All,
I just move in to UK from Far East Asia. I have an Asian XDAII and successfully crashed it in an attempt to upgrade the ROM to latest UK-O2 version.
The screen is blank and show only a note reads "SERIAL". It won't connect to my PC for synchronization at all.
Is there anyway to fix this?
Thanks for the help.
Steve
Sure, try to upgrade again...
1. Put it in the cradle (it will change to USB)
2. Run the update again...
Related
Hya
I tried to downgrade my MDAII from the ROM 1.72 to ROM 1.66.
But after downgrading it, it looks like my MDA II is dead now...
It doesnt do anything anymore
Now I got a white screen with upper writing "SERIAL"
and down "V1.03" and no backlight at all...
Can somebody help/guide me how to fix my device?
I'm a newbee and need yoru help
Many thanks.
'Serial' just means that its trying to communicate in Serial mode, if you drop it onto the dock/charger (assuming that is connected to your PC) the word 'Serial' should change to 'USB'. If it does then try the downgrade again.
VW_ELM said:
I tried to downgrade my MDAII from the ROM 1.72 to ROM 1.66.
But after downgrading it, it looks like my MDA II is dead now...
Click to expand...
Click to collapse
Don't worry, it's not dead. If the downgrade process completed normally, you just need to do a hard reset (press power button while holding stylus in reset hole). If this doesn't help, the downgrade failed.
The most likely reason is that you connected the cradle to a USB hub. Try connecting it directly to your PC, then perform the flash procedure again.
Another possibility is that you used Windows 95/98/ME. Some users have reported problems. Try the flash procedure from a Windows 2000/XP system again.
Hope this helps!
Daniel
nope it doesn't work, i've got the same problem!
Don't know what to do...
Thanks tadzio: B4 l have same problem Rom failure , and l try to reinstall
again, flash Rom now :lol:
I post a original latest belgian rom on this forum (rom from dangard), try to install this version.
http://forum.xda-developers.com/viewtopic.php?t=8403&postdays=0&postorder=asc&start=75
you need to dowload this file (a shortcut) on your pc, then execute it following the procedure.
Bye
I solved the problem for me:
With HimaUpgradeUt.exe there was no connection. It was a too old version (0.5.0.0).
So I replaced it with Version 0.6.0.0 and it runs !!!
Hi ,
I had 1.72.00wwe on my phone but i was tryin 2 upgrade it further but it got stuck while upgrading and its showing seril while not on cradle and while on cradle its showing usb 1.06
plz hlp me iam newbee and not good in programmin .I also have asecond Xda2 with 1.66.00wwe plz tell if it can b of any help
Reset your device, place it in the cradle and re-run the upgrade.
thanx i tried it already from 2 computers in one its showing error 103 no rom image found and in another its showing error 101 country code problem
Which ROM are you attempting to upgrade to? Which one exactly had you previously upgrade to? What operator do you use?
I'm asking all this to try and get a better picture. Normally, people in your situation can recover by applying the same upgrade again, or, at worst, re-applying the one they are upgrading from.
Make sure you are in bootloader mode (by pressing Jog button and Power button at the same time as pressing reset) before retrying any upgrade. Also make sure the USB cradle is plugged directly into a USB port on your PC and not through a hub and that the power supply is connected to the cradle. It may help to make sure that Activesync isn't running also.
active sync
in the active sync tray it shows that not connected
Well i had 1.72.00wwe rom image 1.14 earlier and iwas tryiong to upgrade to 1.72. something can't remember exactly but it was with rom image 1.17 it was downloaded from t mobile and my current phone is from o2
Click to expand...
Click to collapse
Activesync is not needed for upgrades. The upgrade process looks after its own connection. I suggest you follow the procedures in my post here to overcome the Country ID error problem. You will need to know what the device's operator and language IDs are currently set to, which is why I asked you above. I suspect you won't have Devicedata.txt, so it becomes necessary to know what operator and language the previous upgrade was.
to revive your XDA2 again
The main point is what is ROM 1.66 come from (e.g. i-mate ot T-mobile)
If you doesn't upgrade 1.66 ROM by yourself or it came from factory ,you must tell us which operator did you buy from.
