Hi, Everyone,,New to this forum
I used the CHT9000(Taiwan), I flash OS normally, but cann't do radio successfully! anyone,who can give me advice!
I have already flashed Hard SPL v7 in my device.
my process as follow,
1.
I want to flash the radio to 1.40 version. when I run the RUUWrapper.exe, at the end process,RUUwrapper and Mobile pend at 0% ..
2,
I try to use other method...use the SD card flash the radio..but when click the powner to flash, mobile pending at 15% around.....not response!!!
My device came with:
HTC_BOOT=0108
Rom version:3.60.110.1
radio version:1.35.00.11
Protocol Version: 32.68.7020.10H
notice and add:
I updated to radio1.40, because of my Wifi, MMS, GPRS cann't connect normally, also i want to try flash radio ....
Wifi: It can search the Wlan, but it cann't connect!
MMS: It cann't send and receive MMS
G: error cann't connect, it is un-available! (Set is ok)
HHHHHHHHH,who....help ......me.........let me crazy!!!!
hi, man...who answer me ? urgent!!!
I have another quesion is :
why i failed to flash the radio , the radio1.35 isn't lost?
use the SPL-Pack's tools SSPL-HERM.exe ,i success flash the radio.
but i cann't still use GPRS, WIFI MMS ,nomally, who can help me .. i change the three OS again..but issue still exist!
Related
I try a lot of things, but, ....still no gsm
details:
first, all instalation (os, ext , radio) finished succesfull, but after reset I don't have any phone...
I try again, and the installer stop at radio (installing only the os and ext.)with message : press reset +power+directional... ant try again.... I try again but still same message apear
If anybody can help me please, reply!!!
try the other thing, the one you haven't tried.
A bit hard to help with so little detail.
Which OS,Radio original ?
Which OS version? which Radio version?
how do you mean "no GSM"? no signal? no phoneProgram?
what have you tried?
no gsm at booting
no radio, protocol and imei in device information
I make a BIG mistake, I dont make a beckup
original:; Os : 1.72, Radio version 1.16 (I think)
Now : os 2.06.00 wwe , Radio no specs.
I have the phone program , but I can't communicate to SIM (no aplication installed, if i try to run Sim toolkit),
antena icon with "!" say "No service"
when I press the phine button, the program start but with large delay.
have you double check your language and operator for nk.nbf; ms_.nbf; and radio_.nbf with xda2nbftool.exe???
Resurrect
Flash it with the launch ROM.
I just update..... don't make any verification and now i'm very sad...
[Krueger]Dr.Stein - I don't understend!
Huh?
othgor said:
I just update..... don't make any verification and now i'm very sad...
[Krueger]Dr.Stein - I don't understend!
Click to expand...
Click to collapse
What did you do?
I think he only did the upgrade with a nk.nbf and ms_.nbf.
Frpm the messages I think he means the device says it doenst have the GSM functionality operational. Typically the result of upgrading without Radio.nbf
Get a good (1.17 / 1.18) Radio.nbf (set operator!!!) & try again
i have same problem where is launch version
ok i got xda2 02 launch rom
which unable to communicate
while xda2s can upgarde my rom but error 114 no gsm
i also got launch rom but it cant communicates
I have same issue.
Please advise, I suffer problem tel. signal from radio 1.18. Then I try to R-Flash again with radio 1.12 (my friend recommended)
I do procedure as describe on page 1 (As I upgrade before) But I copy radio 1.12 instead of original (1.18 )
When I start flash , an error occur "ERROR 123 : xxxxx "
What I should do? Thanks
OK , I reply myself.
After I studied from many source, This is "contry code ID error". because I try to copy radio from other operator (others country)
so its solved lol
great you did it and by the way befoure ever trying to flash run the rom in romeditor if you dont have wrong operators rom in your pc that will never happen....i think
I can't keep a signal connection with my SX 56 on Cingular. I soft boot and I can send and receive calls but after a while I have no signal and It won't work it again until I soft boot.
I tried running the band switching tool but when I start it it just says ERROR under "current" and does noyjing else.
Starts are
ROM: A.30.09 ENG - 01/01/04
Radio Version: 6.24.00
Protocol 324e4
HELP!
TIA!
Mike
i have exactly the same problem. i have been searching google, i couldn't find any solutions.
the only thing that you can do is to turn off the phone and turn it back on, (click on the signal icon to turn it off) that case you don't need to soft boot it everytime.
if you found a better solution, please tell me.
thanks
good luck
:wink:
before updating I have same problem, but now everything is ok and it's connecting by itself
ROM: 3.04.00 ENG (WM2K3SE)
Radio: 6.25
how do we obtain a WM2K3SE version?
where did you get that OS?
thanks
if you do'nt need surfweb via gprg just ask your operator to turn it off.
that's all
I bought my 8525 off of ebay... the OS was upgraded too Windows Mobile 6 and it had the HTC Tytn 2 theme on it.. I insert my simcard and everything works well.. then some one calls me.. and the phone freezes.. now I am extremely new to the whole Windows Mobile game.. so I googled and did a hard reset on it.. after it finished restarting.. I notice that it is not reading the sim any more.. always says NO Service.. then I clicked on Start and then Phone.. nothing happened.. so I let it sit there.. tried the phone option again after half an hr or so and this time it went to the Phone option but.. it says something around the lines of can not check the status of sim emergency calls only.. If I go to network and select find network it says Cannot register on Selected Network Choose another network or disconnect your data connection and try again.. while no data connections nor Wifi is running.. Then I go to Band and if I try to Select the GSM 850/1900 and HSDPA 850/1900 it says Warning unable to change GSM/UMTS band Please try again later.. under device Info and next to IMEI I see blank space.. and try to select it says.. Then I found this site and read and read and read.. afterwards I went to Start.. Settings.. System and then Device Info.. Under there I see the following:
Rom Version: 3.30.2.1
Rom Date: 04/17/07
Radio Version: NONE
Protocol Version: NONE
ExtROM version: 2.11.255.102
So I figured maybe the radio part of the flash has gone bad.. so I downloaded the cingular update Flash.. it started and after 11% it frooze.. and came back with the ERROR: 262 then I had to do the mtty1[1].42.exe version to restore the phone back from Boot Mode.. then I tried a few other Flashes and all stick around 11%.. Then I tried just radio and they dont even go past 0%.. Can some one please help me
PS Sim is fine.. it works great with another phone.. also tried another working sim on the TYTN same issue
Herm100
IPL 1.04
Herm100
SPL 2.10.01ipro
sim manager does not respond when clicked on..
