hi there, i hav an o2 xda 2, that i managed to flash to 1.72 rom, but now i would like to sell it so i tried to flash it back to the original o2 rom (with all the o2 interface etc) and i get an error message saying "ERROR 100: MODEL ID " and then it all stops, so now i hav an xda2 with a blank screen, that says serial at the top and v1.03 at the bottom in red. windows picks up that the device is there wen i dock it but i cant drag any files on to it at all. im completely stuck now havnt got a clue how to get it back to how it was, all i want is it to be back to normal. can anyone help? cheers
OK. Try this:
1. Press Power+Navi-key+reset in one time (you will be in bootloader - that screen with Serial 1.03, if you put it into cradle, it will change to USB 1.03)
2. Kill ActiveSync in Windows (wcescomm.exe process) using Task Manager
3. Put XDA2 into cradle
4. Run the update again
HTH
Related
Hi ,
I had 1.72.00wwe on my phone but i was tryin 2 upgrade it further but it got stuck while upgrading and its showing seril while not on cradle and while on cradle its showing usb 1.06
plz hlp me iam newbee and not good in programmin .I also have asecond Xda2 with 1.66.00wwe plz tell if it can b of any help
Reset your device, place it in the cradle and re-run the upgrade.
thanx i tried it already from 2 computers in one its showing error 103 no rom image found and in another its showing error 101 country code problem
Which ROM are you attempting to upgrade to? Which one exactly had you previously upgrade to? What operator do you use?
I'm asking all this to try and get a better picture. Normally, people in your situation can recover by applying the same upgrade again, or, at worst, re-applying the one they are upgrading from.
Make sure you are in bootloader mode (by pressing Jog button and Power button at the same time as pressing reset) before retrying any upgrade. Also make sure the USB cradle is plugged directly into a USB port on your PC and not through a hub and that the power supply is connected to the cradle. It may help to make sure that Activesync isn't running also.
active sync
in the active sync tray it shows that not connected
Well i had 1.72.00wwe rom image 1.14 earlier and iwas tryiong to upgrade to 1.72. something can't remember exactly but it was with rom image 1.17 it was downloaded from t mobile and my current phone is from o2
Click to expand...
Click to collapse
Activesync is not needed for upgrades. The upgrade process looks after its own connection. I suggest you follow the procedures in my post here to overcome the Country ID error problem. You will need to know what the device's operator and language IDs are currently set to, which is why I asked you above. I suspect you won't have Devicedata.txt, so it becomes necessary to know what operator and language the previous upgrade was.
to revive your XDA2 again
The main point is what is ROM 1.66 come from (e.g. i-mate ot T-mobile)
If you doesn't upgrade 1.66 ROM by yourself or it came from factory ,you must tell us which operator did you buy from.
If you try upgrade across operator ,it will hang on boot loader screen.
And again, which 1.72 ROM did you try to upgrade from?
I tried to do a ROM Upgrade but something went wrong and now the screen on my XDA II just shows the words Serial and v1.06. When I did a hard reset the screen still shows the same thing. When I connect the device using the cradle the word Serial changed to USB, but it didn't seem to connect to the PC. The Activesync was not activated also. When I tried to run the ROM Upgrade again, it shows ERROR 100: MODEL ID ERROR. I tried to run HimaUpgradeUT_noID.exe, it shows Error 103: ROM IMAGE FILE NOT FOUND. Can anyone please help me get my device working again? Thank you in advance.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
[email protected] youre own risk.
Dead XDA II
Hi Guys, I'm new to all this because my XDA has never failed me, until now. I too tried to upgrade the ROM, realising too late that the upgrade from a UK site was not meast for the Asian zone.
Anyway, I tried downloading the following link:
http://rapidshare.com/files/36498840...adeUt_noID.rar runterladen.
When I tried to lanch the file it tells me that RUU.dll is missing.
Is there a link that works or is there a fix for this? As I said, I'm new to this therefore need step by step instruction.
Hope someone can assist, I'm lost without my XDA II.
Thank you
Ben
cannot download from the link
hello
I have a black screen on my qtek 2020i (XDA2i) after upgrading the ROM, and I saw that the solution you are providing works good, but I cannot download the fix using the link
please advice
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar
XDAII Dead
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
m1000 dead sad
i regreat to say i did try for update my spv m1000 today but my got died now when i tried i did conntect my ppc with ppc via bluetooth actvesync when i run HimaUpgradeUt.exe then a window open and shows mgs wait 30 minunt but after even 1 minunt got error also my phone got stop like dead and screen shows on top serial and on bottom it shows v1.3 i realy .sad. becouse now i cant reeboot also even ui have not data cable any body help me plz what i do now ?
thanks for my help
really want to say thanks who helpd me i upgraded now my spv m1000 my self without any problem becouse i brought data cable of i mate and its workin fine with my spv m1000 yahooooooooo xda roken
usman_hussain1987 said:
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
Click to expand...
Click to collapse
Hi Usman,
What OS of windows PC do you use? it can't work with windows vista. Try to downloads new version of active sync then try it again. The upgrade is specify, can't work in any kind of devices
Hi, Excuse me if this has been answered already but I couldn't find it if it has!
