Related
After i upgraded to this radio i have had interesting problems with my phone. ithought it was bricked and it very well could be. But sometimes it decides it wants to work but after a minute or two it cuts off. when a softreset or hard reset are perfromed i get nothing but a white screen. I can tell it goes thru the whole process bekuzz usually after putting it to sleep a few times i get my regular screen but the radio doesnt seem to be connected. any help would be appreciated. also the buttons on the face of the phone dont seem to work.Thanx
What is "Regular Screen"?
Regular screen means the screen u would normally get after your boot and splash screen. Or better said my today screen. Sometimes i cant get my today screen up. i had BL 1.04 before the upgrade if that matters any
Today screen is very good! your device isn't fully bricked. It may be a bad radio flash or it may be a hardware issue that merely coincided with your radio upgrade. Next time you get a today screen, try to flash one of the other sspl based radio only updates (find in wiki under radio only upgrades). Remember to practice safe flashing techniques!
usb on rear usb port. No usb hubs!
all winapps closed
running winXP Pro
activesync connected
screensaver/sleep mode off (flashing takes 20+ minutes)
i have flashed the 1.27 radio again without having my today screen and that did nothing. It went thru the whole process of flashing and everything but same results, just a white screen when booting up and afterwards. im downloading the 1.34 radio now.
You need to flash the sspl version which requires first being on the Today Screen (not white screen). Tri-color boot screen will show v1.09-Des if you do this.
i guess i will have to wait to see if i get another today screen and hope that it doesnt reset itself
does it matter that i can put my phone to sleep and wake it up over and over, i just keep getting the white screen. bekuzz now i cant seem to get my today screen back anymore
ok i have done what u said and flashed the 1.34 radio and still have the same problem. after the flash i had my today screen for a minute then it reset itself and now is gone and back to the white screen. also when i was on the today screen i didnt have control of the buttons only touch screen.
i think i may have a different problem. it doesnt seem to be resetting itself everytime it goes blank but that the screen is dying on me. hmmmmmm....... this is quite strange. i can also recieve calls. i cant answer them but the handset rings.
This may be silly but if I were in your place I'd just reflash everything with an official rom that replaces everything (i.e. SA 1.35) and see if that fixes the problem (though i might wait until somebody who knows more then me verifies this is a good thing to try). I'm wondering if the bad flash somehow effected something in your OS or something.
When I mess something up like this, I like to get back to a place which has been known to work - then I have a better idea of where I am (ie brick or bad flash)
Hope this helps
yea i actually went back to the original cingular ROM that came with the phone. so we shall see what happens from here. i also will have Cingular send me a new phone, i was tired of the scratches anyway. So far they havent noticed that my phones are supercid yet. Keeping my fingers crossed
Hardware problem IMHO...
Sleuth u are right. No matter what i do to the phone it yields the same result. My screen still turns off and the buttons dont work. iwonder what couldve caused this. i didnt drop it. well not recently anyway. BTW.... is there anyway to get the original 1.16 radio back on there. i tried doing it but it just hangs at 0%.
Thanks Sleuth for all your help, you are definetly one of the reasons this forum is helpful. That and that good ole WIKI.
has anyone come across the problem that when you move to say 3g from gsm or back or you loose signal as your in a bad signal area and then get it back, the phone actually looses the radio says "operation failed" and relocks on to the signal?
mine will sometimes loose the signal need restarting and on the boot screen will show NOGSM when its clearly installed as it worked 20seconds ago. i have tried many types of radio rangeing from 1.07 to 1.41 and all their varients. i am at a loss why my phone just looses it and then forgets it has actually lost it untill i try to make a call or send an sms. no calls or sms's can be received by me whilst the phones done this and it does it a hell of a lot.
sometimes it also just looses the radio half way through a call or data call.
anyone got any ideas?
i have a m3100
IPL 1.04
bootloader 2.10oli
and the XDA live OS installed. however it does it on any OS i have tried so far. and thats alot of them.
Same for me.
Same problem for me.
Often I get the message "operation failed" or "the phone is not ready, wait 15 seconds and try again". Thought it was a problem with the new 1.38 radio, but it seems to be something different.
i also get all those error msg's. i have no idea how to fix it either and no 1 here seems to have a clue either :-(
i Had the same problem with mine it due to hardware i guess. Your phone might have fell down or something then this kind of problem starts I fixed mine by opening my phone up and fixed the arial part properly
torrentulla
is there a guide you follow for that or can you give me any tips to do it myself?
thanks
Smith2001 said:
torrentulla
is there a guide you follow for that or can you give me any tips to do it myself?
thanks
Click to expand...
