All,
I have a verizon xv6800 fresh out of the box. I tried to flash the 2.40 bootloader and it did not go right. I am now stuck on the multi-color bootloader screen and I have tried pulling the battery and the soft and hard resets. I think Windows 6.1 is gone and I can't get any of the solutions to work! Am I bricked? Please help!
Thanks!
-Mark
search for olipro's exit bootloader program and run that, should be right after that i think.
actually being stuck at the bootloader screen isnt a major.. flash to a radio rom that is 3.35.04 or higher and then load a custom OS rom such as dcd's
also refer to the titan wiki for information.
Related
Hi All,
I tried flash by wizard following http://forum.xda-developers.com/showthread.php?t=298967
Every thing went well but I was not able to HARD RESET. So instead I removed the battery and started it again. It starts up but got struck at screen which says
IPL 2.21.0001
SPL 2.21.0001
GSM 02.19.11
OS 2.18.00
Could some help me what to do now. I read some threads to go to Boot loader screen by pressing "Camera" + "Reset" button and got USB at bottom left and tried RUU with some thing available on forum but every thing failed saying "connection not established"
Please guide me to solve this problem.
if ur device is CID LOCKED "G4" u need to flash the official rom 1st then flash with any G4 safe rom available >>
USING :
ShellTool
http://forum.xda-developers.com/showthread.php?t=293480
or
SoftSPL
http://forum.xda-developers.com/showthread.php?t=329147
Thats the only way for G4 "CID LOCKED"
No...
If OS is not boot up correctly, both ways doesn't work because all of them requires to do in a working OS.
You should find your stock ROM or Wizard Love ROM, use the bundled RUU to flash it so you get the device working again, then use SoftSPL/flash HardSPL and use RUU to flash OS-only WM6 ROMs.
Yes starkwong you are right. I bought my device back working by flashing it with "wizard love" now its up and running. I would proceed with Soft SPL/Hard SPL and then try to flash it with WM6.
i began to upgrade with dcds 2.40 olipro hard spl and after the initial loading was instructed to disconnect device, after reconnting device i ran the rest of the programs rom and such and now i'm left with the 2.40 olipro screen will not reboot. i have tried hard reset and soft reset and even power camera and soft reset keys, nothing has worked yet. please hlep me figure this out and whether or not my device is bricked? also i'm runnig on the alltel network if it helps.
You're OK
You're probably just fine--95% probability--Just go ahead and flash the radio, then flash the rom, and then see what you get.
alright, thanks i'll try that and let ya guys know how it goes
hi everyone, can someone please tell me what i did wrong.
I have flashed a few roms before and this time every time i start the 8125 it gets stuck cingular raising the bar screen.
The phone will still do hard reset.
Ipl 2.25.0001
Spl 2.2.5.001
Gsm 02.25.11
OS 11.0.1.1
I tried to do upgrade it to the the TNT 19199 professional wizard v.2. I used the shell tool and dropped the nk.nbf file into the shell folder like i have always done before and this time its stuck at the same screen. I can't connect it to active sync or even the computer to put back the stock cingular rom back in. Can someone please tell me what im doing wrong, from what i understand the phone is not bricked yet because i can still do a hard reset but still sends me back to the main startup screen. Help please.
Stock ROM can be flashed from Bootloader mode, just put your Wizard into bootloader mode (Camera+reset), then run the stock ROM RUU.
thanks helped out perfectly
Same Problem
New to this...Could someone Please give me a walkthrough on how to do this.I can still hard reset.I reset using camera + reset...Brings up r/b/g screen.I don't know how to flash from there.Any help is greatly appreciated.
IPL 2.25.0001
SPL 2.25.001
OS is 10.0.0.10
I took it back to WM5.Seems to be OK.Gonna try using Wizard Service Tool instead of ShellTool.See what happens
You should HardSPL, then use RUU on ROMs without IPL directly.
My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.
Hi guys I need some help. I have a Cingular HTC 8125, I was trying to upgrade the rom on it to a new WM6 and here is what happened.
I have been researching the topic for about 3 weeks.
Its a G4 Device being upgraded with VISTA w/ Moded drivers for Ative SYNC
IPL 2.25.0001
SPL 2.25.0001
I used the shell tool to install one of the roms waited about 2 hrs and finally noticed that the window was NOT RESPONDING so I had to shut down and start over. The phone got to the second screen but froze there now showing
IPL 2.25.0001
SPL 2.25.0001
GSM 02.25.11
OS 10.1.0.811
On the Cingualr Background, I can still enter the Bootloader screen but nothing else?
Nothing else happens I cant connect the phone to the PC to do anything else.
Is it bricked or not is my question and what can I do to flash OEM rom or something that will work.
I tried OEM Cingular rom but I get ERROR 260 No connection to the phone?
Any help will be greatly appreciated!
Bricked phone
You should had firstly either hardspl or soft spl the phone b4 trying to load any rom
It's not bricked as long as you can see the RGB screen (Colors red, green and blue)showing the same IPL/SPL such as yours; IPL: 2.25.0001 and SPL: 2.25.0001. AND PLEASE BE CAREFUL WITH YOUR DEVICE CAUSE ITS G4 MEANING YOU CAN NOT JUST INTALL/FLASH ROM. Make sure that the Rom you flash not contain G3 IPL and SPL which is 2.xx.001. If so, then you will bricked your device.
Desiji is right, you should install rom with softSPL or hardSPL.
Try to flash the Official Cingular Rom or Wizard Love Rom. If success, then you can install other Rom using what desiji said. Just make sure that its a G4 safe rom. And another thing, try to charge battery using wallcharger not in the device. U need enough battery to perform rom flashing.
Hope this help revive your Wizard.
esdee007
WOW !
grrrrr8,you are a quick learner
CateraMV6
Yeah ! I certainly agree with esdee007 and desiji
Thanks
Hey guys thanks, thats what I thought but I think my main problem is the VISTA I need to get a hold of XP and try all that because the Vista is having issues with connecting to the phone at the moment, I can not get it to show it as a device. It does make a beep noise when you connect/disconnect it so its doing something but Vista is just too much of a pain in the rear to deal with.
Its a good news that its not bicked so all hope is not lost.
What is the opinion on Tmobile WING!? any reviews should I get that phone instead?
BTW where do I find these G4 Safe ROMS? and how do I tell if they have the IPL/SPL in them? Do I need to hack them to tell?
And is Soft or Hard recommended?
YUP ! sure vista is still not compatible for flashing,WinXP is highly recommended and trouble free.
All official stock roms are safe to flash both the devices G3 or G4,secondly,all the latest custom build wm6 or wm6.1 are safe for both the devices,as they don't include any IPL/SPL in them.
If you plan to flash many roms,than 'HardSPL' is recommended,coz its done only once and the device remains semi_Cid unlock untill you personally remove HardSPL,but with SoftSPL,its done everytime you want to flash a new rom,choice is all yours,how you want to go about it.