC?
What do you see in flashtool log when you connect in fastboot and flash mode?
Click to expand...
Click to collapse
THey say nothing, As i say in the first post. PC does not see the device, Flastool handles as nothing has been conected. same device manager on wondows. no poop outs that drivers are missing, or anything.. Fastboot has allways waiting for device, doesnt matter how much i try to onnect. It worked before. I tried on other laptop but its same. Thats why later i wrot that maybe this cable is to old for that phone. But it works for other phones.
maebara said:
THey say nothing, As i say in the first post. PC does not see the device, Flastool handles as nothing has been conected. same device manager on wondows. no poop outs that drivers are missing, or anything.. Fastboot has allways waiting for device, doesnt matter how much i try to onnect. It worked before. I tried on other laptop but its same. Thats why later i wrot that maybe this cable is to old for that phone. But it works for other phones.
Click to expand...
Click to collapse
Your USB did not work before?
ChikeD said:
Your USB did not work before?
Click to expand...
Click to collapse
I got my orginal mircro usb from xperia but it went boroken last time, on monday i go buy me new. but i wanted to use my sis micro usb from samsung wave, well mirco usb is micro usb imo, but i can be wrong. before i was able to do things on that cable too. but now idk if its the cable fault. or its phone, cause seems i can only charge my phone throught it. even on pc. it only charges nothing more. I just want to know if there is any way to make phone visible to pc, installing drivers, reseting. wiping data on phone, nothing works
maebara said:
I got my orginal mircro usb from xperia but it went boroken last time, on monday i go buy me new. but i wanted to use my sis micro usb from samsung wave, well mirco usb is micro usb imo, but i can be wrong. before i was able to do things on that cable too. but now idk if its the cable fault. or its phone, cause seems i can only charge my phone throught it. even on pc. it only charges nothing more. I just want to know if there is any way to make phone visible to pc, installing drivers, reseting. wiping data on phone, nothing works
Click to expand...
Click to collapse
It could be the connector on the phone.
I use samsung cable no problem, the Sony that came with XP is still sealed
REPAIR YOUR X 10I
FILES YOU NEED::http://www.mediafire.com/download/tdg4dho2bwq6fg5/X10i_3.0.1.G.0.75_only%20kernel_baseband.ftf
http://www.mediafire.com/download/vy4v24ditk4lsxa/Xperia_X10i_3.0.1.G.0.75_GLOBAL-GGL_GENERIC_1232-9897.rar
http://www.mediafire.com/download/0pgnz7iy2yq4iae/FlashTool_0.2.9.1-GBready_root_xRec.exe
INSTRUCTIONS IS HERE
http://forum.xda-developers.com/showthread.php?t=2570671
PLEASE BEFORE YOU START PUT YOUR PHONE ON CHARGER 3-4 HOURS
PRESS THANX IF HELPED
I tried using your solution but every time I failed to connect my X10 to flash mode. Unplug the USB, take out put back the battery of my phone, press the back button on the phone and plug in USB but nothing comes out and just showing 19/025/2013 04:25:24 - INFO - Searching Xperia....
19/025/2013 04:25:24 - ERROR - Please plug you device in flash mode many many times. My phone battery was fully charge with 5 hours. Any solutions with this?
answer
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
noob hacker said:
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
Click to expand...
Click to collapse
I tried this before but still can't connect my phone to flash mode.
Hikigaya Hachiman said:
I tried this before but still can't connect my phone to flash mode.
Click to expand...
Click to collapse
send me a phone,I will fix it and sent you back.....write me message pm
noob hacker said:
send me a phone,I will fix it and sent you back.....write me message pm
Click to expand...
Click to collapse
I think i can't send you because im at Malaysia and thats not my phone.
some questions
Hikigaya Hachiman said:
I think i can't send you because im at Malaysia and thats not my phone.
Click to expand...
Click to collapse
Hi,
I have some confirmation questions:
Which ROM ftf do you have, which was the original baseband on the phone? Maybe check in STOCK ROM list for a better suited ROM.
I have better experiences when connecting the other way round: plug the cable into the phone and connect either at the computer or into a short usb-extender cable in convenient reach.
When doing it the other way round, I have often 'timing problems' to fiddle the usb micro into the socket at the phone.
Maybe try another cable and/or carefully press the plug to the phones frontside to prevent connection problems.
Alexej
My phone is on version S124. It is dead right now. Only red light shows when connected to charger and it turns of after some time.
This problem happened before also, I took it to Lenovo service center, they did something and my phone was back on. It is out of warranty, I had to pay for servicing. This has happened again, how can I fix it at my home?