Click to collapse
I fixed my phone almost the same way as Torrentulla did. I'm my case it seems that something was damaged when I dropped my phone a few weeks back. I discovered that when I pushed at a spot right below the flashlight that the radio kept coming up all the time.
These are the steps I took to repair:
Remove all 4 screws (very small torx) at the back of your hermes
Remove back
Put a little piece of paper on the "pressure" spot
Put your phone back together
Turn it on and enjoy!
I hope you'll manage to fix yours aswell!
Phone sometimes shows No GSM, fails to ring
Hey guys, I posted this in the dead hermes thread, but decided to post it here as it's not really bricked. I think it may be a faulty component or something.
My phone was working fine this morning, then in the afternoon I noticed I would have to try to make a call 3 or 4 times before it would go through, it kept on giving me the error (Can't connect, or something along those lines).
Then, I checked my voicemail and found that I had 10 messages from people who had been trying to get in touch with me, but my phone hadn't been ringing.
The kicker came when I soft reset my phone and all of a sudden No GSM popped up! I soft reset it again, and it was gone, and worked fine for a couple of hours. Now its back to not ringing again.
I flashed radio 1.41.00.10 about a week ago, and have been running fine with no problems since. I haven't flashed any rom's in the past week, and this problem just started yesterday. No new software has been installed (except Pimp my black v0.1).
I don't know a lot about the radio, but I didn't think it could become corrupted during regular use, I thought you could only mess it up when you were flashing the phone. I wonder if there is something wrong with the radio? Could the hardware be faulty? This phone is about 8 months old and hasn't had any problems up to this date.
I'm going to flash radio 1.40.10.0 again and see if that makes a difference, but I'd like to know if anyone has any ideas as to what could be causing this.
Sorry this post was so long,
Thanks
-Kai
it seems i don't have a pressure point on mine as the radio is working as and when it likes. which is not alot
gotta sort it out somehow, will take it apart and see if theres anything obvious.
I have the same problem too, phone sometimes shows NO GSM on startup and sometimes it works. Here's where I posted : http://forum.xda-developers.com/showthread.php?t=306073
Now its not even showing NO GSM it just says: NONE, NONE
Also, I noticed that it will only last about 6 hours on a full charge before the battery is absolutely dead.
I'm beginning to think that it may be my radio 1.41.00.10
It seems strange that all of these people are suddenly having this problem now.
Whats the warranty like on these devices? Is it a 1 years parts and defects warranty? Or is it some ****ty 90 day warranty?
As it is my phone is a piece of garbage, not worth using at all, I am very disapointed in it.
It's a hardware problem.
Hi guys,
I'm experiencing the same problems since two months and I've been struggling with all kind of OS, ROM, RADIO and bootloader, without even gettin close to solve them.
My phone randomly loads the RADIO (otherwise I get the "No Gsm" message), even when loaded, the connection is not suitable and my phone is often unreachable on the net. The battery life is very short because the phone always looses the signal and then seraches till he find it, before loosing it again.
So I disassembled my phone and did a lot of testing with hardware connections. I have found that the motherboard connection with the flash/scroll module isn't stable at all. You can easily move it and find that this affects the phone ability to load the RADIO. It seem strange but it's true. I can't solve the problem and I'm very upset with HTC because of their hardware components lack of quality. I would like to try to change the module to but I can't find a place where i can buy HTC hardware parts.
So I'm going to change my pda, I'll never buy HTC anymore.
Any help?
Has anyone figured out the problem? If it is hardware, what "pressure" spot is it? I tried, but wondered if I'm not in the right place.
In my case it was a spot right below the flash/scroll-part. As said earlier, i put a piece of paper on the spot and reassembled the phone. It still works excellent after a week!
My dopod can't connect to the mobile network as well, but only with the 3 network. It seems fine when being connected to an Optus network. Have you guys tried using a different network simcard?
I'm not sure if mine is a physical problem but maybe a setting which i need to configure so i can connect to a 3 network. Help anyone?
