I am trying to install the HardSPL on my device (Cingular 8525). I downloaded the Hard-SPL-V7.zip file and unzipped it. I activesync and everything was fine. I waited till activesync was done.
Then, when I double click on the RUUWrapper.exe file, it says
The application failed to initialize properly (0xc0000135). Click on OK to terminate the application.
Any suggestions on what I could be doing wrong. This happens on all the computer that I tried.
ftarules said:
I am trying to install the HardSPL on my device (Cingular 8525). I downloaded the Hard-SPL-V7.zip file and unzipped it. I activesync and everything was fine. I waited till activesync was done.
Then, when I double click on the RUUWrapper.exe file, it says
The application failed to initialize properly (0xc0000135). Click on OK to terminate the application.
Any suggestions on what I could be doing wrong. This happens on all the computer that I tried.
Click to expand...
Click to collapse
Check out www.mrvanx.org
Might you be using Vista???
What version of VBScript is on your machine???
Why am I using three question marks???
do u have microsoft .net framework installed?
ftarules said:
The application failed to initialize properly (0xc0000135). Click on OK to terminate the application.
Click to expand...
Click to collapse
A very similar problem has driven me crazy for weeks when I started messing with the Hermes. In my case, there were several versions of the RUU that would bomb if run from a network drive.
Copy them to the desktop and see if it works. Hope it helps
Solution
Code:
http://www.microsoft.com/downloads/details.aspx?familyid=0856eacb-4362-4b0d-8edd-aab15c5e04f5&displaylang=en
ftarules said:
I am trying to install the HardSPL on my device (Cingular 8525). I downloaded the Hard-SPL-V7.zip file and unzipped it. I activesync and everything was fine. I waited till activesync was done.
Then, when I double click on the RUUWrapper.exe file, it says
The application failed to initialize properly (0xc0000135). Click on OK to terminate the application.
Any suggestions on what I could be doing wrong. This happens on all the computer that I tried.
Click to expand...
Click to collapse
If you search for that error code on Google most of the replies point you to meeding .net framework.
I found this out after clearing out my laptop and not being able to flash Roms which worked before - reinstalling .net cured the problem
Related
I get the following errors when cradling my device:
"Failed to Set Up Partnership
An system error has prevented Microsoft ActiveSync from setting up a partnership between your mobile device and this computer.
To set up a partnership, disconnect your device, restart Windows on this computer, and then reconnect your device."
I've done everything like reinstalling and stuff but I still get this error. Anybody encounter anything like this? Before this happend, the unit was happy syncing w/ my pc.
Thanks.
i would try to delete the partnership
Thanks for replying. Tried everything already, short of hard resetting. Had no choice but to hard reset. Now everythings ok. But I still can't figure out why it refused to setup a partnership.
activesync version
activeSync version?
3.8
try reinstall
reinstall the activesync version 3.8...
download here: http://forum.xda-developers.com/download.php?id=3293
thread: http://forum.xda-developers.com/viewtopic.php?p=97169#97169
how to uninstall:, microsoft: http://support.microsoft.com/default.aspx?scid=kb;en-us;263152
Thanks Jo for the links. Got it working already. Reinstalled the whole damn thing. Anyway, been using some of your cab files from your extrom. Great job. I'm currently using a baseROM from Sin. Don't know if this baseROM is identical w/ that of Dr. Stein's. Sin hasn't answered my pm yet.
U
you are welcome bai...
Been trying everything on the Internet and managed to make some headway with Monet (Virgin Lobster 700tv) unlock (this might work for Meteor/C700 as well).
1. Firstly you need to get rid of the 'registry security policy' lock.
Download cert install sp.zip:
[see attachment]
a. copy "SP_AllowCertificateInstall.cab" to the root of Monet memory or card
b. Use file explorer on monet to navigate to file. Click to run. Should run ok.
c. Unzip "SDA_ApplicationUnlock.zip" on PC and run "SDA_ApplicationUnlock.exe" whilst Monet is connected via activesync
2. Copy registry editor onto Monet. I used PHM, but others should work. Note install PHM loader on PC whilst monet is connected via activesync. It might install correctly on Monet, it might not. This does not matter. Just navigate on your PC to Program Files\phm and find the .exe file and copy to root of Monet memory or card.
