Related
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.
Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Have you read this http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners ?
Re:
Yes, I have, plus all the links branched from there. After about 3 hours of reading, I felt ready to try flashing, but it didn't work. The HardSPL utility is done downloading, so when I get home I'll try that and hope I finally get a successful upgrade. If not, I'll be back to the forums. Thanx!
What ROM are you upgrading to? The official AT&T ROM? I'd try that first if you're not already.
BDsBabyGirl said:
Even after reading this forum all nite, I am still soooo confused, maybe too much new info in m'head. At any rate, I am trying to UG from WM5 to WM6 and am having a heck of a rough time. Everything goes good until it actually starts the process, at which time I get the 260 Connection Error. After plenty of research on here, I decided to try to "flash" the ROM, to no avail, for nothing happened. I can get into bootloader mode but then nothing else happens (perhaps I'm not waiting long enough? How long should I wait?) and I never see the screen pictured here - http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing - so I just give up and reset. I am currently downloading the HardSPL utility so I can try flashing after the IPL and SPL ugrades. But I do have some questions still --
(1) Does my phone need to be "unlocked" to do this and how can I tell if it is or isn't?
(2) Can I just use the ROM that I downloaded from the HTC site or must I use one found somewhere on this forum?
Any other advice? All will be appreciated. Thanx.
Oh, yeah -- I'm working with a Cingular 8525 Hermes [HERM100 model number] Pocket PC. It's specs are:
ROM version 2.15.502.3
ROM date 04/09/07
Radio version 1.40.30.00
IPL 1.03
SPL 1.11
Click to expand...
Click to collapse
What operating system are you using? If its Vista you MUST use Mr. Vanx's guide to get past the connection problem. The standard Vista HTC driver is wrong when we want to flash rom's in bootloader mode and vista WMDC. Get it here:
MR VANX's VISTA GUIDE
Hard SPL is great after that. Just remember you warranty may be void if you have to go to AT&T for repairs and the see that bootloader. You shouldn't need Hard SPL to flash the standard AT&T rom or VP3G's or other AT&T based ROM's, but better safe than sorry.
Be sure to close EVERYTHING in the taskbar! Don't start any programs, allow any updates to mess around with the computer while its flashing..In fact, I disable my AV program and internet connection totally when I flash ROMS. (My Kaspersky started updating and virus scanning during my 1st flash..sucker froze and freaked me out!)
Once I dealt with unlocking and connection issues, I flashed the standard AT&T ROM, performed a hard reset immediately and then connected via WMDC and synced everything. I tested it for a few hours then decided to flash VP3G's excellent AT&T based ROM v3.62.3..I like to do a hard reset immediately after flashing to burn everything in...I've seen others in this forum do the same.
Another ROM I've found fun is S64's(Starbase64) 3.62 WWE v9 - It's not AT&T based but you can get WPBEAR's Config files to set your Medianet and proxy. There are other At&T settings CABs out there like Dr. Puttinghams. S64 ROM also includes Advanced Config 1.1 to set your keyboard to Cingular mapping.
Good Luck!
re:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Ahhh...Sorry for your troubles...I didn't have luck catching an upgrade from the SD Card method on my 8525 either.
I know it seems a bit much but, is your active sync working correctly? Upgraded to 4.5 and all that? Can you sync and Backup all your data then try uninstal, reboot, re-installing AS?
I wonder what would happen if one tried Mr Vanx's instructions on a Win XP box?
I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
BDsBabyGirl said:
My desktop PC is running Windows XP...
After trying the HardSPL method - which upgraded perfectly - I continue to have the above-mentioned problems; 260 Connection Error and inability to move beyond the tri-color screen to the one pictured on the page which instructs how to flash via SD card.
Thanx for the list of ROMs I can try. For the record, I have been using the "official" one I downloaded from the HTC website. *sigh* I guess I'll next look for the tutorial I saw somewhere around here on how to upgrade from the tricolor screen [or something like that, I think it was], as well as your advice.
But I do have another question -- how do I format the SD card? The tutorial I used on flashing with it mentioned formatting so I'll retry it with the card newly formatted (I didn't because it said I could just delete everything off the card OR format it).
I'll let you know how it goes...
Click to expand...