ROM version : Pro BLACK 3.0
ROM date : 01/04/07
Radio version : 1.41.00.10
mine also works just under the flash with the cover off, but if i hold it too hard then the screen goes all white and doesn't work, until i can get the case off its a hit and miss game at the moment.
thanks very much for the tips and help
Dan
Larrys said:
.....
So I'm going to change my pda, I'll never buy HTC anymore.
Click to expand...
Click to collapse
I cannot agree with this more.
I am sick to death of this phone. I had one of the first in the country for normal sales and spent weeks arguing with HTC who flatly denied the screen alignment issue. EVENTUALLY I got them to fix this after referencing posts in this forum.
I continued to suffer the "coma" software issue - why is it so F*((&&^ dificult for a device to wake up when its auto-sleeped?
And finaly, to top it off, I have been suffering this problem. I cannot express how mad I am. Did I buy a cheap phone? NO. I have had nothing but problems with this phone and will NOT buy another HTC.
Oh and if anyone knows how to repair a failed Radio upgrade, please help me! I don't have any choice but to use it until the IMate Ultimates come out.
Due to seeing this radio problem I thought I would try downgrading the radio from 1.4.summint or other (the latest) to a slightly older version. This was of course before I saw this thread. During the downgrade the installer stopped at 15%. Now no matter what I do it sits at the IPL/SPL screen (3 colour bars+white). I have done the obvious i.e. follow the installers error procedure (remove the battery).
Device: HERM200
IPL-1.04
SPL-2.10.Olipro
Please help me be able to use this for another month or two at most - i hope!
Thanks guys
update:
OK Guys
thanks to this thread: http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
I now have it trying to boot the o/s. I get the message "No GSM" on the boot screen but when it boots up it asks me for my pin number and freezes. I guess its locking up because it has no "phone" part? According to the instructions in the other thread I am supposed to flash it again but I can't as the phone locks on boot.....
Any ideas?
*FINALY* got it back into pre-flash feck up situation. Sadly, this still leaves me with the hardware problem. HTC can go poke themselves until the cows come home. Im taking my money somewhere else.
i installed the XDA Windows mobile 6 about 3-4 months ago on my SPV M3100,
everything worked fine untill just lately it started displaying just a plain white screen, not bricked because if i rapped on the power button a few times it would display everything normally?
problem is it has started doing it more and more often untill lately it decided to completely go white - i found out the phone still works just a blank screen? also some of the mounted buttons stopped working at times and would work othertimes?
ive fully charged it, turned it on and plugged it into my pc but im not sure what to do?
is it something to do with XDA, maybe some kind of virus or should i literally re-install the orange windows mobile 5 and send it back?
any help would be great! - im in a bit of a pickle here
thanks -Edd
wm6 spv m3100 white screen
hi there
if anyone is following this thread, i too upgraded first to 4.01 as good as gold, then to 4.30, Schaps ROM's. all fine but then the white screens started in 4.3, in the end about 10-14 days i had to remove the battery to boot the unit, and only thrn with PSU/USB plugged in, so power issue?
anyway i pushed thorugh to 4.31 alls currently well, keep you posted
cheers in all others senses great work all round
cheers pete
Yep, I've got this issue with my HTC Hermes but it only manifested itself after the upgrade to WM6?!
Can you ALL please tell us what bootloader you are running?
I followed the online instructions for getting Schaps WM6 ROM on board for my SPV. I shall dig them out.
mrvanx said:
Can you ALL please tell us what bootloader you are running?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=352857
Hi Folks
My Hermes/Tytn is an Orange M3100. Recently it has begun dropping calls, or rather, ignoring them. The caller could hear a ringing tone but the phone wouldn't switch on, show me an incomming call or anything. A short while later, usually after I'd switched it on (I mean, the screen, "off" is that it's on standby) I'd get the notification of a missed call. More often than not it would come through after I had made a call.
This reached a "point" on the weekend where I missed about 17 calls from the Agency to get work for me as I was the only one available
So. I upgraded as reccomended on here. Up to HardSPL 2.10, Radio version 1.41 and then upgraded to Schaps 4.22 WM6 Rom.
Now, I made sure that ActiveSync has connected and synchronised, and all my contacts and PIM info is in Outlook. However, A/S won't transmit the information to the PDA, even though it tells me it's synchronising.
