It want do anything anymore. When i turn the mda vario on the bootloader shows up all the time (the rbg colored screen). I just can't do anything with it.
I tried wizard_love rom but i don't know how i can do it, cause in boatloader my phone wont connect with sync.
Can someone please help me cause i am a bit hopeless.
Thank you very much I appreciate it a lot.
G4 mda vario
I had the same problem with my O2 XDA Mini-S.
While the device is sitting with the RGB screen install the latest WM5 ROM from T-Mobile for your device.
I just loaded my O2 WM5 ROM back in and it came back.
If it won't let you install even the T-Mobile ROM then the device may be goosed.
Be careful
elataster said:
It want do anything anymore. When i turn the mda vario on the bootloader shows up all the time (the rbg colored screen). I just can't do anything with it.
I tried wizard_love rom but i don't know how i can do it, cause in boatloader my phone wont connect with sync.
Can someone please help me cause i am a bit hopeless.
Thank you very much I appreciate it a lot.
G4 mda vario
Click to expand...
Click to collapse
Read "Possible Reviving Techniques in the Wiki"
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
Good luck!
close wcescomm.exe in taskmanager
Try running the ruu again.
Dont Use Vista.
Its easy. If you wizard is on bootloader mode just do the following.
Use a computer using Windows XP, perhaps your problem is that you are using Windows Vista. So try using a pc using XP. Then remove the sd card if you have one. Run the updater of wizard love, take a cup of coffee return 10 minutes later and there you go.
Do a Hard Reset after flashing and you now have a revived wizard.
Related
Hi
I was given an Orange SPV M600 running WM5.0 I foolishly thought I would be able to unlock it to work with my T-Mobile sim (the only network I can get coverage at home) I ran an unlock tool from en.pdamobiz.com
http://files.pdamobiz.com/c/PDAMobiz.com_ProphetAKU2_unlockCID.rar
I managed to get to through to the completion of the Downgrade.bat process. I was then asked to sofdt boot the M600 but it now cannot be found by Activesync. I was unable to successfully run Unlockcid.bat and now it just boots to either the 'Orange' screen (displaying IPL 2.10.0001, SPL 2.10.0001, GSM 02.07.20 & OS 1.0.13.21 - the new OS I believe) or the 3 colour screen (displaying IPL 2.10.0001, SPL 2.10.0001) if I hold down the camera button.
Windows 5.0 has gone or is unreachable but I am assuming it can't be completely dead as I get a noise when connecting/disconnecting the USB lead....
Is this false hope? Have i killed it after 2 days of ownership??? Should I have attempted this process with very little tech knowledge - me thinks YES!
I would be eternally greatful to anyone who can help me out of this black hole..... I just need pointing in the direection of what stage the M600 is at and how to get it running on my T-Mobile sim.....
Thanks in advance
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
The GOOD news is No you haven't killed it. It seems you have wiped the operating system from it. I would sugest searching for RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe down load it and then get your phone to the multi colour screen before running the download. This should then update your phone
when I tried to unlock my phone, I couldn't get it to unloack at all till I put a orange pay as you go sim in the phone and registered the sim with orange then it unlocked first time.
Killed prophet reborn!!
Fingers666 said:
hi there, try going into the bootloader screen, when you connect the usb cable it should show on the bottom off your screen. then try uploading the orange rom you can find on the wiki page. if this works then try using the loki unlocker which you should also be able to find on the wiki page. i used the loki tool and it unlocked first time. hope this helps. let me know how you go.
Click to expand...
Click to collapse
Spot on. Thanks so much for the advice. Fingers666 & jazpa !! I'm back on track. M6000 is now communicating again. WM5 is resident. Just need to unlock the sim and I'm away. [email protected] tried loki 3.0 amd 3.0a with both Activesync 4.2 and 4.5 respectively without any luck so I've just spent £5 a http://www.unlocking.org.uk/ as they say they can unlock a G4 ver. We shall see!! Great help though and THANKS again to both of you
Please Help Meee!!
Hello i was wondering if anybody could help me.
I want to unlock my orange SPV M600 for free.
If there are any safe and free websites that anybody knows of could u please tell me.
Thank Youu!!
James Thomas
Download Lokiwz, it is quite easy to locate. Inside the folder you will find 1 or 2 cab files, copy these to your storage card and run them on your M600. Now run Lokiwiz from your PC, after around 12 minutes, it will display your sim unlock code. Switch off your M600 and insert the sim you want to use, at the prompt, enter your code lokiwiz generated. For around 2 minutes the phone will seem to have no signal, then it will connect.
