Hi @ll,
problem is i´ve to get an 1.60UK Rom to my MDAII with 1.72GER Rom. But that stupid Flash Tool from T-Mobile GER fails everytime. When i set my MDA to upgrade settings (Power-on + Reset + 4-way-Button) i get a screen saying "serial v1.06". Is that the Version of my bootloader ? Cause i found a thread that said "Downgrade with 1.06 isnt possible". Is that still so ?
Are there any ways to get my MDAII to Rom 1.60UK if i already have an 1.72 GER installed ?
Thx for help
Dr.Zorck
Hi
Im hopeing someone can help me I know this issue has probably been discussed loads of times and im a muppet for doing it, I was looking at different ROM's for my Orange M3100 and thought I would go for the IMATE JASJAM ROM so I could get MSN messenger .... I unfortunatly selected the TELSTRA 1.06 Bootloader ROM and downloaded instead of the 1.04 ( I should have read the posts on this ROM before!). Now I am stuck in bootloader 1.06 and as I have read the only way to get back to 1.04 is to flash with a ROM that is the same as my carrier (Orange UK).... the only Orange ROM is the Romanian one thats just been put on the WIKI, I have tried with this but its coming up Vendor ID error... if anyone can help or tell me how I can go back to 1.04 id be grateful? if not do I just have to wait until orange UK bring out a ROM with bootloader 1.06 ????
Thanks a lot ! James UK
Same problem with Cingular bootloader 1.06
I've the same problem with Cingular 1.34 bootloader 1.06, I try to downgrade with same bios CID (CWS__001 as I read on this forum) to bootloader 1.06 but I receive an error "WRONG VENDER ID" (also if i leave connected my PDA and I restart RUU utility it give me the same error)
I've also tried to install another vendor bios with bootloader 1.06 as suggested but I receive the same error message!!!
Emanuele
Unfortunately, you're stuck unless you either a) wait for a bootloader for your CID or b) pay the $38 to do the super-CID unlock. There's a thread on that stickied, so if you decide to do it, help them out by doing the usb capture.
Thanks... I have already unlocked the device with IMEI-Check.co.uk do you mean this? If I have unlocked it then do you think I should run IMEI check again on the device and it may unlock the CID ? cheers, James
If you run the imei tool again (with the latest version of theire software) it will reverse your bootloader to 1.04 and make your device super CID
I read all post (wiki instruction, also) about bricket hermes and kitl mode. Sorry, I can't put ansi log via usb monitor. But I put some situation from Mtty and Pb 5.0. Same situation is in Pb 6.0. Can somebody, please tell me what's happened with my Hermes? When I use original Ruu I get message "invalid vender Id" (probably radio area and cid corupted).
Orange spv m3100
herm100,
ipl 1.01,
spl 1.09.
kitl enabled.
no gsm,
stuck in splash (orange)...m05,s04,b06 d3.23.02 NO GSM.
When load PB 5.0 or 6.0 after ...Start....nothing happened. I also removed ril.dll...I think that PB cant recognize to download ext rom (to many bad blocks) and here stoped. Any idea how to disable in PB to load ext Rom? (maybe I am not in the right way about my opinion..???but I give a hope myself.)
Many Thank's in advance.
During th eflash of my rom radio with 1.54.00.10 the program stopped and my mobile restart in bootloader.
The problem is that the flash program doesn't want to restart flashing and my mobile stay on bootloader menu.
HELPPPPP Please..
What do you mean by "the flash program doesn't want to restart flashing"
Did you try to flash your original shipped ROM entirely to the device?
What is IPL/SPL on your device?
Sorry for my english...
I flashed with RUUWrapper.exe on my PC with usb connection but during the verification the soft said me error 260 the device not connect.
Is there a possibility to flash the rom radio without PC, directly on my mobile ?
Thanks
on the bootloader screen :
HERM200
IPL-1.04
HERM200
SPL-2.03
Looks like the FLASHING TOOL is not compatible to your device! What OPERATING SYSTEM are you using?
I am not sure if your device is already CID unlocked?
If you run on XP and your device is CID unlocked use the CustomRUU (search the forum), if not: read the WIKI!
My device is unlocked and I use wwindows XP
How can I flash with serial?
this is what you get for not flashing Hard-SPL. idiot
I'm ok but how can I do?
please...
