Hi Guys,
Need your advise, I've tried to reload the PDA Viet temp on my device so that I could reload the 4.0.0.6 ver again. The rom works great but some how on the 2nd day it start to be power draining on my 818Pro. was going to reload to play as plain before any apps installation to see if its apps issue and got stuck at boot loader.
Issue Now:
1. on running the device now it goes into boot loader and when connected.
2. doesnt seem to have any OS install and when Hard reset goes to bootloader too.
3.when try to load the ROMUpgradeUtility_NV_G4 fail to connect.
4. Now even when in Boot Loader Screen, the device goes on and off USB connection. making it impossible to transfer files to device.
Please Advise.
Thanks in advance
Try to push/hold camera, comm, and reset button, then release reset and comm but hold the camera, it will be go in the bootloader screen. At this point connect the usb cable and wait until the connection is done.
Are you sure your pda is G4?
thks some more light to the problem both hard and soft rests gives me bootloader but its turn on and off on the USB connection and last check on power is @ 90%
skyhigh75 said:
thks some more light to the problem both hard and soft rests gives me bootloader but its turn on and off on the USB connection and last check on power is @ 90%
Click to expand...
Click to collapse
Hi All,
Just like to encourrage all to be persistent on resolving the issue, think my issue had been resolve, not sure why the batt hard to be charge for bout 6-8hrs by Charger(not USB connection from Computer) almost like initial charge to be able to last through the step one downgrading to wm5.
Previously I charge for bout 4hr via charger and it didnt work, but since there's not new solution I persisted to charge for a longer time and rest before I try again and it work. Thanks for all's contribution the the solutions.
Related
my son's wallaby is having a mid life crisis!!, will NOT turn on at all, the screen is in dimmed mode, screen taps/menus etc etc not working, it is just displaying the message:
Upgrading...
will take about 5 minutes.
Warning: do not remove the
USB/serial connection or power
adaptor from the pocket PC.
problem is that this message has been displayed constantly for the last 24-30hrs!!, have tried a soft re-set...nothing, then tried a hard re-set...nothing, its showing full charge, and have tried removing the SIM and SD cards as well as doing re-sets...nothing!
Please Help!!
Thanks guys.
The problem is that you propably removed your XDA from it's cradle during ROM flashing.
Can you acces bootloader (hold power then press soft reset button) ?
...Not tried that, will give it a go,
thanks for the info.
..OK, I managed to get the boot loader screen up, and ran thru the checks...all appears ok, but none of the tests relate to the OS?, so when all had been checked, and I came out of the loader screeen and turned it on again, it went back to the "upgrading..." as above, just cannot get the windows menu up at all, and activesync doesnt recognise what device it is, but activesync works perfectly on mine..........is there another level/setup program that can be acessed??
cheers guys.
So, after having access to your bootloader reflash your device using SD-Card and bootloader.
Process is described in the wiki of often here in the forum...
Stefan
Ok i have a MDA, i updated the rom, and now it wont turn on at all, But when i plug it into the wall charger it comes up with bootloader, Well when i unplug it it just shuts off, try pluging it into my Pc it wont turn on, Only turns on with wallcharger, I am need to find a way to get back to bootload when its usb connect so i can flash, Can anybuddy help And yes i did search before i post, sorry i am in a panic..
deathblooms237 said:
Ok i have a MDA, i updated the rom, and now it wont turn on at all, But when i plug it into the wall charger it comes up with bootloader, Well when i unplug it it just shuts off, try pluging it into my Pc it wont turn on, Only turns on with wallcharger, I am need to find a way to get back to bootload when its usb connect so i can flash, Can anybuddy help And yes i did search before i post, sorry i am in a panic..
Click to expand...
Click to collapse
There are 2 ways I can think of to fix this. One way is to charge the phone with the wall charger first. Hold the camera button while pressing and holding the power button. This should put the device in bootloader while not plugged in to the wall and get the PC ready before connecting the USB to the phone. Make sure you have a full charge before you do this because it sounds like your battery died while flashing. If you do this, you should be able to get it connected to a computer long enough to flash it back to normal.
Seccond option, if battery will not charge in bootloader mode or when device is turned off, buy new battery and then follow steps above.
I hope this helps... I personally have never had this problem before.
No connection in bootloader mode
After a rom update has interrupted by 96% (and did not finish) I have no chance to connect my mda vario to my laptop. I still come to bootloader mode but no step further.
Have anybody an idea to solve this problem. Is there any other chance to get a connection to flash the rom again?
Many thanks in anticipation for any assistance!
Frisvo
Could anyone help me?
When I turn on the bootloader mode and connect it to pc,it won't make any connection and the red light won't turn on to..
Any suggestions?
I can't use my device because I can't flash new windows...
Could anyone help me?
First of all I’m running XP, and Active sync.
I used Soft SLP- VO.1 , I copied the NK.NBF
From a G4 safe rom into the soft slp folder.
While stuck in boot mode I did a hard reset,
Pluged in the usb and waited for power up.