Worked first time for me, my M600 was locked to Orange, now it works great with O2.
wonderful works great with G4
thanks
mike
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
http://forum.xda-developers.com/showthread.php?p=3909674#post3909674
HERMES (htc tytn) UPGRADE FAILURE
REPORT
Hi all of you!
I have a Hermes (HTC Tytn/ Orange SPV M3100) and i succesfully tried a lot of ROM’s until these days..
But, this happened:
During upgrade of a ROM, i made the mistake to disconect the device from the PC..
And, now the problem is that i can’t boot ANY OTHER ROM!
I can enter to BootLoader , where i see
HERM100
I PL – 1.04
HERM100
SPL – 2.03
ALSO, i CAN connect to PC (it displays „usb” & i see it on Device manager)
(PC run Vista Ultimate 64 bit).
But, when i try to upgrade ANY ROM , the process starts, BUT STOPS at 0% ? .
I searched & read 4 days for a SOLUTION to make my phone alive again..
Can anyone tell me what to do?
Is a REAL solution for this issue?
Please reply.
Thanks!
i GUESS YOUR BATT IS ALMOST DEAD!
Hi dude... does your batt is higher than 50%? the process will not continue if yuour device is under 50% maybe it is beacause you cant charge it in Bootloader. keep it higher than that... if not the case... i guess you will ned to clean it with mtty....
Just search something like that... im for sure there is a way to make it... use the stripped att rom
AND TRY WITH IT ALWAYS!!!
never but never! when you got a problem in upgrade NEVER do a hardreset.... just softreset... keep it on mind... try an XP machine get it wherever you need to get it!
thanks
..a lot for the reply!
i tried on a XP-PC, because mtty don't work in Vista (Ultimate x64)
i followed ALL the instructions..BUT..
..the problem persists!(
thanks for the idea of battery i will try again, with full of..
also, i will try some ROM's without radio's..hope that help..
BTW:
in mtty shows that the device is CID locked with:
"ORANG008"
i downloaded the last ROM for Orange 008, and tried of install...BUT..nothing!(
any other sugestion, please?
thanks again!
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse
Hi. I have searched the forums, but haven't found the answer I have been looking for, so sorry if this is a repeat.
I am working under Windows 7, installed VMWare and XP Pro on it, and easily installed Hard-SPL and Cracings 6.5. When I went to upgrade the Radio, I was sure to download one without SPL and IPL. I tried to upgrade, but it hung at 2% for at least 5 hours. (I knew it was bad in 2 minutes actually, but decided to wait). Now it will turn on, but to the tri-color boot screen. Tried hard reset (although I didn't really expect it to work). Is there anything that I can do? It shows when I connect it to usb, both on the phone and on the computer.
It is FAR out from under warranty, so thats out, but if there is anything I could try, I would be much obliged for pointers. Thanks a lot!
-Jotek
You need to make the update with RUU 2.5.2
( http://forum.xda-developers.com/showthread.php?t=314952 ).
Try it, if even that does not work (for me it works only with wizard_love ROM
( http://forum.xda-developers.com/show...293480&page=21 loca's post), but not with other cooked ROM's) then you can try WST wizard service tool
( http://forum.xda-developers.com/showthread.php?t=329170 ) to unpack the nbf and load only the OS ROM.
Thanks for the info.
I will try it later this weekend when i get time! (moving to new apt.... sigh... can't feed the addiction)
-jotek
If Tri Colour Screen WST needs to boot into WM OS surely???
How can you use WST if only on bootloader. Please explain as I have similar issues...
Dilbert
I had exactly the same experience as you: Hard-SPL followed by Cracing and then the tri-color screen. This thread helped me revive my G4.
http://forum.xda-developers.com/showthread.php?t=442126
Hey I am having the same problem but with my G3 att 8125. I flashed to 2.26 which I always do before installing any rom then installed X2A Haseebs Iphone Killer and it stalled at 57% for over an hour so I unplugged it and hard-reset it. I have installed this rom about twice and it works fine. Now my phone starts up and goes straight to the Tri-colored bootscreen. When I plug the phone in it displays that it is connected via USB but the computer doesnt recognize it. IPL 2.26, SPL 2.26 as displayed on the screen. PLEASE HELP!
Hi all, I've got the exact same problem as Quadzilla has - any help would be much appreciated!