I'm trying to upgrade my M3100 to WM6 - Schaps 4.31. I've unlocked the phone and installed Hard SPL v7. When it goes through the Schaps upgrade, I get to the final 'next' button, press it and then the progress bar appears. The M3100 screen goes blank, activesync closes and then the upgrade hangs. Then a Error 260 conection message comes up and, after a few minutes, the M3100 bursts into life.
I've tried resetting the PC and the M3100 with no sucess. I am using Activesync 4.5 & Windows XP SP2
Any help is appreciated. Thanks.
Phil
Try disabling all firewalls, it may be worth trying to flash using the SDCard method. This is a very common issue I'm sure if you search the forum for 260 you will find loads of entries.
Also have a read of this which should help you.
http://forum.xda-developers.com/showthread.php?t=299462
The official Orange M3100 ROM (and probably most official ROMs) comes with a doc which explains all of the error numbers and what to do.
My suggestion would be to do the following as you'll be told to try this before looking further into it:
instead of connecting to ActiveSync and running the update .exe file, do this:
Disconnect device from desktop PC altogether;
Open ActiveSync;
Go into File > Connection Settings and UNcheck the 'allow USB' option - odd as that may seem;
Put your Hermes into bootloader mode (press and hold left-side 'ok' button and right-side 'power' button whilst soft-resetting with stylus), seeing tri-colour screen and the word 'Serial';
When in tri-colour screen, with 'Serial' displayed, THEN connect device to desktop PC via USB cable, even though you've disabled USB connections;
'Serial' will change to 'USB' on the tri-colour screen;
Run the update from Schap's or whoever.
Hopefully that will have worked. Good luck, mon ami.
Chunkymonkey, Progress I think....
Bootloader screen comes up but now I get 1% progress on the update and then Error 244 Invalid Model ID.
For info - bootloader screen reads:-
IPL-1.04
SPL-2.10 Olipro
Thanks
pbunn said:
Chunkymonkey, Progress I think....
Bootloader screen comes up but now I get 1% progress on the update and then Error 244 Invalid Model ID.
For info - bootloader screen reads:-
IPL-1.04
SPL-2.10 Olipro
Thanks
Click to expand...
Click to collapse
Invalid Model ID?
Although you have Olipro's clever rework of SPL on (good), have you also Super-CIDed your M3100?
chunkymonkey said:
Invalid Model ID?
Although you have Olipro's clever rework of SPL on (good), have you also Super-CIDed your M3100?
Click to expand...
Click to collapse
I thought I had - I tried a Vodafone SIM card in it and it worked. I'll do it again to be sure.
Phil
Chunkeymonkey,
Used HTC Hermes SIM & CID Unlock - v3a to Super-CID - I still get the error 244 Invalid ID....
Phil
are you connecting thru a usb hub/multi port,if so dont,,,,,, only connect thru a direct usb connection
pbunn said:
Chunkeymonkey,
Used HTC Hermes SIM & CID Unlock - v3a to Super-CID - I still get the error 244 Invalid ID....
Phil
Click to expand...
Click to collapse
Odd. Should only do that when the Hermes believes the ROM you're using isn't meant for it.
Can't remember if the Super-CID happens automatically with the SIM-unlock using that tool or if it is optional. If it was optional, might want to make sure it actually IS super-CID as you might just be sim-unlocked maybe.
To check CID status use mtty.exe. Put your phone into bootloader, disable USB connections in ActiveSync on desktop PC (File > Connections > Disable USB connections) and then plug Hermes to PC. Run mtty and type task 32. Response "Level=0xFF" means it's NOT Super-CID. Response "Level=0" means it IS Super-CID.
Came back with "level=0" but still no joy flashing the rom.
I'm trying to upgrade my M3100 to WM6 - Schaps 4.31. I've unlocked the phone and installed Hard SPL v7. When it goes through the Schaps upgrade, I get to the final 'next' button, press it and then the progress bar appears. The M3100 screen goes blank, activesync closes and then the upgrade hangs. Then a Error 260 conection message comes up and, after a few minutes, the M3100 bursts into life.
I've tried resetting the PC and the M3100 with no sucess. I am using Activesync 4.5 & Windows XP SP2
Click to expand...
Click to collapse
I had exactley the same problem with my M3100.
Try using a different USB port on your PC. Don't what the difference was but it worked for me.
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
pbunn said:
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
Click to expand...
Click to collapse
probably would have been worth loading 4.31 WWE. Very stable and fast.
pbunn said:
Re downloaded Schaps_WM6Pro_Hermes_4.30_WWE_Full.exe and all seems to work OK. Not sure if there was an issue in the original download but it all looks cool now.
Click to expand...
Click to collapse
Nice one mate
Now gone to version 4.31 and the phone skin has gone back to the old style.
