Related
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
Need some help...
I tried to flash a new Radio on my Hermes (1.40). Actually to reflash it... (Already had it installed, but this is another story)
While flashing I had 0% update... and not moving
Then CustoRUU said it failed... and proposed me to try again... I have SPL-1.11.Oli
So I could easily restart... get the tri-color screen... But whatever I do... I always refuses to flash... never goes further than 0%... And my USB port works on the PC (tested)... and the phone actually sees once I plug (I get USB apperaing when I plug it)
Has anyone experienced this before ? Can someone help ?
Thanks for your help...
Reflashed the OS ROM and at least I can boot... Kind of unbelievable
A real apin anyway... I have the no GSM problem now, but I guess if I reflash the radio it should work...
Alcibiade said:
Reflashed the OS ROM and at least I can boot... Kind of unbelievable
A real apin anyway... I have the no GSM problem now, but I guess if I reflash the radio it should work...
Click to expand...
Click to collapse
Just cannot reflash it
I tried 1.40 again... get stuck at 0%
So I tried to flash 1.38 instead... Doesnt work. I stay stuck at 0%...
Feel really bad now... If someone can help me...
Thanks
Please refer to the unbricking thread dude, read through it all (i know its a long thread but i can almost guarantee that your situation has been adressed.
look at this guide to flash radio using same way expalined for radio 1.38.xx.xx :
http://www.mrvanx.org/hermes_guide/
The guide is also in italian at this link
mrvanx said:
Please refer to the unbricking thread dude, read through it all (i know its a long thread but i can almost guarantee that your situation has been adressed.
Click to expand...
Click to collapse
I went through it... (Btw didnt precise, I have a X01HT)
Since I have Olipro's Hard SPL 1.11 I should not have any problem... I should be able to flash any NBH with another radio. At least so says the Wiki for unbriking
filippodisvevia said:
look at this guide to flash radio using same way expalined for radio 1.38.xx.xx :
http://www.mrvanx.org/hermes_guide/
The guide is also in italian at this link
Click to expand...
Click to collapse
Thanks, but that s exactly what I had been doing several times... The problem being I get stuck at 0% update...
Alcibiade said:
Thanks, but that s exactly what I had been doing several times... The problem being I get stuck at 0% update...
Click to expand...
Click to collapse
do you get the NO GSM error when the device boots?
if so... it sounds like you bricked your radio bootloader, which I'm afraid is unrecoverable
Olipro said:
do you get the NO GSM error when the device boots?
if so... it sounds like you bricked your radio bootloader, which I'm afraid is unrecoverable
Click to expand...
Click to collapse
HI MAN . .
so there is no way to fix it by software ?? cuz i have the same problem and i'v tryed every almost every thing but there is no way to flash radio rom n stuck in 0%
so what u think to do with my tytn , is there any where to send it to to fix it cuz i'v check the market over here n it cost tooo much to fix it around 500$
cheer
werdow said:
HI MAN . .
so there is no way to fix it by software ?? cuz i have the same problem and i'v tryed every almost every thing but there is no way to flash radio rom n stuck in 0%
so what u think to do with my tytn , is there any where to send it to to fix it cuz i'v check the market over here n it cost tooo much to fix it around 500$
cheer
Click to expand...
Click to collapse
nope, if the radio Bootloader is killed, it's buggered.
Olipro said:
do you get the NO GSM error when the device boots?
if so... it sounds like you bricked your radio bootloader, which I'm afraid is unrecoverable
Click to expand...
Click to collapse
Yes I get the No GSM error when booting
Olipro said:
nope, if the radio Bootloader is killed, it's buggered.
Click to expand...
Click to collapse
Then I am dead...
Olipro said:
do you get the NO GSM error when the device boots?
if so... it sounds like you bricked your radio bootloader, which I'm afraid is unrecoverable
Click to expand...
Click to collapse
No chance to fix it ?
I have been watching this thread, Is there a way to avoid this Oli. This has not happened to me but I do want to make sure that I do not run into troubles with future flashing. I hardly post, to busy reading everything and as you can see from my signature I have Hard SPL 1.40.
Thanks
Alcibiade said:
Yes I get the No GSM error when booting
Click to expand...
Click to collapse
The strange thing is whenever I take out my SIM card and put it back I do not get the "No GSM" message. nd the phone works... That's primarly why I tried to update the radio... To fix this annoying problem...
I just tried again... Removing the SIM, puting back, I get the network, can use the phone. And now, and now......... it's flashing !
Waoh waoh waoh... I guess kind of lucky on this... And I a SURE it's nota misplaced SIM that is the origin of my problem... Still flashing now, will tell the result later
Thanks Olipro for your support
Alcibiade said:
The strange thing is whenever I take out my SIM card and put it back I do not get the "No GSM" message. nd the phone works... That's primarly why I tried to update the radio... To fix this annoying problem...
