when i want to open mtty.exe . i couldnt see usb port. program said that usb port couldnt open. ????
why :
do you know::
i only see active com3 but coudlnt see usb>
thanks
qrshad said:
when i want to open mtty.exe . i couldnt see usb port. program said that usb port couldnt open. ????
why :
do you know::
i only see active com3 but coudlnt see usb>
thanks
Click to expand...
Click to collapse
I get this sometimes. I didn't know if it was because I am running it under a virtual windows environemtn on a Mac. What I do to get mtty to recognize my port is this:
1. Start ActiveSync
2. In ActiveSync press "connect" or search for connected devices or something like this (since you are in BL mode, AS won't see the device, but it will poll all the ports, effectively making the USB port visible.)
3. While AS is searching the ports, launch mtty and choose selection box for port.
4. Voila' The USB port is usually visible.
If that doesn't work on the first try, a few more tries usually gets it working.
vista problem?
I suspect you are running Vista. You need to rollback to an older wm5 driver in order to "see" the port.
Regards
Related
Hello,
after flashing many, many roms I am not able to flash any more roms....
The problem is: my bootloader stays in SERIAL mode and won't go in USB mode.
I had this problem somethimes before, but after some resetting(PPC and PC), swithing USB cable into antoher USB port after a while he did go into USB mode. But this time nothing works...I tried it manually(power button + ok button + soft reset) and with active sync...but nothing works for me.
I have tried searching the forum, found some articles mentioned it, but no solution.
Anybody else had this problem? My bet: it's a PC problem.....but don't know the solution
Info:
Herm300
IPL-1.04
SPL-2.10Olipro
Current rom: Pandora build 1825
<edit>
PC: Windows XP
tried 2 different USB cables
tried all USB ports
</edit>
Problem Solved !
Solution: reinstall active sync.....
1. Uninstall Activesync 4.5 from Control Panel | Add/Remove Programs
2. Reboot your PC
3. Check to make sure \Program Files\Microsoft Activesync no longer exists - delete it if it's still there.
4. Make sure your phone is NOT connected to your PC and re-install Activesync 4.5
5. Reboot your PC (sorry if this is a bit tedious )
6. Connect your phone directly to a USB port on your PC, NOT VIA A USB HUB!!!
7. Activesync should now detect your phone and start the "Create new partnetship" wizard.
Fine, when problems are solving itselfs, flashing time again, and again and...
i was trying to upgrade the HTC offical ROM. but my hermes was bricked and stuck on the blue windows logo screen now. please help me
(it display NOGSM on the dopod logo screen also)
i have no any idea now and my hermes without the KITL mode
so what can i do .plz help me
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
5. You should see a white screen, hit enter and you should see a prompt like this: "USB>"
6. Type set 14 0 (do not copy and paste!!!) and hit enter
7. Soft reset with stylus
8. OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore!
9. if it doesn't unbrick, repeat all the steps but with the command set 16 0
I want to add something here that worked for me. Tried steps above but it didn't work. So what I did to get mine going again:
ciaoo kB
kb_lejardinier said:
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
ciaoo kB
Click to expand...
Click to collapse
when i go to step 4 and hit OK, the mtty popup a dialog box said "USB port can not open"
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
ocguru said:
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
Click to expand...
Click to collapse
really? i haven't try , i am afarid it will become more serious
but what is your problem previously? why you bricked your phone?
i was trying to upgrade HTC offical ROM and bricked.
THX
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
ocguru said:
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
Click to expand...
Click to collapse
i read this post
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
my hermes is same as the bottom situation of the above page now
SPL2.03,no boot OS, no GSM, bricked while flashing OS, but my hermes
can not switch to KITL mode , so i have no any idea
do you have any suggestion for me?
THX
turn on your phone..connect your usb cable..see if u have any connections with activesync..
ocguru said:
turn on your phone..connect your usb cable..see if u have any connections with activesync..
Click to expand...
Click to collapse
sorry , but it has no any boot OS thus Activesync can not recognize my phone
Apologies but have scoured all the threads and cannot seem to get to a straight answer!
Have a tocuh-dual which I attempted to update to the latest ROM from HTC and now I have the "tri-colour screen of death!) and can get no further,
The screen shows in thered band - RUUNBH | NIKI100 | SPL-1.16.0000 | CPLD-4. The white band shows "serial" and when I connect the USB lead it shows "USB".
But the PC does not recognise it at all and when I try to load a ROM or run MTTY nothing is found. How can I run a program on the touch if the PC will noit see it through the USB connection?
