Hi there,
I upgraded to WM5 but wanted to downgrade to WM2003. But halfways the downgrade the PDA hung. The only thing I can see in the screen is Serial at the top and v1.06 at the bottom. When I put the PDA in the cradle, Serial changes into USB. When I try to install firmware from a ROM, after a while I get an Error 101: Connection Error. I think that in some way the connection cannot be esthablished between cradle (PDA) and the computer.
Trying a soft or a hard reset doesn''t seem to do anything.
Can anyone help?
MDA II
i have the same problem. it keeps on giving me a connection error. please can some one help.
the same problem with SPV M1000. anyone have the solution?
do a hard reset guyz by this method
HOLD DOWN UR POWER BUTTON+RESET (pin at bottom)..u will see 1.06 or what ever ur bootloader version is at bottom and at top u will see SERIAL..when u connect it to USB it will change to USB....and VOILA !!!
Happy Flashing
Same Problem
Did as you said and my computer doen't pick up the connection through the cradle. HELPPPPPPPP!!!!!!
prob
HERE already tried to hardreset and then trying flashing
but can't sucess
The same problem..
we are on the same trouble...
until now, there's no way to resolve this problem,
the lucky if we can connect to PC,
i think its the connector problem,
maybe using a new sync cable rather then the cradle then
the cradle was always hit or miss for me
but i still had my wallaby cradle which always worked
Rudegar said:
maybe using a new sync cable rather then the cradle then
the cradle was always hit or miss for me
but i still had my wallaby cradle which always worked
Click to expand...
Click to collapse
I have tried about 3 different cables and the cradle one.
and so tried to 3 different PC's to connect and got same error
btw, thanks...
From what I've seen so far problems can be caused by:
1. A firewall needs configuring or temporary disabling.
2. The usb connection shouldn't be through a hub but straight to the usb on the motherboard.
3. Dubious connection to the cradle.
rhilton said:
From what I've seen so far problems can be caused by:
1. A firewall needs configuring or temporary disabling.
Click to expand...
Click to collapse
my firewall is active exception activesync service
some time disable
2. The usb connection shouldn't be through a hub but straight to the usb on the motherboard.
Click to expand...
Click to collapse
i have modding motorola like e398, e1, e2, L7, v3i etc before
i never use USB-hub, i have 8 port USB straight to motherboard,
3. Dubious connection to the cradle.
Click to expand...
Click to collapse
i dont understand about this (dubious ?)
when dopod 838 friend connected to my PC it was OK, no problem,
thanks rhilton
no pc usb connect
Have checked your phone connector? it happened to me once:1 pin was out and no way to sync !!!
CENTER]ion[/CENTER]
imamlab said:
my firewall is active exception activesync service
some time disable
i have modding motorola like e398, e1, e2, L7, v3i etc before
i never use USB-hub, i have 8 port USB straight to motherboard,
i dont understand about this (dubious ?)
when dopod 838 friend connected to my PC it was OK, no problem,
thanks rhilton
Click to expand...
Click to collapse
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
Related
xda 2 gone to serial/usb bootloader and is stuck .
im a nub and need help to revive this xda2
any help or pointers would be apperciated
Take a look at my post here. It may help you.
dcs ive been round and round in circles mostly ending up at your thread
cheers for that and great work
i learnt quite a bit and used your post to check the rom files i had and set them to o2 insted of cdl .
problem turned out to be me USB and as soon as i used me lappy all went well .
so for future referance 112 error is usb communication problem
Tnx to everyone here , without you i would have given up on me lovely xda 2
keep up the good work
Glad you got sorted
Out of interest, what was the problem with your USB?
Hi got the same error, and I don't have any laptop. Now I am stuck!!
Any suggestions?
Thanks,
Claudio.
claudioita said:
Hi got the same error, and I don't have any laptop. Now I am stuck!!
Any suggestions?
Thanks,
Claudio.
Click to expand...
Click to collapse
First things to check are that you have your device connected via the USB cradle plugged directly into a USB port on your PC. Do not use a USB hub. Also make sure that the power supply is plugged into the cradle.
Still no luck, now I am trying to revitalize an old notebook: reinstallink windows 98, outlook 98 activesync and so on (burning all the software on a CD...what a pain).
and
yes now it seems working......Stage 2 at the moment.
Very strange , never had any problem with USB on my desktop so far...
I seem to have a problem with my XDA II (Dopod 696). The device won't sync via USB, but it will sync via infrared. When i plug the USB cradle/cable in, the computer complains that "USB Device not Recognized" saying that one of the USB devices attached to this computer has malfunctioned, etc..
Now the problem is, this phone comes in Chinese software. If i have to active sync via BT normally it would be fine, but i need USB support to reflash in WWE ROM to the phone.
Or has someone come out with a total solution for flashing the phone via SD card already? I have tried the ROM 1.72 bootloader but it does not work at all. My bootloader is 1.02.