Also nice free remote registry editor here (works from PC whilst phone is connected via activesync):
http://www.breaksoft.com/Blog/Utilities/2005/1/Mobile_Registry_Editor.aspx
Excellent 'free' combined file explorer and registry editor (perhaps for later - after app. unlock) SGS:
http://www.handango.com/PlatformPro...925777&Ntt=registry&productId=195244&R=195244
3. Using phm (or the registry app you like) change the four keys specified in this guide (you might find the above process has already reset 1001 and 101b:
http://wiki.spv-developers.com/HTC_Application_Unlock_Guide
They are:
Under HKEY_LOCAL_MACHINE\Security\Policies\Policies:
a. Change the DWORD named "1001" to 1 (could originally be 2)
b. Change the DWORD named "1005" to 40 (could originally be 16)
c. HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1017 = 128 or 16 (before) 144 (after)
d. HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 101b = 1 (this key might not exist, if so, create it).
4. Restart
5. HOORAY. Now your phone is fully application unlocked.
-----the following procedure is to SIM Unlock, this currently does not work. Possibly spv-services will be updated at some time to work with the Monet---->
6. Now download spv_services:
http://www.spv-developers.com/forum/showthread.php?t=236
a. copy the cert.cab file to you Monet. Select and run using File explorer. it should run fine.
b. Next step. Run SPV_services from PC whilst phone still connected via Activesync. Should unlock ..... however I get checksum error....
Will investigate. Anyone have any luck please say. At least we can now get the phone app.unlocked.
------------------------->
Note: I have read that the phone might again become app.locked if you do a hard reset. If this is the case, just follow the above again.
rgds
colonel said:
(...)
b. Next step. Run SPV_services from PC whilst phone still connected via Activesync. Should unlock ..... however I get checksum error....
(...)
Click to expand...
Click to collapse
So this thread should not be named Full unlock for HTC Monet :>
apparently wen i tell spv services to use simlock tool. it freezes at a blue screen trying to load a php.. this is after i input AGREE into the box..
it opens fine b4 that.. am i doing anything wrong?
bongmaster said:
apparently wen i tell spv services to use simlock tool. it freezes at a blue screen trying to load a php.. this is after i input AGREE into the box..
it opens fine b4 that.. am i doing anything wrong?
Click to expand...
Click to collapse
SPV-Services needs to access the internet.
A php is an active type of web page.
It would appear that there is something blocking it from access the internet. Most probably a firewall on your PC, either the internal windows one, or a 3rd party package you have installed. You need to check this.
If its for the Monet I wouldn't bother anyhow as SPV-Services can not currently SIMunlock this phone.
rgds
colonel said:
SPV-Services needs to access the internet.
A php is an active type of web page.
It would appear that there is something blocking it from access the internet. Most probably a firewall on your PC, either the internal windows one, or a 3rd party package you have installed. You need to check this.
If its for the Monet I wouldn't bother anyhow as SPV-Services can not currently SIMunlock this phone.
rgds
Click to expand...
Click to collapse
1st thing i checked was the firewall..
i know wat a php is i run a phpbb forum and yea it is a Monet (lobster 700)..
shame ( i really need to unlock the networks on it ) i have an O2 sim and wen i put it in it askes for a network unlock code.. if only i had that code.. any idea how to obtain it?
the only way currently is to use virgin or a commercial service
If you put at least £30 of talk time on your virgin account, they will send you the unlock code for free.
Otherwise search google or this forum for a commercial unlocking service.
rgds
colonel said:
1. Firstly you need to get rid of the 'registry security policy' lock.
Download cert install sp.zip:
http://www.spv-developers.com/forum/showthread.php?t=425
Click to expand...
Click to collapse
Hi, I have a question. I would like to try it but the link above shows: Invalid Thread specified. If you followed a valid link, please notify the administrator :-(
burticek said:
Hi, I have a question. I would like to try it but the link above shows: Invalid Thread specified. If you followed a valid link, please notify the administrator :-(
Click to expand...
