hi.
I was uploading my Herm to the rom 1.35.255.102 but my pc had a Fatal Error (blue screen like win98!!!!!!)
the updating process stops and the Herm is stucked in bootloader mode.
i tried to do what is on http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems, but without success.
pleas help me... i'm going mad!!!
i attach the usb monitor output
i can't attach...
why?
I tried also to flash the rom from SD, but i had an "not allow" error.
I tried again to upload the rom and I attach the USB monitor output.
PLEASE HELP ME!!!!!!!!
Is there anybody who could help me?
i did the command "info 2" and I had back this strange CID:
HTCSF kEØ(HTCEUSB>
Is it strange or is it right?
Corrupted CID and bootloader 1.09.
There's any chance you can fix it if you are able to boot into WM5.
Related
here is what I've done and what happened:
my ROM was HTC 1.18.255.3 07/22/06 with bootloader 1.04 then I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
after "SUCCESS!" message from "HERM_Unlock_v2a.exe", I connected my device via USB to PC and started to upgrade to Cingular 1.31.502.1 08/30/06 with aku 2.6 and bootloader 1.06 but when I get the "ID ERROR",without disconnecting the USB, I switched back to ugrading to previous ROM HTC 1.18.255.3 and the Processe started with no problem untill 98%, then suddenly upgading interrupted a message came saying connection error or somting like that!
since then my device is stuck on windows mobile screen and I've tested solutions in the "Hermes_Upgrade Problems" page and tried using the "Hermes SD Card flashing" method, But It seems impossible to flash my phone agian.
Help me PLEASE,HELP
someone help me please!
POF can't you help me please
I think Pof is away until 3rd december, I have the similiar problems with my second hermes, if you have then use mtty to see if you have an corrupted cid using info 2.
Do you have the original rom to go back on if so that will fix your problem.
I've used mtty to send some commands to my device and it answers to some of them but It just stop responding when I type "info 2" or "info 3".
and i tried this in mtty:
"
USB>checkimage
IPL CRC checksum = 0x9FCC6BEB
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xC0E1751A
ExtROM CRC checksum = Total Block= 1024
dwBlockIndex= 1024
Address Error1!!!
Get checksum ERROR!!!
0x0
Radio Image CRC checksum =
"
again It stop responding
also tried upgrading, no matter which ROM I try, it just can't connect to device.
and thanx for your relpy.
hi, since there is NO htc service center available around me I have to do something about it myself but my phone is still dead and I'm using a nokia 1101. PLEASE someone help me, pof are you back? can you help me?
I've tried all in this page:
"http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems"
and this one too:
"http://forum.xda-developers.com/showthread.php?t=280733"
and tested qtek 2020 rom but no use.
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
can anyone help me?
mht220 said:
I ran "HERM_Unlock_v2a.exe" on the device but I didn't use "HTC_Hermes_Radio_for_SIMunlock_v1.16.00.69" to save time and i wanted a CID unlock only.
Click to expand...
Click to collapse
Wrong, you also need a patched radio to CID unlock. Running only the exe file without the patched radio has no effect on the unit.
mht220 said:
from what I've found out my device hang up and stop responding when it gets the "INFO 2" or "INFO 3" or "TASK 32" or perhaps any thing involving CID so no upgrading utility is able to connect to it, the only thing is to connect to it using "mtty.exe" which I've tried any command found here, but no use again.
and my SPL is 1.04
Click to expand...
Click to collapse
Please attach usb monitor capture when trying to flash a ROM and a radio ROM. Otherwise can't help you.
here is exported files from usb-monitor:
and tanx for your reply
uuh... there must be something really wrong with it, no response to bootloader commands. If no sd card flashing is possible, I would suggest you to send it to service centre too.
pof said:
...I would suggest you to send it to service centre too.
Click to expand...
Click to collapse
It's a difficult option for me, as I should send it to a foreign country to service center,so are you sure there is no way like erasing somewhere using mtty?
pof said:
... no response to bootloader commands...
Click to expand...
Click to collapse
but it respond to some of them in mtty.exe e.g. "erase", "set" and some other.
pof said:
...If no sd card flashing is possible...
Click to expand...
Click to collapse
no it would stuck in "checking..." forever
tanx
HI,
I have same exactly problem on my spv m3100: since sept06 I've tried every kind of Unlock software,upgrade ROM and method found in xda..In mtty bootloader (spl 1.04) respond at every command but not "info 2","info 3" and "task 32".Sd card method works but if you try to upgrade other ROM,in your screen "loading..." and then "checking..." hangs on because the ROM upgrade must to match CID (I suppose..).I'll wait the next ROM Upgrade and ORANGE won't release it until gen07..
warrio said:
I'll wait the next ROM Upgrade and ORANGE won't release it until gen07.