The only way I have managed to get my PIM data/address book back onto the PDA was by running a custom SPB backup file to restore the calender, sms and phonebook.
This is where the fun starts. My PIM and Tasks then go "read only" merely by having a warning telling me I have no memory and to go and close other programs down. But there isn't anything else running!
Fine. Right. Ok. Obviously I've done something wrong. I did a hard reset this evening. It wiped all the data internally and reset it. I changed the details to match the username that was already stored in A/S and plugged it in.
It tells me "Connecting" and the green thing swirls around but doesn't actually do anything.
I have heard mention of the MTTY software, so I've got that here. But it won't allow me to connect on USB, only Com1, 2 or 3.
So I've a pretty useless phone at the moment. It's got none of my files on there, the satnav is rendered useless merely because I can't install the sod and all the other problems to go with it.
Short of screaming abuse at it and throwing it across the room I'm a bit stuffed. And I can't spend anymore time on it as I've got to be getting up for work at 4am (only finished tonight at 8pm ) for another full day
I've read the wiki, I've gone through the pages and pages and, er, pages of posts but I'm hitting a brick wall somewhere. I'm not as bright as you guys, but I get by.
TIA. Elwyn
Click to expand...
Click to collapse
The device is no longer worthwhile for me and have spoken to Mike Channon over it. If you can change that or help me change it I would be grateful
Mikechannon is the main man when it comes to the hardware side of things, if it was an early bootloader issue (related to bad NAND blocks) then thats what i was questioning your SPL version about.
If mike is confident it is the hardware problem then id take his word for it, the guy rocks
/me has to get his mikechannon ass kissing back into shape again hehe.
mrvanx said:
Mikechannon is the main man when it comes to the hardware side of things, if it was an early bootloader issue (related to bad NAND blocks) then thats what i was questioning your SPL version about.
If mike is confident it is the hardware problem then id take his word for it, the guy rocks
/me has to get his mikechannon ass kissing back into shape again hehe.
Click to expand...
Click to collapse
Not entirely sure what it is yet. If WM6 wrote to the 'wrong' part of the memory, would reflashing back to WM5 fix this?! Is there a way of repairing NAND issues?
MrVanx, I looked in the original thread that I posted in about this issue and followed you're link. Not sure whether I did or didn't at the time, but I can see there are instructions for downgrading the ROM from 6 to 5. However I am now in the situation that I can't use the USB cable as it causes it to white screen, but probably could if I did it via memory card....
white screen continued
hi there
sorry about lack of info i installed olipro 1.4 as per the instructions at the wiki i think. mine doesnt boot white, it turns white/fades to white when in use, or more commoinly i will press off after use, then later turn the unit on, and it will come white. first few times it si normal after 2nd on/off, then it stops completly requiring a hard boot, then that stops and it requires a battery off, then that stops. however it always seems to repsond when power connected, even if 100% charged or just off.
it feels to me like a power issue, still there in 4.31, wasnt there in 4.01, going back now to see if its hardware.
i will give as much info as you guys need, i got my phone from orange in may 2007
pete
white screen update
hello again
still on 4.31 activesync isnt playing at teh moment but anyway.
on the screen thing, if i leave the unit standby itself and then power back on it seems fine, so far 3 hours of good, no white screens.
thanks pete
hi there i face this problem with my imate jasjam sorry to tell you that but this problem is a hardware problem you be confirm that it hardware by push by your 2 fingers below the screen and above the keys like you catch"hold" something bush the power key again the white screen will be disappear .sorry if you don't understand me because of my English.
Hi everybody.
Anybody solved problem with white screen?
I have the same truble as EddTQ - White blank screen & also some of the mounted buttons stopped working rarely 2 week before white blank.
same problem here.
Maybe a radio problem?
Folks,
The problem you are describing sounds like the flex connector.
http://forum.xda-developers.com/showthread.php?t=321163&highlight=white+screen
This thread should give you some details. I had the same problem but phoned Orange who sent me out a new one in 9 hours!
exactly
What happes is exactly the problem explained by alkizmo ...
thanks.
My touch screen will not work at all, everything else on the phone works just fine. I tried a hard reset and now I am stuck at the alignment screen. Any suggestions.. Anyone run across this error?
Thanks
reflash bro
put the stock rom back on
and then put the modded rom on
and it should be fine
Typically means something is interfering with the recognizer.