I just tried again... Removing the SIM, puting back, I get the network, can use the phone. And now, and now......... it's flashing !
Waoh waoh waoh... I guess kind of lucky on this... And I a SURE it's nota misplaced SIM that is the origin of my problem... Still flashing now, will tell the result later
Thanks Olipro for your support
Click to expand...
Click to collapse
It does look like I have a Hardware problem no ? Or not far from it... Seems like I have to take out my SIM card quite often (Not every reboot, but nearly...)
If anybody experienced the same kind of trouble... I'd be happy to hear from them
Olipro, could it be tht the radio bootloader is corrupted, but still working from time to time ? Or maybe I have a hardware issue ? Someting I can try to check about the radio bootloader (Or try to fix it) ?
Otherwise since I dumped the original ROM of my phone, I ll learn how flash it back (If I remember well it's kind of a pain, since the image is not similar to the ones we usually flash from this forum...) and will bring it back
My worry is that the flash fails in the middle and I get stuck... And not sure my phone maker will like "Hard SPL"... But I should not remove it... too risky...
Anyway I'd rather avoid that so if anybody has a clue of what may have happened to my radio booloader (Or if it's something else...), I'd love to have some advice
Lurch3559 said:
I have been watching this thread, Is there a way to avoid this Oli. This has not happened to me but I do want to make sure that I do not run into troubles with future flashing. I hardly post, to busy reading everything and as you can see from my signature I have Hard SPL 1.40.
Thanks
Click to expand...
Click to collapse
yes... I think if the Radio BL is the same or older then the process is skipped, therefore, and again, I *think* if you're BL0108 then you're safe from this.
Thanks for the info Oli.
Even in this configuration (ie moving the SIM or rebooting until I dont have the "NO GSM" message, my 3G / HSDPA connection drops frequently and I have to reboot... Sometimes the phone works, soemtimes it doesnt
Olipro: this symptoms are symptoms for what ? Broken radio bootloader ? (But as it seems not 100% broken...) Or something else ? Do I have a chance to fix this ?
to get out of it, is very simple... remove your minisd then press "ok"+"power"+"reset"
it should work unless u damaged your spl. if you damaged you spl, copy original one from RUU_Athena.... and rename it to ATHEIMG.NBH then copy it to you sd, then press "ok"+"power"+"reset"
i'm not sure it all will work for everybody, but thats what i tried and it did work for me...
good luck playing with your athena, but be careful
it should work unless u damaged your spl. if you damaged you spl, copy
original one from RUU_Athena.... and rename it to ATHEIMG.NBH then copy it
to you sd, then press "ok"+"power"+"reset"
Click to expand...
Click to collapse
I tried this and still in white screen(after change from Spanish to English and disconnect error occurred).
Hi,
i have a uk ameo from tmobile, will it work if i take the nbh from htc wwe version ?
My case in detailes...
I have original HTC Advantage 7500 not branded with Spanish windows . After tried to update with English RUU my htc Advantage stuck in 3 colors boot-loader mode. Any resets(soft, hard, boot-loader) not help.
Than I find this suggestion here I tried it and it help:
I think you are not stuck in bootloader, I think you are stuck in the Flash
ROM utility which has colors and not just the Dopod logo with a black scree.
If this is the case, here it is what I did to solve this:
I downloaded ruu_athena_dopodasia_wwe_1.24.707.3_105_6275_1.32.
00.10_108_ship, which you already did.
Decompiled the RUU_signed.nbh contained inside
ruu_athena_dopodasia_wwe_1.24.707.3_105_6275_1.32. 00.10_108_ship with
dutty's good NBH tool found at: http://forum.xda-
developers.com/showthread.php?t=296316 then I created a new RUU_signed.nbh
with the same files but it didn't allowed me to insert some items like the
SIRFBootLoader.nb and some others, so I started executed the
ROMUpdateUtility.exe again and it stopped again at 1% but with a different
error "Corrupted ROM Image" and suddenly! My device was taken out of the
Flash Utility to see the bootloader screen again! Wow! What a relief!
Click to expand...
Click to collapse
this is done!
after my Spanish OS reloaded and I can to do ActiveSync with PC - Than I find this suggestion in this thread and I tried it and after 5 min connecting error occurred . After hard resetting after this "update", after the HTC boot screen I just get a white screen. The HTC does make a sound as if it's working and BT and WiFi leds blink. When device connected to PC the HTC does make a sound as if it's working, but the ActiveSync in PC write that can't to connect to mobile device. And I just can't see anything.
Now I can't find Spanish HTC Advantage 7500 not branded RUU in all World.
Any ideas.
I succeeded with mine
Thank you. I was wondering whether I had actually bricked my athena, but then your tip helped me out....
Ken_xda said:
Thank you. I was wondering whether I had actually bricked my athena, but then your tip helped me out....