Click to collapse
Just another tip... Try a different usb port. I've found that sometimes certain usb ports behave differently during the upgrade procedures. So, far I've upgraded three 8525's on Win XP and only one gave me the problem you've described and connecting the sync cable in another port corrected the problem.
Re: my Post
shihayadreamer said:
...I also had heard somewhere about messing around with when Active sync is started. Also as a last ditch, maybe try this from the HTC Wiki:
http://www.htcwiki.com/thread/667087/ActiveSync+and+Rom+8525?t=anon
Good luck
Click to expand...
Click to collapse
OMG! SHIHAYADREAMER! That was JUST the TICKET! I read it and realized that I'd been doing it right all along, I just didn't realize I was! THIS time, I hooked up my cable at the very beginning and let it go. Before, I'd started waiting to hook it up until the instructions asked if I had because I'd gotten to the tricolored screen (the bootloader?) the 1st time and figured I did something wrong. Thanx to that forum, I returned to what I did the very first time and got victory! *falls down sobbing and weeping with joy* I wasted 25 hours because of fear! OMG! *dances around, singing* I've got WM6! I've got WM6!
I know that being reminded to turn off my firewall and stop all the programs in the taskbar played a big role, as well. But I just give a big "Thanx" (on Thanksgiving! *LOL*) to everyone who answered this board because you all helped me so very very much.
Hi All
Been dying to upgrade my Advantage 7501 and try out some of the new ROMS and the new radio on here. Went to the sticky and spent a day browsing the forums to see what I could pick up, even went to how not to brick your device thread. However I am still having issues
First thing I did was remove the SIM and SD cards, I had just reset the device yesterday so I did not reset again. I got a hold of the AthenaWrapper program and it worked as advertised. Getting into bootloader I have:
Athe100
IPL-v2.02
Athe100
SPL-v1.20.Olipro
However, this is where I run into issues. A soft reset does nothing but give me a black screen. I can get into the hard reset screen okay but when I cancel out I get back to the black screen.
Device also does not sync up with Activesync or WMDC?
Not sure what to try next or how to get back on track
Have tried on both Vista and XP.
Anyone have any suggestions
JP
Try to flash a ROM now, starting in bootloader mode. Hold the volume slider to down and then press into the reset hole.
Chooose one (SPL 1.2) from the sticky topic in the athena WM6 section
Progress
Thanks for the reply
Went back and remembered I had to flash the radio first. So I got the 1.57 update and that went as planned. One bullet dodged. Then I went ahead and grabbed some of the ROMs from the located you mentioned and that went thru as well. So it looks like I am back in business. Appreciate it.
PS I see references to SPL 1.2 and 3.5. I also read somewhere that the AP4 upgrader containts 3.5 (http://forum.xda-developers.com/showthread.php?p=2825883). Is this just a new version of the same thing?
JP
FollowUp
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
Check the SPL version before flashing a new rom!
MIchyPrisma 6.1 Crash / Lost Unit ID / NO MTTY Upload
hello,
just read this thread after the same happens to me... ;(
jhenel wrote :
´Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. ...´
The same hits me.. break after 93%
No kind of rom can be installed, error from the romupdate utility from ´wrong unit id´ to ´can´t use this update tool , you need a newer one´ everything, but no rom will install. all hangs after 1% , stock-roms also.
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
http://forum.xda-developers.com/showthread.php?t=429013
you should read this first
http://forum.xda-developers.com/showthread.php?t=429013
Make an effort to search for an answer before asking a question
jhenel said:
Just an FYI. I got things to work but not after a few more moments.... I initially tried to update to MichyPrimas 6.1 ROM and it got to 93% complete before bombing with a comm error. That was bad! Went thru the recovery wizard but it basically toasted my model id. Nothing would work. Found a copy of mtty and that did the trick. Just so other know, you need a mac address to run in the mac1.exe program. Some people report having this on the inside of their battery cover. No luck here. I did find it at the router from a connection before I started flashing. A spot of luck there. All went well and I got my model ID back and was able to resume normallly. I flashed the Black Touch PK3 ROM with WM6 for now till I have a bit more time to go to 6.1.
Anyone else have issues with MichyPrima's 6.1 ROM like I did. Looks cool and I want to try it but not if it bombs out on me and I have to mtty my way back all the time.
Cheers
Click to expand...