If you try upgrade across operator ,it will hang on boot loader screen.
And again, which 1.72 ROM did you try to upgrade from?
just need ideas
as my xdaII is ****ed
i have now many choices to play with
game starts.... :x
i cant flash radio rom to my O2xdaII
it hangs on o2 splash screen wit nogsm message
itried already all verions except winows2003se
i dont know how to flash with sd card
as i dont have sd card but i have mmc card
thanks and regards
dun think you can flash the 1.03--> 1.06 BL
sa any one knows how to flash boot loader
could you be more precise, as in:
1. What was the directory contents when you started your upgrade
2. What did your devicedata file say before the upgrade?
3. What are the operator id & language of the NBF files?
4. Did you previously upgrade?
i dont know i got unit in totally dead condition
with mmc card and some rom image
Reflashing
Hello everyone, hope you're having a good Xmas.
I have the same problem but it's partly of my own making. I was upgrading my O2 XDA II to the lastest ROM (obtained from O2 website) and my laptop went into sleep mode after 46% of the upgrade was complete. Now all I have is the O2 blue screen. Soft and hard resets do nothing.
I did backup all my data (which I'm not sure includes the OS) to SDIO before starting the update and don't know if I can recover from that.
I will need to send it back to have it re-flashed if I can't find a solution but any advice you guys can give would be most welcome. At the moment my PC can't see the usb connected XDA and there's no activity on the XDA screen.
Thanks for your support people!
I tried to do a ROM Upgrade but something went wrong and now the screen on my XDA II just shows the words Serial and v1.06. When I did a hard reset the screen still shows the same thing. When I connect the device using the cradle the word Serial changed to USB, but it didn't seem to connect to the PC. The Activesync was not activated also. When I tried to run the ROM Upgrade again, it shows ERROR 100: MODEL ID ERROR. I tried to run HimaUpgradeUT_noID.exe, it shows Error 103: ROM IMAGE FILE NOT FOUND. Can anyone please help me get my device working again? Thank you in advance.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
Wrong ID
a few days ago i had the same problem with my HTC Blue Angel (also known as
qtek 9090)
temporaly youre PDA shows the bootloaderscreen. On top it shows youre kind of connection, on the bottom you can find the revision of this piece of software.
try this tool to reanimate youre pda.
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar runterladen.
extract this file into the dir, where you have copied the original ROM-Image from youre developer, put youre PDA into cradle and check, if the status of this connection is changed in USB. Everything o.k? Right now: doubleklick on MAUpgradeUT_NoID and drink a coffee. it takes about 10 Minutes and after this youre pda runs as well. dont forget to copy youre original ROM-Image with the original Installer after finishing this procedure to avoid any errors.
Well, i hope this tutor will help you. i´m interested for.
[email protected] youre own risk.
Dead XDA II
Hi Guys, I'm new to all this because my XDA has never failed me, until now. I too tried to upgrade the ROM, realising too late that the upgrade from a UK site was not meast for the Asian zone.
Anyway, I tried downloading the following link:
http://rapidshare.com/files/36498840...adeUt_noID.rar runterladen.
When I tried to lanch the file it tells me that RUU.dll is missing.
Is there a link that works or is there a fix for this? As I said, I'm new to this therefore need step by step instruction.
Hope someone can assist, I'm lost without my XDA II.
Thank you
Ben
cannot download from the link
hello
I have a black screen on my qtek 2020i (XDA2i) after upgrading the ROM, and I saw that the solution you are providing works good, but I cannot download the fix using the link
please advice
http://rapidshare.com/files/36498840/MaUpgradeUt_noID.rar
XDAII Dead
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
m1000 dead sad
i regreat to say i did try for update my spv m1000 today but my got died now when i tried i did conntect my ppc with ppc via bluetooth actvesync when i run HimaUpgradeUt.exe then a window open and shows mgs wait 30 minunt but after even 1 minunt got error also my phone got stop like dead and screen shows on top serial and on bottom it shows v1.3 i realy .sad. becouse now i cant reeboot also even ui have not data cable any body help me plz what i do now ?
thanks for my help
really want to say thanks who helpd me i upgraded now my spv m1000 my self without any problem becouse i brought data cable of i mate and its workin fine with my spv m1000 yahooooooooo xda roken
usman_hussain1987 said:
hi,
ive put my MDA into the cradle and get the Serial screen to change to a USB screen. ive downloaded the file and put it with the rom upgrade that i got frm T-Mobile. when i run the program on my computer i keep gettin "Connection Error" screen. what should i do.
pleas advise.