Click to collapse
Edit: Never mind. I have found it ;-)
Virgin Lobster
I have followed all the instructions
I get an error when running the sim lock to as follows:
Encrypted checksum not found
I then use a vodafone sime and get Network is locked. PLease input unlock code.
Any ideas?
SteveW
classicxda said:
I have followed all the instructions
I get an error when running the sim lock to as follows:
Encrypted checksum not found
I then use a vodafone sime and get Network is locked. PLease input unlock code.
Any ideas?
SteveW
Click to expand...
Click to collapse
simunlock is not working yet on the monet.
this procedure only app. unlocks
rgds
c.
Lobster unlock
What would it cost to do this?
Cheers
SteveW
just phone virgin if yu have a lobster. they require £30 of airtime to be purchased before they give you the code
Application Unlock for HTC Monet
Hi colonel
I have been trying in vain to do an application unlock on my Lobster 700tv. I have managed to install and run the "SP_AllowCertificateInstall.cab" which went ok. The "SDA_ApplicationUnlock.exe" also ran ok. However, running PHM required a copy to be placed on the Monet which I did. Attempting to run the "setup.exe", gave the following message:
"ALERT: Setup is Not a Valid Windows CE Application"
Because of this, I attempted to change the registry keys using "Mobile Registry Editor.exe" which seemed to do the job. However, applications still wont work (I'm trying to install TomTom Navigator 6).
I have since managed to load and run "MobileRegistryEditor.exe" on my phone without problems but I still cannot get TomTom Navigator 6 to run, although it loads onto the storage card ok.
Please can you help?
Regards,
leadweight
leadweight said:
Hi colonel
I have been trying in vain to do an application unlock on my Lobster 700tv. I have managed to install and run the "SP_AllowCertificateInstall.cab" which went ok. The "SDA_ApplicationUnlock.exe" also ran ok. However, running PHM required a copy to be placed on the Monet which I did. Attempting to run the "setup.exe", gave the following message:
"ALERT: Setup is Not a Valid Windows CE Application"
Because of this, I attempted to change the registry keys using "Mobile Registry Editor.exe" which seemed to do the job. However, applications still wont work (I'm trying to install TomTom Navigator 6).
I have since managed to load and run "MobileRegistryEditor.exe" on my phone without problems but I still cannot get TomTom Navigator 6 to run, although it loads onto the storage card ok.
Please can you help?
Regards,
leadweight
Click to expand...
Click to collapse
I also have been trying to unlock my Lobby to no avail.
Used a couple of reg editors but when u change the values the phone comes back "Unable to perform this operation".
I also used the HTC unlocker which came back with the same message.
Lobster headache
Hi bocsta
I had problems to start with but I had failed to read colonel's instructions correctly. I couldn't get PHM to run on my phone so I tried some of colonel's other suggestions. I found that "SGS Explorer" did load ok and I used its registry editor to change the registry keys as listed. I am assuming that my phone is now unlocked but TomTom Navigator 6 will not run.
Can someone please help before I throw my lobster back in the sea?
Regads .....
leadweight said:
Hi bocsta
I had problems to start with but I had failed to read colonel's instructions correctly. I couldn't get PHM to run on my phone so I tried some of colonel's other suggestions. I found that "SGS Explorer" did load ok and I used its registry editor to change the registry keys as listed. I am assuming that my phone is now unlocked but TomTom Navigator 6 will not run.
Can someone please help before I throw my lobster back in the sea?
Regads .....
Click to expand...
Click to collapse
Colonels zip file comes nack as not a valid archive ?
Where can I find the first file in his list being : SP_AllowCertificateInstall.cab ???
Find File
bocsta said:
Colonels zip file comes nack as not a valid archive ?
Where can I find the first file in his list being : SP_AllowCertificateInstall.cab ???
Click to expand...
Click to collapse
The file you require is "cert install sp.zip"
You can get it by clicking on colonels attached files link on the bottom left of his list.
Regards
leadweight said:
The file you require is "cert install sp.zip"
You can get it by clicking on colonels attached files link on the bottom left of his list.