THe strange thing about this all is that when loaded into bootloader mode, the phone says Serial. When i plug in the cradle/cable, the phone can recognize the connection and it changes to USB. But it is still detected as a malfunctioning device on all 4 of my computers (WinXP x2 Win2k x2).
Help, somebody!
can't you put it in bootloader usb and then run an upgrade ?
M4io said:
can't you put it in bootloader usb and then run an upgrade ?
Click to expand...
Click to collapse
no..what kind of an upgrade would run on a undetected USB connection?
Even mttyl won't work.
So is a general SD-solution available yet? Or should I try by restoring a backup from another XDA II?
Anonymous said:
So is a general SD-solution available yet? Or should I try by restoring a backup from another XDA II?
Click to expand...
Click to collapse
Solved the problem..
Believe it or not, the connector on the bottom of the XDA II had actually had 4 pins twisted down...in particular the USBDATA+ and - pins clamped to ground (i think) thank goodness the device still works.
Managed to restore them to the original position with a blade, tweezers and a very nervous 20 minutes.
Have no idea what a replacement connector would have cost locally here. Probably another bomb (or as the "generic" solution goes.. Err, sir.. We need to replace your motherboard RUBBISH!
I just got my phone back from repair and I'm trying to install HardSPL. The installer for some reason isn't able to tell that the phone is connected and even though the phone says "USB" in the bootloader, HSPL doesn't see it.
HSPL is just stuck saying "Waiting for USB..."
Any hints? I'm using windows 7
pkchips said:
I just got my phone back from repair and I'm trying to install HardSPL. The installer for some reason isn't able to tell that the phone is connected and even though the phone says "USB" in the bootloader, HSPL doesn't see it.
HSPL is just stuck saying "Waiting for USB..."
Any hints? I'm using windows 7
Click to expand...
Click to collapse
make sure u are conected to the internet for driver update
chek your cable ))
make sure that your usb connection is set to active sync (on your device)
I had already tried all of the above and it didn't work.
(with regards to the activesync thing, the HSPL installer automatically took my phone into bootloader mode. So I don't think there was any issue there)
In the end, I just went and used a different computer.
I have a laptop, and i had the same problem. My solution was to connect my phone through another usb port on my computer (main usb port) try it with the other usb ports.
Hope this helped you
sahus said:
I have a laptop, and i had the same problem. My solution was to connect my phone through another usb port on my computer (main usb port) try it with the other usb ports.
Hope this helped you
Click to expand...
Click to collapse
Hmmm interesting....
However, the same USB port on my computer works for flashing ROMs and Radios so I doubt that is the problem. In fact, I used the same USB port for flashing the NRG rom straight after I hard spl'd my phone!
My solution was to just use another computer.
Thanks for your response. Hopefully this thread might help some guy in the future in a similar situation.
However, the same USB port on my computer works for flashing ROMs and Radios so I doubt that is the problem. In fact, I used the same USB port for flashing the NRG rom straight after I hard spl'd my phone!
,
Click to expand...
Click to collapse
actually just cos a port works for flashing means nothing. you can flash and sync through case mounted ports and usb hubs, but hspl won't work on those same ports.
Two days ago I could not use my HD2 as a USB and also it could not be activesync with PCs. I tried to connect it with PCs, laptops, all were failed. I dont know what I can do. All PCs showed " USN device not be recoganised" . Could anyone help me please?
Hi, I can only charge my HTC HD2 phone using the USB port, but I cannot use the usb port for activeSync and USB function (data transfering). I wonder if the USB posrt is dead already?? Why the phone still can be charged via the USB port? Can anyone tell me how to fix this?
Thanks in advance.
I'm sure you have tried to reboot your HD2, but have you also tried another USB-Cable?
Power and data wires are seperated, so it could be possible your HD2 can be charged, but data can not be transfered.
Which OS are you using on your PCs and Laptops? Iguess XP if you are using AS instead of WMDC. You can try to remove AS and install new after reboot.
Virus scanners and firewalls are also known for blocking data transfer sometimes.
mantis123 said:
Hi, I can only charge my HTC HD2 phone using the USB port, but I cannot use the usb port for activeSync and USB function (data transfering). I wonder if the USB posrt is dead already?? Why the phone still can be charged via the USB port? Can anyone tell me how to fix this?
Thanks in advance.
Click to expand...
Click to collapse
Mantis Have you solve your problem? I got same problem,too.after i flash hspl 2.08 .
mantis123, do the following:
1. Disable any antivirus or firewall on PC
2. Delete partnership or reinstall ActiveSync
3. Open task manager on device and kill ActiveSync in Applications tab (if exists)
4. Try to connect.
If that does not work - hardreset the device and try again the same order.
If that does not work - re-flash rom. Try different one.