Click to expand...
Click to collapse
Hi Usman,
What OS of windows PC do you use? it can't work with windows vista. Try to downloads new version of active sync then try it again. The upgrade is specify, can't work in any kind of devices
I have this Siemens SX56 that I bought on ebay
say on information:
ROM version: 3.14.03 ENG
ROM date: 09/27/02
Radio version: 6.12
Protocol version: 324e4
I tried to look on this site but there are too many to read, please kindly someone can direct me to a direct link for the right version for me to download thank you
http://wiki.xda-developers.com/index.php?pagename=UnlockWiz
sx56 problem
I downloaded the XDA-developers-SER-v12 for my siemens sx56...
the problem is that when i downloaded it and have it activated... the phone show upgrading...will take 5 minutes to do so and do not unplug... the thing is...it has been over 5 minutes and it still shows in my screen and i couldn't get to take it off...
now the thing is as soon as it unzips it says that i have to have my phone on active sync... i cannot do so since the phone is stucked... now when i try to cancel it it says "cannot open the ROM image file" please download and try again" so that's how it goes repetitively... what is the best way that i can do with this? if it ain't going to work.. i would rather just use it as an organizer like it used to...
is there anything i can do with this?
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
and if you want to unlock use the exe tool rather then a very very very old rom
like
XDA-developers-SER-v12
The code will change depending on the model of the mobile phone. Every step has to be carefully followed while unlocking the phone.
SX56 problems
Hi, I recently got a brand new Siemens SX56 from ebay. It was never upgraded to firmware. I took the task of upgrading this but something happened that killed the process. Now the device is stuck at this mode even after doing a reset.
My steps were, I updated Active Sync to 3.7.1 (the latest version) The device is happily communicating with my pc.
Then started the upgrade and the screen says "upgrading will take 5 minutes, do not remove device or uplug power...during upgrade process..etc"
The program says it encountered an error during the upgrade and basically stopped the process. I knew this was bad. The instructions told me to uplug the device from the usb cable, do a normal reset, plug usb cable back in, and then retry the upgrade utility.
It won't because no active sync can't see my device because the screen is stuck on that "upgrading takes 5 minutes screen"
Is this device basically dead? Please help. This was a clear upgrade process and clearly the process got an error.
Hello gybanez,
I had the same problem and was able resolve the problem.
You have two options:
1. you can send it to me and I will do it for free.
or
2. buy these:
a. MMC card (at least 64 mb)
b. buy a Card Reader/writer that supports MMC
c. go to www.xda-developers.com and download "XDA-developers-SER-v12"
d. extract the ROM from XDA-Developers-ser-v12 (.nbf file).
e. also download XDA-TOOLS (used to copy the .nbf file extracted to
your new MMC card on the Card reader/writer.
f. now insert the MMC card into your sx56 press reset and power button
at the same time and it should take you to a screen which asks you
to press "action button" to download and once done do a cold reset.
This should do the trick and afterwards if you want to upgrade and or
customize it go to http://lumpistefan.dyndns.org/ great site.
PS: If anyone wants to correct/add to this please feel free.
Regards, JOHNNY.
--------------------------------------------------------------------------
This was the same problem I had... so finally i got it all and had it transferred in the MMC card...
the thing...as soon as I run it...it get stuck on "SIR TEST : Supporting Running"
and another is that I am using Vista and downloaded the latest mobile sync... but it responds that it doesn't identify the HTC mobile... really sad... can someone contact me via YM: [email protected]
need help