Any ideas?
Does your PC have active Sync installed? I had a similar problem when I installed a broken rom that would not boot up. I did a device reset using the stylus in the whole next to the USB, while holding the camera and power button to boot into the tri color screen. Once hear i plugged in my USB cable and ran a ROM install.
I hope this helps.
uncheck allow usb-connection in Active Sync
run mtty connect by USB
type "boot" without quotes.
same problem
i have got the same problem and can't get out of the tri-colour.
I try to connect with mtty and it says usb port cannot open. my pc can recognise it and in da phone it shows usb though, i don't really know why its not taking. if i type "boot" in mtty what will happen? cos when i click on com3 its opening but when i write "boot" nothing happening even with boot. any ideas guys? how to solve the problem????
Regards
u have to unckeck allow usb connection in active sync! then u can connect with mtty
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
use xp
bodonline said:
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
Click to expand...
Click to collapse
Use xp mate, cos vista has got some problems. normally for unlocking and upgrading i use xp. blow up the vista .
Regards
I will crank one up and let you know how it goes!
kill the task in the Task Manager... then u can connect with mtty
Tried killing the process but MTTY still says "USB port cannot open" - no idea what else to do?
If any Program use the USB Port ... no other Program can use the USB at the same time!
HI !
I have an HD² with official Operator's ROM and my HD² never sync with my computer.
I want to know if it's possible to Flash everything without any sync (only by SD)?
Thanks a lot for my LEO
settings menu all settings connections connections usb to pc, untick "faster data". restart the pc, restart the phone.
it should now sync fine.
Thanks for the Answer, but I've already do this and the results is the same.
Sorry about my English cause I'm French
Go into Bootloader Mode (hold Volume button down while switching on the phone). You will get a tri colour screen with the word 'Serial' at the bottom of it. Plug in the USB calbe and it should change to 'USB'. If this happens then you can run HSPL and then ROMs - just ignore the conditions about making an ActiveSync connection prior to running.
I've already try this
But not exactly how you say.
I've plug the in the USB calbe when the HD2 was Off, and after loading the bootloader.
And nothing was happen.
Juste the 3 colors and the SPL version but never "USB" or "Serials", serial appears only if I don't plug the cable.
Load it into Bootloader Mode, then connect the USB cable - and see if the 'Serial' changes to 'USB'. If it doesn't, then you have a hardware problem (phone or cable or computer).
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Sph1nxXx said:
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Click to expand...
Click to collapse
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
samsamuel said:
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
Click to expand...
Click to collapse
I've already Try on another computer.
I've try with my seven OS, and with XP OS.
The problem is the same.
But when I plug the USB cable, the computer says "unknown Device" and it's the same on different computer with different cable...
I think my HD2 mother card is probably broke for this.
i own an Xperia neo v and am trying to unlock it... I chose the test point method as depicted in the noob's guide which i found in the xda forums... it says to attach the test point to the ground (which i did using a wire and a pin) then connect the usb cable... while windows is searching and installing device detach the test point and windows will fail to install a driver which u then manually install from s1tool...
The problem i am havin is that when i attach the usb cable to the phone my computer doesn't seem to sense my phone at all... i've tried it on both my laptop and desktop and it's the same in both places... can anyone shed some light as to y i am havin this problem???
connect the test point,click ready,at the same and then connect usb cable...
this job better if do 2 person,one person connect test point and 1 prson connect usb cable...
i'm quite sure i did it the way u said it... connect the test point, click ready on s1tool, connect usb... nothing happens... i was holding the pin to the test point for roughly 5 minutes waiting for something to happen but nothing...
hurmm..weird,it should search the driver after u connect usb cable...
before this,i experience this problem for the first time,realized that the step is not correct...
Delete in device manager S1 device and try all again - when windows asking for driver, not let automatically search, but manualy select from device list and brouse for driver.
Lietotajs said:
Delete in device manager S1 device and try all again - when windows asking for driver, not let automatically search, but manualy select from device list and brouse for driver.
Click to expand...
Click to collapse
That sound's like it might work but can u provide some steps as to how i might delete the s1 device in the device manager?
this win xp system.make sure phone is ON and connect usb cable.
GO control panel>system>hardware tab>device manager>
search Universal Serial Bus controllers,if i m not wrong it will list zeus flash drive if u have already install it.
if exist,uninstall the driver...reboot...
ok i change the the materials tat i used to connect the test point to the ground... i am now using a paper clip and it seem to work but now this happens...