Regards
Click to expand...
Click to collapse
Have you tried downloading it recently The zip file says it is not a valid archive or is damaged ?
bocsta said:
Have you tried downloading it recently The zip file says it is not a valid archive or is damaged ?
Click to expand...
Click to collapse
I have just tried it again and it downloaded ok. I'm not sure why you have had problems - keep trying as it could be just a glitch.
Regards ...
leadweight said:
I have just tried it again and it downloaded ok. I'm not sure why you have had problems - keep trying as it could be just a glitch.
Regards ...
Click to expand...
Click to collapse
Yes it dowmloads OK. I just cant unzip it. Can you try to unzip it please ?
If it fails and you still have the Zip file that you unzipped originally cann you please PM it to me ?
Thanks
I have tried to run DCD's latest kitchen on multiple computers and every time I run BuildNB, it crashes when it tries to start BuildOS.
I have tried it on WinXp Sp2, WinXp Sp3, a bare install of Winxp SP2. I have tried it on all versions of Dot Net....
Still no love for me!!! :-(
WTF am I doing wrong???
EDIT:
Ok the issue was a path problem, apparently there was an issue where if I tried to run it from My Documents folder or the Desktop folder that the path was too long.
I moved the kitchen folder to the root of C:\ and it ran perfectly.
Hope this helps others that have the same issue!
Thanks everyone for your help in figuring out the issue.
2K3GTP said:
I have tried to run DCD's latest kitchen on multiple computers and every time I run BuildNB, it crashes when it tries to start BuildOS.
I have tried it on WinXp Sp2, WinXp Sp3, a bare install of Winxp SP2. I have tried it on all versions of Dot Net....
Still no love for me!!! :-(
WTF am I doing wrong???
Click to expand...
Click to collapse
Have you installed Visual C++ 2008 Runtime?
http://www.microsoft.com/downloads/...34-3e03-4391-8a4d-074b9f2bc1bf&displaylang=en
It is required along with .net version greater than 2.0
Yes, I have installed it even though it is no longer required for DCD's latest kitchens, but BuildOS still crashes...
Sorry, that's all I've got. Hopefully someone else can chime in.
2K3GTP said:
Yes, I have installed it even though it is no longer required for DCD's latest kitchens, but BuildOS still crashes...
Click to expand...
Click to collapse
Is it crashing immediately.....have you run it before?
It worked when I cooked a DCD ROM a few months ago, now with the new kitchen it starts to move the modules then BuildNB calls BuildOS and it crashes immediately. I can click on BuildOS.exe and get the same result.
You're extracting the folder from the rar file and not just running BuildNB.bat from the archive correct?
Yes, that is correct. I am also an admin on these PC's and I am running it of a network drive but if I copy it locally it also fails so that is not an issue.
This is making me nuts.
2K3GTP said:
It worked when I cooked a DCD ROM a few months ago, now with the new kitchen it starts to move the modules then BuildNB calls BuildOS and it crashes immediately. I can click on BuildOS.exe and get the same result.
Click to expand...
Click to collapse
Have you downloaded it again? Sounds like a corrupted download......
This is what the debugger says:
An unhandled exception of type 'System.IO.DirectoryNotFoundException' occurred in mscorlib.dll
Additional information: Could not find a part of the path 'C:\Documents and Settings\user\Desktop\dcd_titan_kitchen_3.2.6\dcd_titan_kitchen_3.2.6\TOOLS\SYS
Did you re-download the kitchen again??
path too long?
try to extract the archive to a folder on the root of C:, like "DCD326" and run it from there. there may be a limit to the length the path to a file can be. good luck...
When i go to open any type of flashing program as in Custom_RUU.exe or Raphaelwrapper.exe i get this error "The application failed to initialize properly (0xc0000135). Click ok to terminate this application." i have flashed multiple times before but never on this computer. I am running windows xp pro. Please and thank you.
Maveaxe said:
When i go to open any type of flashing program as in Custom_RUU.exe or Raphaelwrapper.exe i get this error "The application failed to initialize properly (0xc0000135). Click ok to terminate this application." i have flashed multiple times before but never on this computer. I am running windows xp pro. Please and thank you.