I have SP flash tools, S124 ROM and Windows 7 PC.
Thanks.
NexR said:
My phone is on version S124. It is dead right now. Only red light shows when connected to charger and it turns of after some time.
This problem happened before also, I took it to Lenovo service center, they did something and my phone was back on. It is out of warranty, I had to pay for servicing. This has happened again, how can I fix it at my home?
I have SP flash tools, S124 ROM and Windows 7 PC.
Thanks.
Click to expand...
Click to collapse
Reflash your firmware!
In development section you will find some good tutorials!
Here is one link!
http://forum.xda-developers.com/lenovo-p780/development/rom-lenovo-p780-pre-rooted-official-t2553725
stympy said:
Reflash your firmware!
In development section you will find some good tutorials!
Here is one link!
http://forum.xda-developers.com/lenovo-p780/development/rom-lenovo-p780-pre-rooted-official-t2553725
Click to expand...
Click to collapse
Hi stympy!
I tried that exact thing at first. The problem is it does not recognize my phone on connecting via USB cable. Drivers were correctly installed as I could successfully flash firmware few days before. Now when I connect it to PC via USB cable, it does not show up in device manger, nor is it recognized by SP flash tool (stuck at Searching). Red LED turns on connecting to USB on PC/Power. I have tried all USB ports on my PC and also tried different USB cables.
I have also tried the "plug-in then reset via button on back" method. Not working.
Any idea what's going on?
NexR said:
Hi stympy!
I tried that exact thing at first. The problem is it does not recognize my phone on connecting via USB cable. Drivers were correctly installed as I could successfully flash firmware few days before. Now when I connect it to PC via USB cable, it does not show up in device manger, nor is it recognized by SP flash tool (stuck at Searching). Red LED turns on connecting to USB on PC/Power. I have tried all USB ports on my PC and also tried different USB cables.
I have also tried the "plug-in then reset via button on back" method. Not working.
Any idea what's going on?
Click to expand...
Click to collapse
Hi. Try this:
Uninstall curent drivers.
Reboot computer or laptop.
After reboot open device manager window
Look om ports area on device manager
Plug the phone now
Something with MTK69XX should appear.
If this appear you are on the good track.
If not tell me and we look for something else!
stympy said:
Hi. Try this:
Uninstall curent drivers.
Reboot computer or laptop.
After reboot open device manager window
Look om ports area on device manager
Plug the phone now
Something with MTK69XX should appear.
If this appear you are on the good track.
If not tell me and we look for something else!
Click to expand...
Click to collapse
OK, tried this. When I plug in a device, like my printer, or my other android phone, Device manager window automatically refreshes device list. This does not happen when I plug-in my p780.
I was using miui pro and I flash Miui multi pro via twrp.
After complete installed rom reboot my phone.
but it is not open.
I try to power on but can't.
Try to open recovery mod via power +volume button but can't.
It's like phone power Off and can't power on.
Pls help me.
Try to flash via Xiaomi tools.
It find com port when I select location of flash files and click flash it failed after 40 second. Error flashing.
Totally no response of my phone when I press power button.
I just installed miui multi pro rom via red wolf.
And it's finished install.
I press reboot.
And the problem create.
Why and what the solution.
your phone is dead,just buy new one and problem can fixed,thanks
Is your booting in bootloader if yes flash fastboot rom
mohsinreadymoney said:
Is your booting in bootloader if yes flash fastboot rom
Click to expand...
Click to collapse
No
Phone power Off and can't go to fastboot mod
mohsinreadymoney said:
Is your booting in bootloader if yes flash fastboot rom
Click to expand...
Click to collapse
When I connect charger or USB with pc just notification light beep on/off nothing show on display.
Maybe your bettery dead. Plug it in charging for 2 hours, otherwise replace the battery.
Bro... Mera v aysa ho chuka hai .. agar charger or data cable plug in krne pr red light blink krta h to.. sbse phle back cover remove or battry ki wire ko disconnect kro or PC se connect kro .. fir mi flash tool se flash kro. Automatic EDL me aa jata h phone .. you can try this method..
Mizanur0001 said:
When I connect charger or USB with pc just notification light beep on/off nothing show on display.
Click to expand...
Click to collapse
1. Is it red light beeping ON/OFF?
2. What does the COM port say after connecting the phone to the PC in device manager? HS-USB diagnostics 900E or Downloader?
