Hi @ll,
problem is i´ve to get an 1.60UK Rom to my MDAII with 1.72GER Rom. But that stupid Flash Tool from T-Mobile GER fails everytime. When i set my MDA to upgrade settings (Power-on + Reset + 4-way-Button) i get a screen saying "serial v1.06". Is that the Version of my bootloader ? Cause i found a thread that said "Downgrade with 1.06 isnt possible". Is that still so ?
Are there any ways to get my MDAII to Rom 1.60UK if i already have an 1.72 GER installed ?
Thx for help
Dr.Zorck
Related
Hi
Im hopeing someone can help me I know this issue has probably been discussed loads of times and im a muppet for doing it, I was looking at different ROM's for my Orange M3100 and thought I would go for the IMATE JASJAM ROM so I could get MSN messenger .... I unfortunatly selected the TELSTRA 1.06 Bootloader ROM and downloaded instead of the 1.04 ( I should have read the posts on this ROM before!). Now I am stuck in bootloader 1.06 and as I have read the only way to get back to 1.04 is to flash with a ROM that is the same as my carrier (Orange UK).... the only Orange ROM is the Romanian one thats just been put on the WIKI, I have tried with this but its coming up Vendor ID error... if anyone can help or tell me how I can go back to 1.04 id be grateful? if not do I just have to wait until orange UK bring out a ROM with bootloader 1.06 ????
Thanks a lot ! James UK
Same problem with Cingular bootloader 1.06
I've the same problem with Cingular 1.34 bootloader 1.06, I try to downgrade with same bios CID (CWS__001 as I read on this forum) to bootloader 1.06 but I receive an error "WRONG VENDER ID" (also if i leave connected my PDA and I restart RUU utility it give me the same error)
I've also tried to install another vendor bios with bootloader 1.06 as suggested but I receive the same error message!!!
Emanuele
Unfortunately, you're stuck unless you either a) wait for a bootloader for your CID or b) pay the $38 to do the super-CID unlock. There's a thread on that stickied, so if you decide to do it, help them out by doing the usb capture.
Thanks... I have already unlocked the device with IMEI-Check.co.uk do you mean this? If I have unlocked it then do you think I should run IMEI check again on the device and it may unlock the CID ? cheers, James
If you run the imei tool again (with the latest version of theire software) it will reverse your bootloader to 1.04 and make your device super CID
Hi
I tried to unlock my orange m3100 (swiss) SPL 1.04. When I run the MaUpgrade I get the ERROR message 120 Country ID mismatch and the program quite / radio rom version remains at 1.06.00.00.
Please help me - thanks
Surely your running the MaUpgrade_noID.exe program??
S.K.
Which bootloader do you have?
[edit]Sorry-I just saw you listed 1.04 in your original post[/edit]
Run the software when your fone is under the tri-color screen mode, rather than wm 5.0
I tried to upgrade my athena (french rom) with wm6 english version, and it was the crash
the original rom is dammaged and athena w'ont start enven with hard rest ???
(I did unlock it, it was bought in belgium and its was sim-unlocked).
Any help please to re-install original french rom or any thing else ???
Enter Bootloader mode and check if it says SPL: Olipro
If yes, that you should be able to flash a ROM (the one for your device)
even without ActiveSync Connection
If not, you haven't unlocked correctly.
Don't know what you can do then -_-
I have flashed my SDA Music to WM6, but i will now again WM2003 SE with German Language..... i need help, i found no ROM...
Greez Richy
I don't know if it is old news, but reverting to 2003se is possible and very simple.
You just have to get into bootloader mode (tricolor screen, whatever it's called) format filesystem with mtty (format BINFS), reboot, get in bootloader mode again, and apply T-Mobile upgrade.
does any1 has Orange Spv C550 ROM.. i need to downgrade from WM6 but dont hav da C550 ROM & can't find it online as yet can any1 help plzzz.....
Hello everyone.
I've problem while unlocking my Herm(MDA Vario II form Era). I downloaded Unlock_v3a prom forum. SPL updated succesfully to 1.40 Olipro byt while installing Radio it stuck on 0%. Then i have only bootloader screen and I install WM 6 wersion of operator (but without Radio etc because when i tried install full it stuck on 12% - radio install). Anyone have some idea what's wrong?
Maybe it is SPL case?
Thanks for replies!
Ok i want to refresh my Thread. I was reading many articles about Hermes and my case now is like that.
My Radio is working i can talking by PDA but only with cards of it's operator, when i'm trying install Radio installation stops on 0% i try to install 1.14, 1.18 Radio but always with the same result.
My IPL is 1.01
SPL is 1.40 Olipro
Radio ver. 1.05.02.00
Running on WM 6