Click to expand...
Click to collapse
I believe NetCF is required for the flashing programs. Do you have that installed on that computer?
If all else fails, you can always flash via SD card, per the sticky guide to flashing...
Thanks for the help. it wasnt Netcf but close it was Microsoft .NET Framework 3.0. that is needed for flashing programs to run.
Maveaxe said:
Thanks for the help. it wasnt Netcf but close it was Microsoft .NET Framework 3.0. that is needed for flashing programs to run.
Click to expand...
Click to collapse
That's actually what I meant. Obviously, you wouldn't want the compact framework (CF) on your PC... I was a little sleepy last night...
Hopefully, I pointed you in the right direction at least...
Please please help
I have read lots of threads and have downloaded the radio i need (2.07.50.27) to run the rom i need (sense 2.5 cookie). It says to Rename the extracted file to "RUU_Signed.nbh" (already is named that when extracted) and flash with the CustomRUU.
When I try to run CustomRUU through the handset it says it is not a pocketPC application. When I try to run it through the computer, nothing happens.
What am I doing wrong?
Thanks in hoping
baileyjacks said:
Please please help
I have read lots of threads and have downloaded the radio i need (2.07.50.27) to run the rom i need (sense 2.5 cookie). It says to Rename the extracted file to "RUU_Signed.nbh" (already is named that when extracted) and flash with the CustomRUU.
When I try to run CustomRUU through the handset it says it is not a pocketPC application. When I try to run it through the computer, nothing happens.
What am I doing wrong?
Thanks in hoping
Click to expand...
Click to collapse
Hello mate!
First of all: You have HSPL instaled on your device?? If the answer is YES, you could continue.
The CustomRUU.exe is a app for PC, so you need to run it on a PC not on your HD2, OK?!
So, to it work the way it is designed to work, you need to run it as admin (right click on the CustomRUU.exe and select RUN AS ADMIN...).
In case it does not work, you could flash the radio via SDcard (rename the NBH file to LEOIMG.nbh and put it on your SDcard. Enter in the bootloader and it will tell you what to do.)
Read here for more usefull info about flashing your LEO: http://forum.xda-developers.com/showthread.php?t=609477
Keep reading dude!
Hope it helps!
if customruu does absolutely nothing when you try to run it, chances are your anti virus program has disabled it. You need to turn off your av, and then download it again. (just turning off av is not enough, because it has already disabled customruu as soon as you downloaded it.)
I have the same issue.
HSPL is installed on the phone,
active sync is on,
and I have renamed the radio file and put it in same folder as the customruu.exe
I am running it as the administrator (no antivirus on the computer)
Nothing happens when I double click.
I have tried changing radio files, but still no luck.
I have downloaded customruu from 2 different sources to make sure its not corrupt.
Any ideas?
Viktorca said:
I have the same issue.
HSPL is installed on the phone,
active sync is on,
and I have renamed the radio file and put it in same folder as the customruu.exe
I am running it as the administrator (no antivirus on the computer)
Nothing happens when I double click.
I have tried changing radio files, but still no luck.
I have downloaded customruu from 2 different sources to make sure its not corrupt.
Any ideas?
Click to expand...
Click to collapse
firstly, no need to rename the nbh file.
second, was there av running when you downloaded it? some av programs disable it as it arrives.
thirdly, you are right clicking and choosing run as administrator? cos just being logged on as administratior isn't the same. (though its less important for customruu than for hspl)
what operating system?
Hi samsamuel,
Thanks for the help.
I dont have a virus scan at all.
Laptop is running windows xp, there is only one account and it has administrator rights.
I have right clicked > Run As > Following User - there are 2 options, administrator or vik.
Admin account has not been set up, but I had a go at selecting it anyway (no luck),
also no luck with my main account "vik"
in that case only. suggestion i have is use sd card to flash, or try a different comp. sorry.
thanks mate, I have tried it on another computer and it has worked fine.
Updated the radio and now using andriod. cheers for the help