HELLLP (ive been upgrading since the xda II) and i recently got a tmobile hermes with wm5! then got wm6 upgraded it and got to about 78% and my pc died and then i tryed recovery did not work had to go to work so i left it! got back and ive tryed so many more upgrades of the image with no luck its stuck on splash screen! ive placed it into bootloader mode then ran ruu wrapper and it gets to the bit of updrading (25mins and a progress bar) and the phone goes white with upgrading image 0% then on the pc i get error 262!! and thats as far as i got please can some1 help thankyou so much
here is all my information that ive got!
bootloader mode = herm300 IPL -1.01 (in white text)
Herm300 SPL - 1.04 (yellow text)
when i restart the phone and its stuck on bootloader mode this is the info
m 05 - r 1.05.05.00
s 04 g 32.36.7010.04h
b 06 d 3.62
please can u ask as many people as you can ive known about this since the xda II days but never needed help and i know some1 can help this is a great website and forum thanks
I unbrick my htc p3600 with HTC Trinity Stack Overflow exploit - how to unbrick any Trinity stuck in bootloader!! Can somebody create Hermes unbrick because when i use Hermes i always see message image corrupted because i not have activesync in my HERMES stack in logo only bootloader!!!!Cid locked!!! i can not intsall any rom hardspl...etc...try more then 50rom and all hardspl...all cid....now only see this http://forum.xda-developers.com/showthread.php?t=308691 for Trinity IS ANY CHANCE TO CREATE splxploit FOR Hermes with spl.nb THAT CAN RUN FROM DOS and change bootloader sspl ??? Sory for my bad english please need help where is pof???
please read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
this not work because i ask to someone create Exploit???
this not work i try all i not have kitl mode , and can not use SSPL+ActiveSync because i stack in bootloader-no active sync my problem is to change bootloader when device is cid locked only solution to create Hermes overflow exloit and when i have temporaly cid unlock my device then i can flash rom.
Flash a cooked ROM, leave the device in bootloader mode, connect with USB....run the RUU and select your bootloader version.
The RUU shouldnt care that the device is already in bootloader mode, just follow the usual steps.
Explain me more because
when i try to flash RUU SPL Downgrade Guide from http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
100% then always receive message image corrupted.
I WANT TO UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"
There are many people have this kind of brick but still no solution for it.
I want to ask the mods to make this thread sticky so if anyone find a sulotion for this type of brick would post it Here.
Summary :
IPL: 1.04
SPL: 2.03
CID: NO SUPER CID LEVEL=FFF
NO GSM
KITL Disabled
I have tested all the possible sulotions available in the wiki but none of the could help me unbrick my hermes.
P.S. : Please just post your sulotions here NOT your comments like "you CAN TRY THIS I TRY ALL IN XDA DEVELOPERS",
----so is any good man in this forum can fix this and create Hermes Stack Overflow splxploit HERMES to create
HERM100
IPL-SSPL by des
HERM100
SPL-1.09.ds - to temporaly fix and unlock cid first then we can flash any rom?? or any other metod.. ......can you explain please.???
How to jump spl address in hermes from dos??
Is any chance to jump spl to address in hermes or artemis from dos or mtty command what is spl address for hermes bootloader for artemis spl address is:.
* Kaiser Jump address is 0x00000000
* Artemis & Herald Jump address is 0x10000000
How to chenge bootloader in cid locked demaged
cid in hermes ???? HTC Trinity Stack Overflow exploit have this read in :
http://forum.xda-developers.com/showthread.php?t=308691
Who can explain and create for hermes?????
It's wierd!!!
there is no sign of POF and olipro!
I want to know where are they!!!
Maybe they are hired by HTC
Unbrick of Hermes IPL 1.04 SPL 2.03
mbsshop1302gsm said:
when i try to flash RUU SPL Downgrade Guide from http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
100% then always receive message image corrupted.
I WANT TO UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"
There are many people have this kind of brick but still no solution for it.
I want to ask the mods to make this thread sticky so if anyone find a sulotion for this type of brick would post it Here.
Summary :
IPL: 1.04
SPL: 2.03
CID: NO SUPER CID LEVEL=FFF
NO GSM
KITL Disabled
I have tested all the possible sulotions available in the wiki but none of the could help me unbrick my hermes.