3. In either way install the Qualcomm HS-USB Downloader driver if not installed in your PC
4. Get ready to pull off the back cover watching youtube, it's not so difficult, disconnect the battery for 20s. Then reconnect. Next connect the cable to the PC to check if it connects in Download mode or not
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
gustavoabonare said:
Hey, i have a Xiaomi Note 3 Pro Kenzo and one day he just turned off and never went back again. When i plug it on pc, it just shows black screen, flashes the red light multiple times and it's recognized as Qualcomm HS-USB Diagnostics 900E.
I've already searched online and seems that my phone is stuck on EDL mode, so I made it go to the real EDL mode that allows me to flash it a new rom. I managed to make my pc recognize as Qualcomm 9008.
Beeing that, I tried to flash a rom but at the mi flash 20160330 it gets stuck on: "send nop command" forever and at the mi flash 2170425 it gets the error : "<?xml version="1.0" encoding="UTF-8" ?><data><log value="init storage:fail " /></data> "
I've got another redmi note 3 pro, and I can flash it, so I don't there's any problem with my computer, but the info is:
Windows 10 Pro 64x
Safe Drivers Disable
If anyone can help...
Click to expand...
Click to collapse
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Archit9169 said:
Seems like a problem with the emmc chip. Get the device checked to make sure that your emmc is not faulty. If the emmc is safe, contact me and I'll help. Until then good luck.
Click to expand...
Click to collapse
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
gustavoabonare said:
Thx for the reply man, the problem is that i live in Brazil, we don't have Xiaomi assistance, so I don't have a place to get it checked ;x.
But yeah, I saw in other forums that this migth be a EMMC problem
Click to expand...
Click to collapse
Forget about warranty, get it checked at a local store.
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
---------- Post added at 04:27 AM ---------- Previous post was at 04:26 AM ----------
I have faced this too ,3 months ago , you just need to open the case and then unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Deep flash cable
Try flashing after removing the battery like Aditya said it worked on my friends phone.
[email protected] said:
I have faced this too ,3 months ago , you just need to open the case and then remove the unplug the battery cable then flash the fastboot ROM ,yes the PC will give give enough power to flash ,you must not replug the battery while flashing ,now when the flash is don't unplug the USB cable and put it in charger by hitting power button for 8 secs it will not charge then immediately replug the the battery cable then again press the power button for 8 sec till it reboots ,boom your system will boot
Click to expand...
Click to collapse
Thx man, will try when I get back from work
balazs312 said:
Deep flash cable
Click to expand...
Click to collapse
It's already in EDL 9008 mode, I used the test point. Don't know if the DFC will do anything different, but will try it anyway if the way Aditya told me don't work
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
[email protected] said:
I should explain you fully
1)removing battery will keep the phone in edl mode but it will solve your error of mi flash is mi flash will successfully flash the fastboot ROM ,remember you need to first remove the battery cable then insert phone ,no light will blink but it will be recognized as qsp loader port in your PC ,don't worry
2) after successfully completing the first step flash the complete fastboot ROM ,it should go success
3)now don't replug the battery cable now ,do nothing ,just insert cherger and press power button as long as the screen don't turn on ,when it will turn on the battery bar wouldn't go up, then without removing the charger cable from phone ,insert battery, you will see that battery is still not charging, nothing to worry this was just to turn the display on ,now again press the power button for 10 to 14 sec so that the device reboot and boom your phone will start charging and after you can successfully boot into system and use your phone.
4)this is if you still cannot successfully flash using mi flash tool just unplug all a the cable which you see after opening back case don't worry you just have to open the cables which you see ,you don't have to unplug those cables in which you have to open screws etc .
Hope this will help you
Click to expand...
Click to collapse
Hey man, didn't work, I disconnected the battery as you said and still got the error when I tried to flash. I downloaded the last rom available from xiaomi site (kenzo_global_images_V9.5.3.0.MHOMIFA_20180405.0000.00_6.0_global_7b6353b764), but still nothing.
I guess it's the EMMC chip alright ;x, but thx anyway
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
[email protected] said:
Bro sorry that I couldn't help but can you please try unpluging the cable as shown in the figure and then try to flash using mi flash tool if it still even don't help sorry bro
Unplug the cable given in figure and then try to flash using mi flash , if the device is not detected then replug that cable and and then try to flash if it still don't help sorry bro
Click to expand...
Click to collapse
Already tried, didn't work, but thx anyways man
Just plug it in to a wall charger. I had the same issue even after edl flash miui rom but charging it fixed my problem. Follow these steps.
1- plug it in
2- ignore the red led blinking
3- wait for 5 min.
4- it will boot.
5- if doesn't, I'm sorry