Then I held the power button down and watched
Active sync try to connect at the same time started
Soft SLP . When active sync stopped I released the power button and then followed the instructions as normal. The phone went into white mode and copied all 100% but it still went into boot mode after it rebooted, but I was able to connect with the phone again. Now all we need is someone smarter then me that can figure out the rest of it. At least there is still hope for the dead ones.
i have sprint touch pro CDMA with new energy rom. i tried to sync it with my laptop. phone and laptop both hanged. i resetted both. laptop started properly.
but TP have problem. its struck on start screen with TOUCH PRO and radio and other information. its not moving ahead. the other problem is that i cannot enter booloader as my volume down button is also not working. i am really in a fix over here.
i need to start my phone. last night also, it stuck at start screen but when i press reset button, it started. but today its not going beyond start screen.
i tried all the possibilities like connecting to different PC, same PC, different USB, removing SD card and then resetting, but no luck..
please help.....
thanx a million in advance.
csmartly said:
i have sprint touch pro CDMA with new energy rom. i tried to sync it with my laptop. phone and laptop both hanged. i resetted both. laptop started properly.
but TP have problem. its struck on start screen with TOUCH PRO and radio and other information. its not moving ahead. the other problem is that i cannot enter booloader as my volume down button is also not working. i am really in a fix over here.
i need to start my phone. last night also, it stuck at start screen but when i press reset button, it started. but today its not going beyond start screen.
i tried all the possibilities like connecting to different PC, same PC, different USB, removing SD card and then resetting, but no luck..
please help.....
thanx a million in advance.
Click to expand...
Click to collapse
Even im facing some issue with Energy's New ROM cookie 2.0 touch glass 0ct 14.
My cell got stuck when i was rebooting the cell. After that when i boot the cell it will get stuck at main screen (Touch Pro logo with red color Text). I left my device like that.After few minutes(more than 10 minutes) when i checked, my device was in main screen and i was able to use it ..
I will flash the old ROM once i go back to home today.
And regarding entering into tri color bootloader,
I am using the mini usb cable ( not htc's usb cable) to connect my device to PC, and it works fine including sync,charging,storage etc
- i switch off my device
- connect my device to PC using MINI USB cable
- It automatically switches on the phone and goes to bootloader screen
PS: i do not press any button, not even power on button
Please some one confirm if this is normal behavior or only it is happening only with me ,
Regards
happy20b said:
Even im facing some issue with Energy's New ROM cookie 2.0 touch glass 0ct 14.
My cell got stuck when i was rebooting the cell. After that when i boot the cell it will get stuck at main screen (Touch Pro logo with red color Text). I left my device like that.After few minutes(more than 10 minutes) when i checked, my device was in main screen and i was able to use it ..
I will flash the old ROM once i go back to home today.
And regarding entering into tri color bootloader,
I am using the mini usb cable ( not htc's usb cable) to connect my device to PC, and it works fine including sync,charging,storage etc
- i switch off my device
- connect my device to PC using MINI USB cable
- It automatically switches on the phone and goes to bootloader screen
PS: i do not press any button, not even power on button
Please some one confirm if this is normal behavior or only it is happening only with me ,
Regards
Click to expand...
Click to collapse
i think its related to ROM. one 1st night, it started, but form last 2 days, i have kept it on for long time, but no result. will try again.
csmartly said:
i think its related to ROM. one 1st night, it started, but form last 2 days, i have kept it on for long time, but no result. will try again.
Click to expand...
Click to collapse
Al d best , Ryt now i hav flashed Energy GTX sense2.5 Rom and going smooth. try flashing other Roms.
Regards
happy20b said:
Al d best , Ryt now i hav flashed Energy GTX sense2.5 Rom and going smooth. try flashing other Roms.
Regards
Click to expand...
Click to collapse
no luck... nothing happens...
if i remove battery and put again, its not going to bootloader on connecting with pc. only it shows that battery is being charged by flashing on round button...
csmartly said:
no luck... nothing happens...
if i remove battery and put again, its not going to bootloader on connecting with pc. only it shows that battery is being charged by flashing on round button...
Click to expand...
Click to collapse
Hmm , r u using usb mini cable or extusb cable from htc ?
happy20b said:
Hmm , r u using usb mini cable or extusb cable from htc ?
Click to expand...
Click to collapse
i tried with mini usb cable provided by HTC and also other make mini usb cable. but no luck
I doesn't want to start..... Only shows battery icon when charging.
if you connect tab in pc usb,your pc recognize it?
Digital @ 961 Tablet Stuck in Boot Loop
vedran.cvetkovic said:
if you connect tab in pc usb,your pc recognize it?
Click to expand...
Click to collapse
I am experiencing the same problem...i believe they call it a boot loop where the start up screen never dissappears to bring you into the actual op. system. Is the only answer to download new firmware or is there a hard/factory reset that does the trick? FYI My computer doesnt recognize the device even when plugged into my mac via usb cable. I tried all I could find on key combos and unlocks for resetting the device but none of them worked. This is the second time this has happened. The first time was an easy factory reset fix pressing both the volume + button and the power key (or was it the volume -? I cant quite remember) for 15 seconds then wiping cache and data and restoring to factory defaults. Why is this same action not working this time when performed in the same way as I did when I fixed it the first time?
Please help, anyone, if you can.
Thank you.
It sounds like you might have tampered with the rom, or something you downloaded tampered with it. That's the only way I can think of as to why the factory reset would not be working. Other than that, potential hardware damage is possible. Before I help, I need to know what model of Digital2 tablet you're using. If you still need help with it, that is.