In the XDA connetors section of this site the pinout is listed for making an IPAQ 36xx --> XDA adapter.
Do you need to connect to all the pins mentioned or just one?
For Example for GND, do I need to connect all of the pin nos. 2, 5, 16, 17 & 18 from the XDA side to both of the pins nos. 4 & 10 on the IPAQ side? Or just any of the XDA (GND) pins to any of the IPAQ (GND) pins?
Thanks.
I would just use one or two. If you're not charging through it, that should be fine...
Related
This message contains all postings in this thread
dated before January 19th 2003
Subject: XDA to IPAQ converter
From: Joe_PDA
Date: 14 Jan, 2003 22:15:19
Can someone list the correct pin to pin combinations for a
converter plug that allows me to use my IPAQ 3600 series
accesories on my XDA.
I've already got the 22 pin end (to XDA) and 12 pin end (to IPAQ
3600 Accessories) in a plastic housing, and I think I know which
pin number is which on each end.
I just need to know what pin numbers from the 22 pin side to
attach to which pin numbers on the 12 pin side.
Subject: Pinouts iPaq and XDA
From: XDA developers
Date: 15 Jan, 2003 00:23:43
The XDA pinouts are on our connectors page:
http://xda-developers.
com/connectors
The 12-pin iPaq pinout is at:
http://www.kh-gps.de/ipaq.htm
Subject: Okay I'm half way there....!
From: Joe_PDA
Date: 15 Jan, 2003 03:37:05
X Thanks for the reply. So exactly which pin from the 12 pin
side would go to which pin of the 22 pin side. Could you lay it
out for me?
I have seen on my trawls of the net a converter/ adapter.
Connect one end to the XDA.
Connect the other end to the iPaQ accesory. From memory it was only US$20. Not sure about getting that in Europe though.
Would depend on your requirements whether this would be of any use.
But imagine getting a gamepad hooked up!!!!
mMf
I got a few more requests for cable layouts, so I provided cable pinouts for both serial cables (to computer and to peripherals) as well as conversion cables between XDA on one side and both old (12-pin) and new (22-pin) iPaq accessories on the other.
http://xda-developers.com/connectors
Does anyone know how to modif the IPAQ 3600->3800 series adapter, made by Think Outside (or Targus), to work as an IPAQ 3600 --> XDA adapter? The ribbon cable has only 4 wires. Is it possible to adjust the wiring in the ribbon cable, or is it necessary to rewire the connectors? Can anyone figure this out?
As I would like to connect my serial GPS receiver to the XDA in the car I'm trying to source an All in one cable that would provide me with both serial and power connections for the XDA.
I would prefer somthing that has the cigar lighter style plug with associated voltage regulator built in, although if that is not available I could build the regulator myself.
GPS cable
I am just about to embark on this project myself. I have a Garmin GPS III and already have their car power/PC Serial cable.
I got the pinouts for the GPS unit from the Garmin site, and it looks like only TXD, RXD and GND are required. This should make it fairly easy to connect up to the xda, following the pinouts on this site. I'm off to Maplin today to try and get a male 9pin serial and an xda connector, following which I shall get the soldering iron out. The tricky bit will be getting the power from the Garmin cable as well. I'll let you know how I get on.
Failing that, you could try MobilePlanet, a US site that seem to specialise in GPS connectors. However, they make a cable that only supplies power to the PDA, and the GPS has to run on batteries. The link below should take you to the xda/Garmin GPS page. There's another page on the site that covers Magellan receivers.
http://www.pc-mobile.net/gpswp.htm
rgds,
Alex.
Hi Alex 10x for reply,
My main problem is trying to source the XDA plug, one that has not been moulded, so that the power/data cables can be fitted.
Jim
http://www.gomadic.com/ipconplug38s.html
i have a spare usb cable for hp6340 and no cable for my new spv m2000.
i want to transorm this cable and to make it work for the spv m2000. but i don't know wich wires to swithc or what to modify
i need some help please.
email at [email protected] me or reply here
http://wiki.xda-developers.com/wiki/Connectors
i save the xda pinout but i dont have stupid hp 6300 pinout
i save the xda pinout but i dont have stupid hp 6300 pinout
Orez at the base of the page on wiki you will see the ipaq equivalent pins, doesnt that help?
Also look here.
http://www.kolumbus.fi/ari.torpstrom/pinouts.htm
iPAQ H6300 series cradle connector pinout:
Pin out 22 Pin Cradle Connector iPAQ side.
1 V_ADP
2 V_ADP
3 V_ADP
4 V_ADP
5 Reserved – Do Not Use
6 Reserved – Do Not Use
7 Serial RXD
8 Serial TXD
9 Reserved – Do Not Use
10 GND
11 Reserved – Do Not Use
12 Serial RTS
13 Serial CTS
14 Reserved – Do Not Use
15 GND
16 No Connect – Do Not Use
17 USB Detect
18 No Connect – Do Not Use
19 USB – UDC +
20 No Connect – Do Not Use
21 USB – UDC -
22 GND
Shell tied to GND
cruisin-thru thx a lot man
cruisin-thru thx a lot man, i made it work
I buyed an mhl hdmi cable but its pin connecting to phone(s2 gt i9100) ( phone slot of usb) is larger than the charger and usb pin so its not fits inside the slot I cant view a single thing on tv l..I buyed it for rs 3000 ( indian money) its original built by samsung made in korea.... its connects with a note3 tested by father by his friends note3.. iam not so rich...is there any way connect to s2 by dicreasing length or something.....plz help me...
Sent from my GT-I9100 using XDA Premium 4 mobile app
No buy one for i9100 "you're model"
I found a small adapter that coverts 5 pin to 11 pin used for mhl cable is there any cable that converts 11 pin to 5 pin avaolable...?
Sent from my GT-I9505 using XDA Premium 4 mobile app