G None
R None
D 3.xx (xx= numbers)
try updating with a offical rom wm5 or wm5 and done
londere said:
try updating with a offical rom wm5 or wm5 and done
Click to expand...
Click to collapse
going to try right now.. thanks
londere said:
try updating with a offical rom wm5 or wm5 and done
Click to expand...
Click to collapse
does not seem to be working.. stuck on verifing connection with device.. even tho its synced with active sync
Maybe its not suppose to downgrade like that from 6 to Windows 5
Tried installing the latest rom flash from Cingulars 8525 support site and it freezes up after 11%.. just like stated in my post of this thread.. and gives an error 262
try this on another computer.... seems like youre having connection problems
thanks for the tip.. ill try it on a laptop right now
zammykoo said:
try this on another computer.... seems like youre having connection problems
Click to expand...
Click to collapse
same error 262.. even on the laptop after 11%
any other suggestions?
After letting the phone sit there for a few hrs.. I can now see the phone menu.. when I click on it.. it shows me the dialer and says ONLY EMERGENCY CALLS CAN BE MADE WITHOUT A PIN...
I was able to downgrade to windows mobile 5 using the guide here http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
the radio still shows as NONE and so does the protocol..
So I tried flashing just the radio and that just like always does not move past 0% and then comes back with error 262..
can some one please help me..
Maybe this will help?
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Good Luck
thanks for replying pedro2k..
spl version: 1.40.01ipro
radio= None.. (on top of SPL it says.. HERM100 IPL-1.04
Boot IN OS= Yes everything works apart from the Radio Part (device info says Radio=None, Protocol=None and IMEI= (Blank)
NO GSM= No just NONE
KITL Enabled = YES
There are some posts somewhere in the Hermes forums about radio problems like yours, have a look at all the stickies in the 4 subforums for Hermes.
thanks for the tip.. I have read quite a bit on this forum since the past few days.. Most errors are NO GSM errors.. and some NONE.. the NONE ones I have yet to see a solution for.. but I could be missing something
HI THERE,
I AM USING WM 6.0 WITH SPL 1.1. THE PROBLEM IS THE ERROR 270.
WHENEVER I TRY TO UPGRADE MY ROM TO WM6.1 OR WM6.5 OR EVEN WHEN I TRY TO UPGRADE MY RADIO TO VERSION 1.57, THE MOBILE SIMPLY GOES TO BOOTLOADER AND AFTER COMPLETING JUST 1% , IT RESTARTS AND THE PC SHOWS "ERROR 270 [UPDATE ERROR]- THE IMAGE FILE IS CORRUPTED. PLEASE CHECK YOUR UPDATE UTILITY".
I HAVE TRIED DOING HARD RESET BUT OF NO USE.
EVERYTHING ELSE (LIKE CALLS, GPRS, GPS) IS WORKING FINE. BUT I CANNOT UPGRADE THE ROM.
ANY SUGGESTION TO PREVIOUS POSTS OR NEW SOLUTIONS IS NEEDED.
ERMANO.ESTE said:
HI THERE,
I AM USING WM 6.0 WITH SPL 1.1. THE PROBLEM IS THE ERROR 270.
WHENEVER I TRY TO UPGRADE MY ROM TO WM6.1 OR WM6.5 OR EVEN WHEN I TRY TO UPGRADE MY RADIO TO VERSION 1.57, THE MOBILE SIMPLY GOES TO BOOTLOADER AND AFTER COMPLETING JUST 1% , IT RESTARTS AND THE PC SHOWS "ERROR 270 [UPDATE ERROR]- THE IMAGE FILE IS CORRUPTED. PLEASE CHECK YOUR UPDATE UTILITY".
I HAVE TRIED DOING HARD RESET BUT OF NO USE.
EVERYTHING ELSE (LIKE CALLS, GPRS, GPS) IS WORKING FINE. BUT I CANNOT UPGRADE THE ROM.
ANY SUGGESTION TO PREVIOUS POSTS OR NEW SOLUTIONS IS NEEDED.
Click to expand...
Click to collapse
Hi you need to unlock the phone
read the beginners guide in the sticky for WM6 section
Read first then flash
How to get mac address
lakeman said:
Hi you need to unlock the phone
read the beginners guide in the sticky for WM6 section
Read first then flash
Click to expand...
Click to collapse
Thanks alot lakeman for ur help.
SOLVED OUT THAT ISSUE, BUT FACED A NEW ONE.
I M STUCK AT BOOTLOADER SCREEN WHILE TRYING TO INSTALL WM6.5.
BUT I FIGURED OUT A WAY BY USING MAC AND MTTY FORMAT.
BUT I DONT KNOW HOW TO GET MY MAC ADDRESS WHILE THE ONLY THING I CAN ACCESS IS THE BOOTLOADER SCREEN?
IS IT PRINTED SOMEWHERE ON MY DEVICE OR MANUALS OR IS THERE ANY SPECIFIC COMMAND FOR THAT?