I have mini s G4, and would like to place radion 2.19.11.
I have tried using radio only rom with shell tool, but same radio version left on!
The flash only takes a few seconds.
Am I doing something wrong?
Should I Hard Reset?
Should I Soft reset?
PLEASE HELP! I am getting too many dropped calls.
Related
I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
mixpro said:
I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
Click to expand...
Click to collapse
You don't have a brick
Load the wizard into bootmode (start and keep voicecommand button pressed until you see a three colored screen)
Then kill active sync (wcescomm.exe in taskmanager).
Connect your device
Load the original rom and flash.
After that you can reflash almost any rom to your G4 with Soft SPL.
Its faster than shelltool
Or you can CID unlock it using hard SPL, and run the Ruu from the ROM itself.
Before using Soft SPL or Hard SPL read the threads first.
Good luck,
EquinoXe
mixpro said:
I'v been up for 24 hours. I have searched, read eveything, DL every tool, rom I could find and I am tired and upset. I have followed every post to the line.
I have a G4. I used the shelltool and flashed the TNT_5.0_Wizard_Professional to it. It booted once and worked great but has never booted since. It gets to the HTC screen. and shows the IPL 2.28.0001 and the SPL 2.28.0001 the GSM 02.25.11 and the OS 6.0.0.0
At this point I don't know what to do to unbrick my phone. I tried to go into bootloader and reflash the ROM but it always gives me a no communication error. Any advice or any one having this problem and had any luck fixing this would be super helpful.
Thanks...
Click to expand...
Click to collapse
Two things:
1- 'No communication' can come from low voltage battery. Be sure to have it more than 60% before changing ROMs
2-The TNT 5.0 is a cooked ROM and is smaller than the Official ROMs.
TNT5.0 - 0x3800000
Official - 0x3900000
Which means that ShellTools can hang because of the size difference.
You don't have a brick
Load the wizard into bootmode (start and keep voicecommand button pressed until you see a three colored screen)
Then kill active sync (wcescomm.exe in taskmanager).
Connect your device
Load the original rom and flash.
After that you can reflash almost any rom to your G4 with Soft SPL.
Its faster than shelltool
Or you can CID unlock it using hard SPL, and run the Ruu from the ROM itself.
Before using Soft SPL or Hard SPL read the threads first.
Good luck,
Click to expand...
Click to collapse
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
mixpro said:
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
Click to expand...
Click to collapse
It's not a brick yet.
Have you tried Mestrini's tip, regarding fully charging the device?
You can also try to use another usb port and better yet, another computer, even if the initial flashing was from the computer you are using now.
Good luck,
EquinoXe
not yet..
mixpro said:
I'v done all that. No matter what I do it just wont load any rom. Just keep getting the message unable to connect.
I am ready to throw this thing across the parking lot.
Click to expand...
Click to collapse
hey,
i have been from that state already..
just use the wizard_love ROM..
yea, they are right.. you have to be in that 3 color screen..
then kill the active sync or uncheck usb connection in connections settings.
then flash the wizard love ROM..
after that, u cud flash any WM6 again..
rizortiz
received a sprint 6800 yesterday.
installed titan_SPL_2.40-olipro.exe
kitchen installed 100%.
after reboot, stuck on sprint logo screen.
attempted soft and hard resets as well as taking the battery out.
phone not recognized by activesync.
looking for some help.
you need to upgrade the radio if all you did was unlock the phone and flash the rom its going to stay stuck at the boot screen until you upgrade to the 3.27 radio
I wish I had a nickle for everytime I saw this "bricked" complaint.
for anyone else out there reading this, please take this as a lesson. Read before you do anything. 3.27 Radio is required and it says that everywhere.
Do not flash your phone if you have not read everything about how to do it.
i'm a noob.
thanks.
hi everyone, can someone please tell me what i did wrong.
I have flashed a few roms before and this time every time i start the 8125 it gets stuck cingular raising the bar screen.
The phone will still do hard reset.
Ipl 2.25.0001
Spl 2.2.5.001
Gsm 02.25.11
OS 11.0.1.1
I tried to do upgrade it to the the TNT 19199 professional wizard v.2. I used the shell tool and dropped the nk.nbf file into the shell folder like i have always done before and this time its stuck at the same screen. I can't connect it to active sync or even the computer to put back the stock cingular rom back in. Can someone please tell me what im doing wrong, from what i understand the phone is not bricked yet because i can still do a hard reset but still sends me back to the main startup screen. Help please.
Stock ROM can be flashed from Bootloader mode, just put your Wizard into bootloader mode (Camera+reset), then run the stock ROM RUU.
thanks helped out perfectly
Same Problem
New to this...Could someone Please give me a walkthrough on how to do this.I can still hard reset.I reset using camera + reset...Brings up r/b/g screen.I don't know how to flash from there.Any help is greatly appreciated.
IPL 2.25.0001
SPL 2.25.001
OS is 10.0.0.10
I took it back to WM5.Seems to be OK.Gonna try using Wizard Service Tool instead of ShellTool.See what happens
You should HardSPL, then use RUU on ROMs without IPL directly.
I got a dopod 838 pro of a friend with wm5 and upgraded it to wm6. This worked fine but i wasn't happy with the way it was behaving so I downloaded a original rom from dopod asia. When I flashed it it completley it **** itself at radio flashing. It now boots and gets stuck on the windows mobile screen and won't do anything, i've tried tapping the screen, pushing every button and hard reset a few times. Could someone please help me, I used this thing every day before it bricked.
If you have Hard sPLed your phone to SPl 2.10 olipro, I'd suggest trying to flash a stock rom with the sd card to see if you can restore your radio rom. You may have corrupted it and it may never work as a phone again. I'd still try the stock rom then reflash what you want if it works... You can find the instructions for sd card flashing on the wiki with a quick search...
Hope this helps... Cheers
All,
I have a verizon xv6800 fresh out of the box. I tried to flash the 2.40 bootloader and it did not go right. I am now stuck on the multi-color bootloader screen and I have tried pulling the battery and the soft and hard resets. I think Windows 6.1 is gone and I can't get any of the solutions to work! Am I bricked? Please help!
Thanks!
-Mark
search for olipro's exit bootloader program and run that, should be right after that i think.
actually being stuck at the bootloader screen isnt a major.. flash to a radio rom that is 3.35.04 or higher and then load a custom OS rom such as dcd's
also refer to the titan wiki for information.