i have a Qtek 1010 like new ,, and it works well , but when i put it on the cradle for charging it turn off , and then when i take it off the charger it turns on again ...so if anyone please has a solution , tell me ...
You mean it goes really off, so that it restart complete after releasing it from the cradle, or does just the display goes off?
Stefan
thanks for reply ,,, what i mean is that it s completely turn off ,,not only display ......
and when i get it off the cradle it start again from the begining and asking for aligning screen and so on...
Related
:?: i finally wanted to use my siemens sx56 after a year... Now it doesn't want to start all the way up... Lots of problems.. Battery light will not come on... No start bar on screen... Resets itself all the time... blinking backlight about every 15 seconds... etc... Please help me... I just want to use it again... it has wallaby bootloader 5.15... ppc 2002 3.14..
Have you tried a hard reset, that is using the unscrewed top half of the stlylus in the hole on bottom right of xda, leave for one minute then press again.
I recently picked up an SX-56 that was long unused. It took a few minutes on the power before the lights would come on. Plug it in and let it juice for a minute, and then a cold boot is definately in order. Also, make sure that the SIM door is fully closed.
thanks for reply guys... But i tried all of that stuff... sometimes it will bring up windows but there is no start button... also i can't even use a stylus because it's not tuned up.... also it won't let me connect to activesync... comp see's it but cannot connect...
i think u need a new one
Can you get to the bootloader?
Help i tryed to install the new rom q.tek 1.72 on my xda2
Had some problems after a lot of rebooting suddenly the xda2 wont do a thing. I mean even the battery light doesnt work when i put it on ac.
No hardreset possible. also tryed hardreset + pressing the directions pad . Not working. Can somebody help plz
I had this also one time after a failed upgrade. For me it was solved after removing the battery for a few minutes.
Can also try leaving the unit in the cradle on charge for an hour or so then trip a reset.
Ed
thanhx i removed the battery and charged it in the cradle and it worked
my xda ii became dead..i dont knw how..i had kept it in d drawer wen i pressed the power button ..the phone didnt turn on..i tried doing the soft reset then too no difference..then i removed the battery n kept iit for 1 hr..then too the phone didnt get on..then i tried puttin it on the bboootloader mode ..the phone didnt goto the bootloader mode..i guess it is completely dead ..please tell me Soon what do i do?any ideas?
please please m really tensed
have you try to charge it
put power on it maybe your ineternal batery is empty
put it with a power charge then press power buton leave 5 to 10 minutes later go check if the orange light is lit
try that
same thing happened to my old ipaq h5550. i left it for 4 days without battery and it just wouldn't turn on anymore. but try this cause this somehow work for me. remove your battery then plug it in while pressing the reset button almost the same time you plug in your battery. if that doesn't work just leave ur unit plug in to the charger for a time then repeat the same procedure.
goodluck.
Is your i-mate still dead??
ok i just got this SX56 from a friend. when its on the cradle it says its charging and it will boot up. i see the charging lamp go green, i take it off of the cradle. BOOM dies and it wont turn back on via the power button, soft rest, or hard reset. and i put it back on the cradle and it asks me for the align screen again, like every time i take it off of the cradle and put it back on. it will do some sort of reset and will go back to the align screen. im thinking the battery is shot??? any other ideas please?
could be the battery hasnt been charged properly... try to charge the battery for atleast an hour before you turn on the device.. if it doesnt charge maybe there is something wrong with the battery. cheers
Hi everyone, i have a little problem with my cingular 8125. I am the second owner, so i might not be able to give every details. However, the problem is this: the first owner had wm5 english and decided to put on wm6 italian, so he tried but the wizard brickked. Now, the phone won't turn on, won't go in the bootlader (camera+ power) and won't charge if plugged in the USB. The battery was dead, i charged her but still nothing happens... the wizard act like dead. what can i do? Jtag?
Plz Help!
Thx
If you mean you don't get the charge light then plug it in using the original WALL charger. The charge light should come on after a minute or so. DO NOT press the power button for at least 20 minutes. If this doesn't work then you need a new battery.