Do you know where I can get the updated one from? Is there a cab file available?
if you go to --> Start > Settings > Today it should show a list of themes you can apply. just select one and press 'ok'. sorry if this isnt what u mean
raggers said:
if you go to --> Start > Settings > Today it should show a list of themes you can apply. just select one and press 'ok'. sorry if this isnt what u mean
Click to expand...
Click to collapse
Raggers,
No that's not what I mean. In version 4.30 there was a different phone pad tothe one I have with version 4.31 - it has gone back to a wm5 type. Also - there is no 'Airplane' mode in connection manager that allows me to turn everthing off in one hit.
Hello Professionals (0:
Sorry for my bad English, German was better (o;
My HTC S740 / Rose starts suddenly no more.
It starts always new after the new "smart mobility" screen
= Loop
Do you have a solution without having to send to HTC?
BTW: When I try to flash I get the error message:
"invalid vendor id"
although it is actually an original HTC device is.
Thank you for your help (o:
What ROM are you trying to flash? The ROM is probably for some other branded S740.
To flash this ROM anyway you can use QMAT to generate goldcard and flash it (extracted ROSEIMG.nbh) from card...
interessting! can you post some link or how-to ?! i realy want to try it
Hello.
I have the same problem.
I have S740 with wrong downloading soft.
When I try to load new ROM into my S740 after 1% downloading the Smartphone ROM Upadate Utlility 3.27.4.3 show ERROR [294]: INVALID VENDER ID.
I don't know what will be before.
How can I solve this problem?
I will be very very grateful.
Rgds.
Read the stickies. You need HardSPL.
Could you tell me step by step what I should do?
1. Activesync doesn't see phone.
2. When I turn on the phone (using data cable) is only black screen SMART MOBILITY and restart and restart ect ect.
3. I downloaded RUU_Rose_Orange_UK_1.17.61.2_Radio_sign_12.29.30.09_0.29.30.22_Ship and I copied RUU_signed.nbh into the microSD card.
4. I changed the name from RUU_signed.nbh to RoseIMG.nbh
5. I turned on the phone one more time, and put button VOL DOWN
6. Then we can see info LOADING, next CHECKING and next info 0028002 NOT ALLOWED
7. Then I can see screen red, green, blue and below is white part with info: USB
8. On this screen is also:
ROSE100
SPL-1.54.0000
MicroP-Rose (LED) v10
MicroP-Rose (KEY) v5
PCBID 0x80
RID 0x0
9. Activesync still doesn't see phone.
10. When I try to use ROMUpadateUtility after 1% I see ERROR [294]: INVALID VENDER ID.
11. I used older and new versions of ROMUpdateUtility and always is the same problem.
So could you tell me step by step what can I do?
Thank you for help!!!
Now I know more.
I tried to connect via Activesync and download new HardSPL, but there was no connection between S740 and Activesync. I used 2 comps, 2 different data cables and without any progress.
Seems that phone is without ROM now.
Connecting without microSD card is good. I turn on the phone, push VOL DOWN and I see boot menu with the SERIAL info. When I put data cable I can see USB.
So all seems to be correct.
But how to download HardSPL without Activesync?
I have no connection between phone and Acitesync so I can not download HardSPL. I use Rose-S740-HardSPL-Kit-by-jocky2001, hope that it is correct SPL.
OK, so I tried to install nand android on my htc hd2 and firstly I installed hspl 3 on it then as instructions said I updated ROM version to MAGLDR ... And now phone is frozen right after I turn it on it only shows me O2 welcome message. Please don't tell me that it is coz the phone is locked to o2 network because there r so many threads and no one mentioned that u can't install android if the phone is locked or I missed something SO any help pls? I am freaking out that my phone is dead.
RAM 512
ALso:
When I press a red button near the sim card while holding volume down and it shows 3 colour screen and connect it to the pc , pc does make a sound as phone was recognised but it doesnt come up with any windows or anything that I could see that phone is there.. Is there any way I can install old rom or smthing to get my poor phone back, please help me, I am not experienced in this at all and first attempt failed
Put the phone into BootLoader mode. At the bottom of the screen you will see 'Serial'. Now plug it into your computer and the 'Serial' changes to 'USB' - you have made a good connection to the computer. The computer doesn't recognise it as a phone, because the phone firmware has not been booted up, so don't wory about it.
Run the O2 ROM form the computer. One of the conditions is that you have made an ActiveSync connection, just tick the box and proceed.
Once the ROM has flashed, it is advised to do a hard reset, but I have never had a problem not doing it.
Now you are back to the begining.
You are getting a little mixed up between Operator (SIM) Locked and Firmware Locked. They are independant of each other. You can SIM unlock your phone, which means you can use any telecom's SIM card in your phone even though the phone boots up with an O2 logo. You can unlock the firmware (HSPL) so that you can use the stock HTC ROM (not the 3.14 version) or one of the excellant custom ROMs, now the phone won't show any of the O2 stuff but you are still limited to using O2 SIM cards.
Now you have to Run HSPL2 and select the SPL 2.08.HSPL. Since you want to run Android NAND you have to flash a .50 RADIO - try the 2.15.50.14 RADIO.
I would have a real good read * HERE *. And if you want to go ahead, the read it again.