i installed a new rings rom. it worked fine, then my phone froze up, now it won load pass the opening page. it just says analyzing device component..... and its frozen there. please help, i run my company thru my phone and its very important...
what type of phone do you have? if its a G1 as i have then its easy to un-brick or un-lock...just plug your phone to your PC and format your sdcard again which will erase all of its data then ya good to go or you can remove the battery place it back then hold down your home plus power button at the same time till youir phone boots to the next screen then press alt+L then altW then reboot your phone and sign back in...
if this is a post about the g1 take it to the other forum because this is about the hermes
its a herm 100. htc 8525
have you tried to do a hard reset? If not give that a try.
I hope you installed Hard SPL V3 on it first... to check - hold power, OK button above the flywheel and reset with stylus, hold in until the tri-colour screen appears. Will show IPL - 1.04 and SPL - 2.10oli (if you've installed hard SPL V7).
If so, and you tried to Hard Reset 1st with no success, try the sd card method. If thats not working, on the pc, if using XP, go to activesync's connection settings and untick "Allow USB Connections". Connect your Hermes to the pc with usb after going to bootloader. Run the RUU_Wrapper.exe file again. This should re-install the rom.
You're gonna have a heap of trouble if you haven't Hard SPLed your Hermes.
Good Luck....
I dont have hard spl v3 on my phone. when i try to load another rom or anything i get error 270 the image file is corrupted. please check your update utility. what does that mean? and how can i work thru that?
Could anyone help me?
When I turn on the bootloader mode and connect it to pc,it won't make any connection and the red light won't turn on to..
Any suggestions?
I can't use my device because I can't flash new windows...
Could anyone help me?
First of all I’m running XP, and Active sync.
I used Soft SLP- VO.1 , I copied the NK.NBF
From a G4 safe rom into the soft slp folder.
While stuck in boot mode I did a hard reset,
Pluged in the usb and waited for power up.
Then I held the power button down and watched
Active sync try to connect at the same time started
Soft SLP . When active sync stopped I released the power button and then followed the instructions as normal. The phone went into white mode and copied all 100% but it still went into boot mode after it rebooted, but I was able to connect with the phone again. Now all we need is someone smarter then me that can figure out the rest of it. At least there is still hope for the dead ones.
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
Hello.
By pressing VolDown+PWR button, HD2 starts and shows the RED-BLUE-Green screen with a line with serial header.
Any idea why phone freezes in that point?
What do you expect to happen? You have pressed the keys to enter bootloader, and that is what the phone has done.
What do you want?
A hard reset .... then down Volume up and volume down and PWR button.
If you want to flash a new rom, you must join before the HD2 to the PC via WMDC
Wizzzzard2000 said:
What do you want?
A hard reset .... then down Volume up and volume down and PWR button.
If you want to flash a new rom, you must join before the HD2 to the PC via WMDC
Click to expand...
Click to collapse
No bootloader is what allows you to flash a new ROM. When the official ROM flashing instructions say establish a ActiveSync connection before flashing a update ROM. They are just saying that cause ActiveSync creates a connection with everythiong on your HD2 including bootloader even though you can not see it really, plus it is easier for most people to understand. But when you are in bootloader and connect your HD2 to your computer via USB. You will see the Serial in the white bar of bootloader change to USB. After it changes to USB you can go to the device manager in the control panel of your computer and your phone shows up as HTC USB sync, this is the sync that is required to flash a ROM via USB.
Why this phone causing so many issues?
I'm was search how to fix this, but nothing doesn't work.
I have no idea what to do, and now I creating a new thread, maybe somebody can help.
Let's start.
I HAVE SECURITY ERROR when phone power on. After message disappear, screen goes down..
- No bootloader unlocked
- No rooted
- No usb debuging enabled
- No custom rom
- No custom recovery
This is the first time connecting with PC (Windows 10) and
- No driver (this is the most important issus)
I tried some drivers and installed but because phone only show error and go to shut down I don't know is this drivers working...
- Can't run fastboot
- Can't go to safe mode/recovery mode
- Can't do hard reset with hotkeys
The first thing is driver, while PC doesn't see phone I can do nothing.
Another important thing is that I cant do to safe mode. Without safe mode I cant do fastboot and flashing.
So maybe someone can help?
The Security Error means you installed an unsigned image on a device with a locked bootloader. You have to flash the original firmware following either this or this guide. You can get out of the security error by just flashing a signed recovery with fastboot, too.
EdwinMoq said:
The Security Error means you installed an unsigned image on a device with a locked bootloader. You have to flash the original firmware following either this or this guide. You can get out of the security error by just flashing a signed recovery with fastboot, too.
Click to expand...
Click to collapse
I can't put phone in download mode. Doesn't work.
Nothing happening. Only show Security error on the screen.....
When connect with usb charger phone dones'n charge.
----------------------------------------
Put the phone in download mode:
Jellybean bootloader:
Turn off the phone, remove the battery. Put the battery in, hold volume up+down and plug in the USB cable, after 1 second of the USB cable being plugged in, let go of volume down, keep your finger on volume up until you see S/W Upgrade. If you see the LG logo you failed, repeat the step again.
ICS bootloader:
Hold Volume up + down while plugging in the USB cable is the method I think.
--------------------------------------
Volume up OR down, I always forget that.
After a failed attempt to invoke DL mode and switching phone off(hard reset usually), toggling the phone's power once increases the chance for success next time. Same as taking the battery out each time.
After the restore of the stock rom phone should reboot. If it shows the stock recovery's screen instead, phone will be instable later and might brick when trying to root it. Then repeat the flash process and it should boot now.
Just remove the battery, put it again, then hold Vol UP and while doing that plug in the USB. You're now in Download mode.