If that does not work - check the cable. There are 5 pins in outlet - so you have 5 wires inside. See picture attached. You have to check # 3 and 4 contacts/wires.
If everything's good with the cable - go to workshop to fix device.
osprite said:
I got same problem,too.after i flash hspl 2.08 .
Click to expand...
Click to collapse
Kinda coincidence. Flashing HSPL has nothing common with sync problems.
I have this too sometimes. Rebooting both PC and HD2 (soft reset!) usually does the trick to get everything going again.
Cenobite_ said:
Rebooting both PC and HD2 (soft reset!) usually does the trick to get everything going again.
Click to expand...
Click to collapse
These... hmmm.... actually, routine actions - would be done by the user before posting here.... No?
Besides:
mantis123 said:
I tried to connect it with PCs, laptops, all were failed. I dont know what I can do. All PCs showed " USN device not be recoganised"
Click to expand...
Click to collapse
I think he could hardly forget to restart both things before he stated to try other PCs and laptops (in plural).....
After your expert like advise. I use a new cable it's really work and solve the problem.
Many Tnks
AndrewSh said:
mantis123, do the following:
1. Disable any antivirus or firewall on PC
2. Delete partnership or reinstall ActiveSync
3. Open task manager on device and kill ActiveSync in Applications tab (if exists)
4. Try to connect.
If that does not work - hardreset the device and try again the same order.
If that does not work - re-flash rom. Try different one.
If that does not work - check the cable. There are 5 pins in outlet - so you have 5 wires inside. See picture attached. You have to check # 3 and 4 contacts/wires.
If everything's good with the cable - go to workshop to fix device.
Kinda coincidence. Flashing HSPL has nothing common with sync problems.
Click to expand...
Click to collapse
Sent from my HTC HD2 using XDA App
Hi since today when i connect my phone to the USB Cable it's only charging, i don't see USB mode... Did someone have same problem, i looking for solution pls
Can someone tell me in settings>wireless and network do you have USB Settings?
Lenks said:
Can someone tell me in settings>wireless and network do you have USB Settings?
Click to expand...
Click to collapse
Hey!
Nope!
CHEERS!
Lenks said:
Hi since today when i connect my phone to the USB Cable it's only charging, i don't see USB mode... Did someone have same problem, i looking for solution pls
Click to expand...
Click to collapse
Do you have Samsung Kies ?
Sent from my Awesome Ace with fla.sh ROM and TAPATALK
I have KIES, i try on my PC, and on my Laptop. Reinstall KIES and drivers, nothing help. I read on google and i think is a cable problem, (same problem whit other android phones, like HTC) i purchase new one but will came after few weeks, so i need to wait If anyone have problem like this, or have any idea please share...
Typ *#7284# in your dialer.
And set both to pda.
Worked for my galaxy 3!
i think it came different menu... if someone hace other code...
The menu is named: phoneutil
It open "ServiceMode", if someone know proper code for "PhoneUtil" let share
Lenks said:
Hi since today when i connect my phone to the USB Cable it's only charging, i don't see USB mode... Did someone have same problem, i looking for solution pls
Click to expand...
Click to collapse
I have the same problem, it suddenly stopped working without any change in the environment or phone.
Does someone have a solution for this problem?
Thanks!
i had the same problem. I took a backup of the rom with cwm and restored it and it was working fine, dunno how
Guys you need the Samsung usb drivers ....only then ur pc will recognise the phone ...just google "android 2.3.4 for Samsung galaxy ace androidflip.com ..they share the drivers in the tutorial ...hope I helped ...
Sent from my SGA rocking CM7.2 by vo-1 + all-in-one script
Lenks said:
It open "ServiceMode", if someone know proper code for "PhoneUtil" let share
Click to expand...
Click to collapse
*#*#4986*2650468#*#* PDA, Phone, Hardware, RF Call Date firmware info
*#*#1234#*#* PDA and Phone firmware info
async3 said:
I have the same problem, it suddenly stopped working without any change in the environment or phone.
Does someone have a solution for this problem?
Thanks!
Click to expand...
Click to collapse
Ok, It got solved yesterday this way:
You do not need to reinstall drivers on PC.
You do not need to reinstall ROM or anything on your phone.
You do not need *# special codes.
You do not need a new cable or change USB port or change your phone for a new one.
It seems to me that somehow (probably for debugging, connecting and disconnecting several times) the phone locks itself in a state where it is unable to connect again through USB although it charges.
So how did I solve it? I executed this actions several times even in different order some times: disabled debugging, disconnected cable, restarted phone, connected cable, (still not recognizing), tryed to USB Theter (even when the option was disabled), reenable debugging.
Out of nothing i noticed the USB icon was there again in my phone and i was able to debug copy files etc again.
I tried disconnecting and conneceting again and it kept working correctly.
I hope this helps someone else with the same problem and probably someone fixes the bug on the OS.
Cheers!