P.S. : Please just post your sulotions here NOT your comments like "you CAN TRY THIS I TRY ALL IN XDA DEVELOPERS",
----so is any good man in this forum can fix this and create Hermes Stack Overflow splxploit HERMES to create
HERM100
IPL-SSPL by des
HERM100
SPL-1.09.ds - to temporaly fix and unlock cid first then we can flash any rom?? or any other metod.. ......can you explain please.???
Click to expand...
Click to collapse
Hi
I had the same problem, I tried I think all the tips I read on the forum, finally I put my phone in Bootloader mode, I uncheck usb connectios on active sync, and the most important thing I tried with the following ROM: RUU_hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship for my surprise after trying will all kind of roms, this one did the installation of a new radio and finished with 100% in downloading the new OS and radio GSM, I have a working Hermes! If I could help in anything let me know
edyfast said:
Hi
I had the same problem, I tried I think all the tips I read on the forum, finally I put my phone in Bootloader mode, I uncheck usb connectios on active sync, and the most important thing I tried with the following ROM: RUU_hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship for my surprise after trying will all kind of roms, this one did the installation of a new radio and finished with 100% in downloading the new OS and radio GSM, I have a working Hermes! If I could help in anything let me know
Click to expand...
Click to collapse
Did you have exactly the same problem with
IPL 1.04
SPL 2.03
NO GSM
NO CID
KITL Disabled?????
and if it's true,is that ROm a WM5 or WM6 ROM??
Tested! But DID NOT HELP!!!!!!!!!
8525 bricked IPL 1.04 spl 2.03 Solution
koorosh_bsboys said:
Did you have exactly the same problem with
IPL 1.04
SPL 2.03
NO GSM
NO CID
KITL Disabled?????
and if it's true,is that ROm a WM5 or WM6 ROM??
Click to expand...
Click to collapse
Hi
It is a WM5 Rom, this is the only one I tried that worked at the first try!, however it seems at the beggining that wont work because it takes too much time to advance in the percentage bar on downloading, for me took about 35 minutes, the good notice is that this rom completes the installation and installs a WM5 but it is a good start since once you are done with this you can install hard spL on your phone, you mentioned that didn´t work please be patient if you notice that the percentage bar is working, at the end this will fix your phone.
where
can you sent me link to download or put in megaupload to try this rom please respond its very urgent to try.Sent me link to download??
And if my phone cid locked this will work or not???/
Unbrick 8525 IPL 1.04 SPL 2.03
Hi
here is the link:
http://rapidshare.com/files/25381512/RUU_Hermes_CINGULAR_WWE_2_1_.15.502.3_6275_1.40.30.00_108_Ship.exe
My phone was cid locked and KITL disable before I fixed it! now I did the unlocking using PoFs cid and sim unlocker and it worked fast and easy at the first try!
I understand your urgent requierement I was 15 days with my phone damaged with the only showing of IPL 1.04 and SPL 2.03 "serial" text on the bottom.
This Link Not No File Found
CAN YOU UPLOAD NEW LINK this link is dead :http://rapidshare.com/files/25381512/RUU_Hermes_CINGULAR_WWE_2_1_.15.502.3_6275_1.40.30 .00_108_Ship.exe
please use megaupload.....respond me please when you add new link.
THIS LINK is dead NO FILE FOUND
This will not work only solution to unbrick any Hermes stack in bootloader cid locked that somebody create Herems Stack Overflow exploit - ANY CHANCE TO CREATE splxploit FOR Hermes with spl.nb THAT CAN RUN FROM DOS and change bootloader sspl temporaly tehn we can flash any rom ???
Here is link for Trinity and work i unbrick my p3600 with this cid locked stack in bootloader:
http://forum.xda-developers.com/showthread.php?t=308691 for Trinity IS ANY CHANCE TO CREATE splxploit FOR Hermes
Sory for my bad english please need help where is Pof to creat this for Hermes??Imei check and htc men help??
How to unbrick herm100 in tri-clour mode
download Mtty1_42.
CONNECT brick herm100 with usb
FROM the port setting,choose USB
A white page should open
TYPE set 14 0
TYPE set 16 0
soft reset with stylus.
HURRAY u are down.
dont 4get to say thanks