If you are using a protective case (shell) or screen protector, try removing them temporarily to see if they may be causing your problem.
I didn't have anything over the screen.. Any idea why it would do something like that?? I'm going to reflash to stock and back to modded ROM tonight and I'll let you guys know in the morning.. Thanks for your help.
Could be a "bad" flash.
If it still happens with the stock ROM flash, you may have a defective unit on your hands.
Hardware problem?
I had the exact same problem about a week ago. I tried reflashing the device, hard reset, etc. In the end, I couldn't even get past the screen calibration wizard. My conclusion was that I had some kind of harware problem -- the touch screen would respond intermittently for brief periods of time and then go unresponsive again.
My fix: I took the phone to my ATT service center who, much to my gleeful surprise, gave me a new one (warranty exchange) without any hassle. I expected to have to fight with them, but the transaction was trivial and stress-free.
I'm now deciding which WM 6.5 ROM I like the best. Many thanks to all the hard-working contributors and chefs on XDA for providing such awesome content and support!
Good Luck with your phone
i also had this problem recently. phone was working fine in the night, went to bed and woke up and was unresponsive. Tried everything. I ended up flashing back to all the stock stuff and sent it in for repairs. I got the screen and dpad replaced under warranty. I have no idea what caused it, but it happened. Definately not a software issue if you have reflashed...
my advise, flash back to stock spl and your carrier rom and send it back.
I had a similar problem and opened a thread as well. My problem in chronological order
1. Bought a TMobile MDA IV over ebay.
2. Flashed several different ROMs of WM6.1 and was just enjoying myself.
3. Installed a 6.5 ROM the calibration screen required me to go through 3 full circles.
4. Worked fine for a day, then the device was locked and watever I tried I just couldnt get to open it up
5. Did softreset, it didnt help either. I Would end up at lock screen
6. Finally got back to HTC stock ROM 6.1, and I couldnt get past the calibration screen for a month.
7. My conclusion as well, that its a hardware problem, unfortunatel where I live I dont have Tmobile and the screen from touch pro is slightly different in size to the tmobile variant.
8. Hence it was a brick!!!!
9. After a month just last week, I thought of trying to flash back to 6.5 and see if it works.
10. Went calibrating in circles for about 10 times and guess wat!!!! It starts up!!!!
Now my conclusions are as good as anyones, it cant be an hardware issue. I am trying to find a solution so I can reflash my ROM and go to a stable version and live with my phone atleast for an year.
The Mystic ROM lite version has touch response software built in, Could this be the issue.
Anyones got any idea let me know
Hello fellow HTC HD2 users,
I have a problem with my HTC HD2 for some time, its in the touchscreen and the problem is that in the beginning my phone sometimes wouldnt respond, random locks, and a weird defect that causes a problem so i cant touch the W key on the onscreen keybord .. on all ROM/RADIO combi ive tried, also on Android builds from my SD.
But today my phone screen is black and frozen it seems, even the bootloader is a black screen, i tryed a new HSPL flash, Radio actualy everything, but it seems that its dead (only backlight lights up).
Now ive read something about older batches of phones that have this problem .. now my brother also has a HTC HD2 but got it later then me, and first thing that i noticed when i wanted to flash his software, was that he already had the 1.66 rom, while mine was with 1.48 out of the box. (ye its software but ..)
I will return it to the store ofcourse. (reflashed stock spl/rom from htc site with sd card method, just 2 days ago )
Anyone know if they will replace my phone for a new one?
Or will they just fit in a new screen?
Or mabye some tips to solve this problem?
Thanks
Tips to help you solve it ? i doubt there is .
But it may be the screen is defected .. did you drop it on the floor or something ?
And since the problem is in Android AND WinMo thenyou should consider a replacement .
Good Luck
I did bring it to the store today, now 3-4 weeks without my HD2 :'(
Anyway, no it never dropped, i always take good care of my phone, expecialy with a big screen as the HD2, it seems that this problem lies in older devices of the HD2.
Btw check this:
http://wmpoweruser.com/strange-htc-hd2-touch-screen-behaviour-is-your-device-affected/
The youtube video shows what i ment in the OP, screen 1 is MY phone, screen 2 is my Brothers phone (not actualy on that vid, but its the same resemblance).
Maybe helping people that have the same problem.