I did the upgrade of the WM5 and at the end it strictly hangs and nothing happens there after. It does say, Congratulations....Please do a soft reset, but when I do that nothing happens.
So since it's supposively the new WM5, I hold all 5 buttons and it just goes back to the screen showing "serial" at the top and V1.02 at the bottom. But nothing else. It won't boot to the setup up screen or anything. I'm trying to upgrade the Audiovox PPC6600.
I've done everything I was suppose to but nothing. Any clues??
Related
am i the only one with this problem. sometimes (2 or 3 times a day) my qtek would just turn itself off when i push the power button (to kill the screen). if i press the power button it just does a cold reset (same effect as pressing the reset button)
am i the only guy with this problem
my radiio is 4.21. i tried several roms from the kitchen but the problem appears in all of them.
another problem that happens sometimes is that when i dissconnect the phone from the cradle it just turns it self off. pressing the on button makes it do a cold reset. is it supposed to do that??!! do i have a hardware problem
The same was happening to me till I upgraded my ROM to AT&T A.30.09 ROM, which is considered to be the best for me (since I've tried all the ROMs here in this site)
thanks i just upgraded to siemens a30.09 rom from the kitchen. lets hope its more stable.
it still goes OFF (sometimes) when i take it out of the cradel
i didn't say what my problem is properly in the very first message. the phone actually goes off by it self when the screen is off after some time
Ohh sorry to hear that! I just tried this ROM on my device & it worked!
Dude, seems you have a hardware problem! :?
my USB cord disconnected during a rom upgrade, and I can't get back to the recovery screen on the computer. My phone is currently in the 4 color mode (red, green, blue, white), how can I get it out of that to continue my rom upgrade or start over?
att 8525
Mine did that a couple times, I just started the process over again and my phone is working great
but doesn't the ruuupdater.exe have to verify that activesync is running so it can connect to the phone? the phone won't even load now, just goes to the multi colored screen.
I've also tried restarting the update program for both the 1.50 rom and the wm6 and both cannot connect to the device, because it is stuck at the multi-colored screen (which currently says "usb" since I have it connected to the usb)
Have you try a soft reset? That usually works for me.
how do i do a soft reset if I can't perform any functionality on the phone? not a smart remark, I just can't perform any actions on the phone, doesn't even boot up, like i said, only the red, green, blue and white screen appears when i turn the phone on.
thanks for your help guys.
itsbrianwithay said:
how do i do a soft reset if I can't perform any functionality on the phone? not a smart remark, I just can't perform any actions on the phone, doesn't even boot up, like i said, only the red, green, blue and white screen appears when i turn the phone on.
thanks for your help guys.
Click to expand...
Click to collapse
Get your stylus and poke the little hole next to the IR near the usb port. Check your manual if you can't locate it.
I understand where that is located though, when I click it, it brings me back to the multi-colored screen.
First of all do you have HardSPL installed? If yes there are no problems...just run the upgrade again and choose the SPL version you have (and not the SSPL, cause it hasnt`t worked for me!) and go ahead...it will work!...at work I have a bad USB cable and in last week have failed to upgrade about 3 times...every time can resume from the begining withouth problems...
Regards,
Primoz
Primoz, that was the info I was looking for, thank you so much. I received an error saying the image file was corrupt but I will continue working on it.
Now I'm having an issue when wm6 loads (still have not repaired the ROM update yet), it hangs at the Windows Mobile 6 screen and does not go to the today screen, any ideas?
Hi,
Juts soft rebooted my Tytn, and its not stuck on the initial boot screen (the four coloured bars).
Done a hard reset back to fatory defaults and still won boot past initial coloured screen. It says:
HERM300
IPL-1.04
SPL-1.40.Olipro
Serial
Any ideas?
Thanks,
Ants
have your tried taking the battery out and leaving it out for ten minutes then putting it back in and switching it on? IF you are still on the triolour bootscreen then you will just have to run a flash of a rom on it. That should get the phone back up and running
If you get it running though, do yourself a favour and install Hard SPL V7... You're running an older, less safe version. More chance for stuff ups...
Very odd
Hmm, well leaving the battery out for for a couple of minutes then rebooting makes it boot properley, but if I soft reset then it gets stuck at the coloured bars again unitl the battery is removed for a couple of minutes again.
I guess I will have to try flashing it later, but at least I have the phone running again so I can use it today, wil try flashing later.
thanks.
Ants
Didnt last long
got stuck at the coloured sceen again no matter how long I left the battery out now, just flashed the ROM again (schaps, same as I have been using for a year OK), and still same problem. I cant update the SPL as even on the odd occasion I got it to boot, installing spl2.10 requires a reboot at which point it got stuck again, and I couldnt get it to boot before the SPL loader program on the PC timed out with a comms error.