Click to collapse
please people, READ!!!! someone above your post just told you to flash 1.2 rom, in BIG RED LETTERS.
the AP4 is what upgrades you to SPL 3.5, then you won't have a problem with 3.5 roms
(btw good thing this reminds me to release a separate 3.5 SPL upgrader)
doktor.wahnsinn said:
hello,
i tried mtty, everything fine until task 32,level =0
then i want to upload the produced file (mac file generated through mac1.exe,spl1.x)
it starts uploading and ends with ´Fail to synchronize with the host (1)´
any ideas `?
ipl-v2.02
spl-v1.20.olipro
nothing works, only bootloader.
i can connect with mtty, but not upload files.
no rom update works..
help....
greetings,
doktor wahnsinn
Click to expand...
Click to collapse
please read my really detailed instructions a bit more carefully. I could bet you skipped the part about trying to copy all the files and mtty to C:\ or the step saying click OK for the small popup in mtty. or the warning that you need to type full filename includign the .bin file extension.
also i hope you use the version of mtty i posted
if that's not it, you can also try a different PC
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Your phone's cdma. This is a gsm forum. I'm assuming that you're trying to brick your phone with the gsm hard spl and not trying to flash the proper hard spl. Stop doing that, your phone is getting pissed at you. Go to ppcgeeks or the cdma (Herman, not Raphael) forum here.
haha leave it to me to find the wrong way to do something. I appreciate your heads up Ted!
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Try here: CDMA Herman
same issue on GSM phone
Hi I have the same problem on a GSM phone.
I get the updating bar on my phone- it stays stuck at 0%.
then a communications error
Thanks in Advance
What is the problem with the RUU update?
I have searched for a solution to the RUU update/upgrade problem; none so far. Apparently, it is a major issue. I am interested in upgrading my Windows CE on my Xperia 6.1 to 6.5. I must have tried over a dozen times. The update process stops at 0% and Error [262] is reported. What can we do to resolve this? Is it compatibility or scalability issue? is it a problem with the software? The fact that it is working for some . . . and not for others is a source of concern about the stability of the software and this has potential implications; or it may well have to do with the hardware limitations of the PDA. Any ideas of a workaround?
You might try the Experia forum. You also might want to try Experia Roms.
I used to experience this issue as well. I simply go into communications and hit the USB to PC connection. Then remove the advanced functionality check. This has resolved many of the communication errors when playing with ROMS. This has been true with both GSM and CDMA devices.
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Dunno if i can link to another forum. If not, appolgize and Admins remove the link than please.
For the 262 error, look here:
http://www.4winmobile.com/forums/windows-mobile-faq/13329-ruu-errors.html
player911 said:
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Click to expand...
Click to collapse
Yes they are coming with a new bootloader. I just got my phone replaced from ATT and the new one came with 1.95 version while originals were 1.90. There is no HARD-SPL out for 1.95.
The way to do it now is to flash an old original AT&T rom with the 1.90 bootloader (since it's original, it won't require HardSPL). Then go ahead and everything should work as described in this forum/wiki.
Interseting. Sounds like a winner. Next time he comes around I'll try this.
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
smicale said:
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
Click to expand...
Click to collapse
You should probably go to your ATT store and tell them you'd like to get the official Hard SPL update.
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
smicale said:
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
Click to expand...
Click to collapse
If u want to use not the official rom made for ur provider and phone, hardspl is the only way. Any custom rom needs hardspl. Otherwise ur phone will not accept the rom.
But look here http://forum.xda-developers.com/showthread.php?t=410150
and flash the stock 1.90 SPL first, then u are ready for hardspl.
Description how to do stock spl is in this thread. Its normally meant for going back to stock for repair, but it should also solve ur issue.
NOT SHURE BECAUSE IN THE CDMA SECTION, IS UR PHONE CDMA OR GSM. MY SOLUTIUON IS FOR GSM !!!!!!
U SHOULD CHANGE THE POSTING SECTION IF ITS GSM !!!!!
Try doing the HardSPL in a Windows XP machine (needs .NET Framework 2.0 and ActiveSync). Goodluck.
i had the same problem as you and i maybe have a solution for you
go to your usb settings and look if you have a check box saying something about advanced networking. if it is indeed checked uncheck it and your problem will be gone hopefully
i did it on my telus touch pro and i am now able to upgrade my phone to winmo 6.5