Click to expand...
Click to collapse
Good Tipps ! LOVE THEM !
thanks for help !
Hi,
I have used (installed) the Wizard love on my Qtek 9100 (O2 xda Mini s)
But now, when it starts up, it shows the wizard love splash screen, or image.
Is there a way to change it?
I would like to put back the O2 image. (i already found a O2 nfh file, but no tool to update it on my device)
can someone help ?
thanks.
stefke1974 said:
Hi,
I have used (installed) the Wizard love on my Qtek 9100 (O2 xda Mini s)
But now, when it starts up, it shows the wizard love splash screen, or image.
Is there a way to change it?
I would like to put back the O2 image. (i already found a O2 nfh file, but no tool to update it on my device)
can someone help ?
thanks.
Click to expand...
Click to collapse
here it is.....
download a new ROM (does not matter which one you pick) and then....
copy/paste O2 nfh file in the folder with the RUU.
... ok now "flash" and the screen should be there
Got it? if not, send pm
good luck°!!!!
i tryed that, but, still, it stays WizardLove
stefke1974 said:
i tryed that, but, still, it stays WizardLove
Click to expand...
Click to collapse
is your wizard HARDSPL? or softspl?
seems a little weird.....
LOL
anyway good luck!
i use hardspl
Try this one.
Thanks a lot IT WORKED
only, your update tool didn't work.
I just copy the file nk.nbf to my update tool, and now it is done, i have O2 splashscreen again.
Thanks a lot for your help.
By the way, is there a update tool working with Windows 7 ?
I updated my phone (HD2 T-mobile) via internet website and when I finished the updating process, the phone did not work at all.
I tried more than once to switch it on, but it didn't respond. I took the battery out and put it in again, but nothing happened.
When I connect the phone with the charger, the charger light doesn't become on.
It seems that the phone is dead!!!. What do you suggest to solve this problem? If you think it is a hardware problem, what is the name of this hardware
Tray update ROM again
It dose not Enter in bootload mode
How I can apdate rom from diffrent way
What rom did you flash? If it isn't a tmous rom then the phone is destroyed.
HD2-RUU_Leo_HTC_ARA_1.66.415.9_Radio_15.37.50.07U_2.10.50.08_2_Signed_LEO_Ship
This ROM's name
Please support us with a bit more of information.
You´ve got a T-Mobile device and flashed it with a different ROM for a HTC device without branding.
But what did you meant with "flash via Website"? How did you really flash (via Active Sync or via SD card)?
Did you install HSPL or at least SSPL first?
I Flash it via Active Sync
yes I Installed HSPL But sspl I didn't Install
Its dead,the radio in that rom has killed it.
Only options are JTAG or replace mainboard
Though it is strange that the filename says 2.10.50 for the radio version,since 1.66 roms usually come with ..51.. radios,which kill tmouses.
If it really is a ..50.. radio in a 1.66 rom then a tmous should boot but hang at splash, yet you say yours just won't start, so I suspect a typo in the filename. (Not your typo,I can see lots of references to that filename online.)
I am download this rom from HTC site
Mo7ammad_89 said:
I Flash it via Active Sync
yes I Installed HSPL But sspl I didn't Install
Click to expand...
Click to collapse
You said that you have a T-Mobile device, but you didn´t tell that it is the US version of it. Is it or do you have the European version?
If it is the USversion you really flashed the wrong Radio ROM.
For the European version it would be no problem
no My Mobile Is Us version
Mo7ammad_89 said:
no My Mobile Is Us version
Click to expand...
Click to collapse
So it seems you have bricked your device, I would recommend to bring it to a service point and hope that they do not notice what you have done.
Perhaps this thread is a last chance for you:
http://forum.xda-developers.com/showthread.php?t=668347
Good luck!
Thank You My friend But This chance Is Impossible becuse It's need to Enter bootload mode and I can't Enter It
check the pins where the battery connect they bend very easy so you dont get a connection the red light will come on when u charge and the phone wont boot! there are three pins make sure they are all makeing a connection! Its very common!
I am sorry but I don't understand you very well can you explain more please
Mo7ammad_89 said:
I am sorry but I don't understand you very well can you explain more please
Click to expand...
Click to collapse
In other words:
Take out your battery and check the contacts between battery and the deviceframe. Is any of them bent?
No It's Not Any Of Them bent I think
but why you ask About It
AM I can repair My Mobile by them
And If you can explain for me by picture I well be glad
Mo7ammad_89 said:
No It's Not Any Of Them bent I think
but why you ask About It
AM I can repair My Mobile by them
And If you can explain for me by picture I well be glad
Click to expand...
Click to collapse
Sorry, it was not my idea but from b3ltazar. His thought was that your device might get no power to work.
I recommend once again to bring your device to a htc service center in order to repair it. In my mind you seem to have an hardware issue