I am wondering if it is an intermittent hardware fault like a stuck button, would that cause it to get stuck on the first screen?
Ants
bugger!
just opened it up and a switch fell out, its the one from the comms button (just below the power button on the right hand side). Not sure my SMD soldering is that good to get it soldered back on again, must have hit it somehow or a previous drop and its just finally worked loose etc.
Although I find it har to believe that a switch would cause boot to fail, surley it just doesnt make a connection if its missing, just as if it wasnt depressed?
Ants
I have an old 8525 that I want to bring back to life... tired of the iPhone. It has Mobile 5 on it. Haven't used it in... oh, close to 2 years. Still powers up fine and all so I decided to try upgrading. I used Hard-SPL first and it errored out after the tricolor screen came up, saying it couldn't find the phone. So I popped the battery and went back in, and tried Auto Unlock v3a. Script failed, as did the manual method of copying up. Every time I get to the tricolor screen and it displayes HERM100 IPL-SSPL by Des and HERM100 SPL-1.09.ds. If I leave USB plugged in it says USB, otherwise it says serial. I do NOT have a SIM card in it right now. Am I missing something? It seems like I should have an option on the phone to do the upgrade, but I just have the colors I'd really like to get up to 6.5!
Thanks,
MP
My phone was working fine earlier, sent a text off, went to write another one, pressed the search button by accident and then the screen froze, wouldnt respond to any touch at all. Tried turning the screen on and off for a bit, volume was still working etc, in the end pulled the battery. Phone restarted, managed to get it to the normal lock screen (where it had my alarm/activities for the day displayed) but again, unresponsive to touch. Pulled again a few times and the same thing happened so I decided to leave it, figured maybe the heat/humidity here (on holiday in India) had wreaked havoc with some component.
Anyways, restarted again 30 minutes later and this time couldn't get past the windows phone screen -as soon as that loaded, it reset the phone and got stuck in a neverending loop. Held up and down together and got to the screen I think is called SPL (never bothered with any of the rooting stuff)
However, the TOUCH simply says "TOUCH NONE". So obviously theres a problem there. Everything else is the same.
I tried disabling/enabling the HTC log/modem bridge but that didn't help and did a reboot and factory reset a few times but that didn't help either. Now Ive got the device hooked up to my laptop, changed from serial to USB but I don't know what (if anything) I can do in this state?
I tried earlier holding down to put it into zune mode, it completed restoring the version but then as the zune software restarted the phone, it went back into the endless cycle - the zune software was still waiting for it to reconnect again to complete the process, but obviously I couldn't get it that far.
wrublo said:
My phone was working fine earlier, sent a text off, went to write another one, pressed the search button by accident and then the screen froze, wouldnt respond to any touch at all. Tried turning the screen on and off for a bit, volume was still working etc, in the end pulled the battery. Phone restarted, managed to get it to the normal lock screen (where it had my alarm/activities for the day displayed) but again, unresponsive to touch. Pulled again a few times and the same thing happened so I decided to leave it, figured maybe the heat/humidity here (on holiday in India) had wreaked havoc with some component.
Anyways, restarted again 30 minutes later and this time couldn't get past the windows phone screen -as soon as that loaded, it reset the phone and got stuck in a neverending loop. Held up and down together and got to the screen I think is called SPL (never bothered with any of the rooting stuff)
However, the TOUCH simply says "TOUCH NONE". So obviously theres a problem there. Everything else is the same.
I tried disabling/enabling the HTC log/modem bridge but that didn't help and did a reboot and factory reset a few times but that didn't help either. Now Ive got the device hooked up to my laptop, changed from serial to USB but I don't know what (if anything) I can do in this state?
I tried earlier holding down to put it into zune mode, it completed restoring the version but then as the zune software restarted the phone, it went back into the endless cycle - the zune software was still waiting for it to reconnect again to complete the process, but obviously I couldn't get it that far.
Click to expand...
Click to collapse
Hold down the volume up and volume down at the same time while hitting the power once you see the white screen you can let go of the power; in green lettering you're going to see the SPL, for most of us its 2.05.160023. This is the bootloader screen, everything there is done by the volume toggle, no touch screen here. Your phone is stock which means you won't be flashing like we customized folks do so let's start with the SPL, what is it and by some chance is it HSPL'd?
berrywr said:
Hold down ..... etc...
Click to expand...
Click to collapse
berrywr, TOUCH NONE on SPL screen means either corrupted touch driver or dead touch screen.