Lo all
My att >cingular sx56 suddenly stopped taking input from the screen
Did soft, hard restes and nada
Anyone have some ideas? Hardware failure perhaps
or is it a quick fix?
Is it a paperweight now?
lemme know
Related
Hello everybody,
Since yesterday my Xda doesn't work anymore. I tried to sync an image to my Xda, and then i got a strange stripe over my screen. I reset the device, and then the screen went blank and faded into blue stripes. When i put it in my docking it gives the noice of synchronizing. But i see nothing ... I already made a back-up and tried to reset it, soft and hard.
I doesn't work, who can help me?
Thanks!
Dennis
looks like a screen connector problem ... have you dropped it or something ?
No... what do then???
there are VERY few virus's out for pocketpc's
even non of them would ever be able to stray there
after a hardreset
i would say that it's a hardware issue
Maybe something with my bios? I can approach my Pocket pc through my computer. The screen goes from white until a white screen with stripes...
What to do?
Does anybody know if it's worse trying to repair a Wallaby that was stuck completely into water for several seconds? Although it seems that it still works, the display shows nothing than a backlight.
I upgraded to black 2 but at one point, my screen would not respond to my stylus. Since then I have downgraded to wm5 cingular 8525, I still have the same problem where screen does not respond. I am stuck at "tap the screen to set up". I have done a few hard resets but still nothing. any suggestions would be appreciated.
paulux said:
I upgraded to black 2 but at one point, my screen would not respond to my stylus. Since then I have downgraded to wm5 cingular 8525, I still have the same problem where screen does not respond. I am stuck at "tap the screen to set up". I have done a few hard resets but still nothing. any suggestions would be appreciated.
Click to expand...
Click to collapse
your touchscreen has broken... god knows how... nothing to do with the flash, must be something else you did... like hit it.
paulux said:
I upgraded to black 2 but at one point, my screen would not respond to my stylus. Since then I have downgraded to wm5 cingular 8525, I still have the same problem where screen does not respond. I am stuck at "tap the screen to set up". I have done a few hard resets but still nothing. any suggestions would be appreciated.
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Hermes_Problems
check your device serial...see if its a known issue....
hi guys,
quick question.
ive just replaced my dopod838pro housing and upon completion, WM6 wont auto-rotate. where have i gone wrong?? is it something to do with the little square of yellow plastic???
please help
thanks,
Drooch
also
the screen backlight sensor wont work either.
ive done a hard-reset, changed the yellow plastic to the original plastic from the OEM housing. all the connections are firmly connected and i am still suffering from
- no auto-rotate when sliding device
- keyboard backlight wont activate
please help as i dont want to send it 1500Km to get it fixed (outside of warrenty as well!)
Drooch
Did u solve your problem? I have the same problem with you
Solution
I recently ran into the same problem swapping to a new housing. As it turns out the housing I bought did not come with the magnet needed for the phone to recognize that the keyboard had been slid out. Just take the magnet from the old housing and attach it to the new housing. See the below link for pictures.
http://forum.xda-developers.com/showthread.php?t=332035&highlight=magnet
drooch said:
hi guys,
quick question.
ive just replaced my dopod838pro housing and upon completion, WM6 wont auto-rotate. where have i gone wrong?? is it something to do with the little square of yellow plastic???
please help
thanks,
Drooch
Click to expand...
Click to collapse
Hey everyone, i've managed to somehow crack my touchscreen, so i've wipped it open today and i've taken the screen out,
I am wondering will this touch screen work for me?
http://cgi.ebay.co.uk/LCD-Touch-Scr...s_RL?hash=item56334071e8&_trksid=p3286.c0.m14
The seller says that i have to have a black ribbon on my MDA Vario, however mine is orange.
Thanks very much.
Exe