Click to expand...
Click to collapse
it seems your problem is like mine if so, I don't think ANY normal upgrade can solve your prolem 'cause it can't connect to it.
so don't wait and send your device to service center, if you can.
I'm in your same conditions:there's no repair center here so I have to wait Orange who release a upgrade Rom (I hope asap..).
After flashing my XDA2 to WM5 3.5a, i've tried merging storage & extended rom to gain memory by following a thread on Airfagev. After doing a hard reset, i found out that my phone is not responding and all i can see are black horizontal lines on the screen w/out backlight. I tried soft resetting it but still it stays the same.
Though i can still put it on bootloader mode, it also wont finish reflashing and an error message appears that goes like this:
ERROR 100: Model ID Error
The ROM image you are trying to use is not designed to work with your Pocket PC.
Is there any way for me to fix this problem? I really need help from anybody who's knowledgeable enough in solving this problem coz' i am new in this field.
Pls. help.
Thanks in advance!
Yoo can use NOID utility for flashing
HimaUpgradeUt_noID.exe
bootloader
Thank you. I can now reflash my device to WM2003 but not to WM5.I think it's because of the bootloader which is v 1.06.Is there any way to change this to v 1.03?
Help pls.
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
I installed an "updated" HTC Home Screen Plugin (obviously not for my phone model #) and now my phone is frozen. It will boot up but the home screen is frozen (i.e., non-responsive to any button presses). I attempted to re-flash the ROM using various ones I found for the NEON but all fail for the same reason.
Specifically, connection to ActiveSync is not possible (I connect via USB cable but ActiveSync doesn't recognize device). So what I do is put the phone in bootloader mode and then connect the USB cable. When I do this, the ROM upgrade program recognizes the phone and gets to the point where it shows the screen "Updating the ROM image on your PDA Phone.." and the phone shows a status bar at 0%. However, after a minute the computer screen says "ERROR [262]: UPDATE ERROR" and the phone is stile stuck at 0%.
My question is if there is any other way I can re-flash my NEON300? I've heard that it may be possible to but the nbh file on a FAT32 formatted card. I tried this by naming the nbh file to "TOUCHIMG.NBH" and "NEONIMG.NBH" but neither are recognized by the bootloader.
Thanks in advance for any assistance.
Try changing usb port or even re-installing activesync.
Alot pf people had the same problem on different devices but the cause should be the same.
for example, http://forum.xda-developers.com/showthread.php?t=298516
Let me know how you go.
Thanks for the advice Seth. I followed the link (install/re-install of ActiveSync didn't help) and I think I found my problem. Do I need to CID unlock the phone to install the ROM's? I ran the type 32 command from mtty and it shows a value of FF for the security lock.
Thanks
wangobyte said:
Thanks for the advice Seth. I followed the link (install/re-install of ActiveSync didn't help) and I think I found my problem. Do I need to CID unlock the phone to install the ROM's? I ran the type 32 command from mtty and it shows a value of FF for the security lock.
Thanks
Click to expand...
Click to collapse
You should have read the WIKI before flashing your device... http://wiki.xda-developers.com/index.php?pagename=Flashing Guide and here http://forum.xda-developers.com/showthread.php?t=355730
Hey friens and developers,
I have read the information in post " dead hermes? corrupted radio? Post comments here" and follow the instruction "Device is stuck in bootloader mode".
My problem is, I can´t get a connection to my device (mtty), I have on 4 different PCs (XP or Vista Operation System) every time the same information --> "USB Port can´t not open".
My Question is, is the Bootloader damage ?
History:
The hermes are function well and I get yesterday a problem with frozen the Device. I solve the problem and do a hard reset, but after Installation the Device boot and stay now in the HTC Screen. (Look attachment). If i hardreset the device a see the tri-color Boot-Picture for a 0,5 sec, but no numbers.
THX for some idea´s
Thomas
Did you read the Wiki page for unbricking the Hermes?
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Yes I do, but I have the Problem with the USB Connection (mtty). You have any Idea for the USB Problem?
The Hermes now is function with USB. I install a new XP with SP2 on my PC and I have a connection.
Now I see the BOOTLOADER
HERM200
IPL-1.04
Herm200
SPL 2.-03
I want to flash the Device, but every Solution STOPT by 1%, "the image file is corrupted". Any Idea how to change the Bootloader to a compatibility Bootloader over mtty?
What ROM you trying to flash? It has to be a Hermes ROM or you're gonna end up with a permanent brick.
Have you installed Hard SPL V7? If you have you can use the sd card method to install the ROM.
If its a Hermes ROM and you keep getting the "the image file is corrupted" message, good, it means you won't have a brick at the end as the file is corrupted and could result in a brick. Either download the ROM image again or download something else. That error message is there to save your Hermes from brickage.
Cheers...