I got a life several days ago, then i flashed the Xda_Atom_Life_WM6_WWE_RC2170507B2.exe, reset the divice, i found that there is no gsm!
radio and imei read "not ready"
what is the problem? how to fix it?
thanks very much!
and i could not enter the bootloader mode by pressing the recording button and rest hole.
try to remove the battery for 5~10 minutes, then put back the battery without SD card, press the camera button + power button to switch on the phone.
可以同步，可以进系统，但是就是没有信号，超级怪！！！
dcoloane, I tried what u said, just witched on the phone, nothing else happened.
Can anyone help me?
cranesky said:
and i could not enter the bootloader mode by pressing the recording button and rest hole.
Click to expand...
Click to collapse
It is Camera Button + Reset Button
have you try to replace your sim card with another one?
Did you check wether the Device is set to UMTS only? This is quite often the cause for no connection.
Related
hi. i want to hard reset my atom life. how can i do it?
do assist me. need it as soon as possible. thanks.
This is grabbed from another forum after a google search...
"It's normally press-n-hold the on/off button --> press the reset button.
When the green+red button command appears, let go of the on/off button and press the green n red button simultaneously.
This is the standard Atom series hard reset method. Not sure for Atom Life though"
First, Hold Power button and insert stylus into the reset hole
release power button and remove stylus. you should now see message on the screen saying about hard reset, press and hold both green and red button at the same time until. when it's done system will reboot itself.
what risk if when hard reset the batt getting low?
Hard reset normally takes less than 5 seconds to clear out your older settings. Though you better charge it before hard resetting.
hehe.. if the batt getting low and die . so how?
hendranata said:
hehe.. if the batt getting low and die . so how?
Click to expand...
Click to collapse
connect your charge, wait 5 minus then hard reset, go go
will there be any effect on the data saved in my documents and memory card?
you can read the Manual
thedonbk said:
will there be any effect on the data saved in my documents and memory card?
Click to expand...
Click to collapse
a.f.a.i.k, ther wont be any critical defects on ur mem-card n my docs.
anyway, hard-reset clears off the saved data in ur "my docs". so it doesnt matter anyway.
its better to avoid such situation wher u dont have much batt left, and still go do a hard-reset.
a hard-reset normally take onli like less than 4-5mins.
unlike flashing in new rom from dsuu mode or sd-flashing mode, wher its safe to keep a 70% lvl of batt b4 start flashing.
hm.. hold power on/off and reset ... i try twice fail.. how?
yes..same with me..how?
hendranata said:
hm.. hold power on/off and reset ... i try twice fail.. how?
Click to expand...
Click to collapse
To hard reset.
Keep the Power On button pressed. Then put the stylus in the reset hole. Dont leave the power button till you see the hard reset screen.
This is the exact way. I've tried it so many times
1. Hold the RECORD button (the one near the camera button)
2. While RECORD button pressed, with your stylus, push the softreset button (the one at the bottom, in the hole)
3. Hold both button for about 5 seconds
4. Release ONLY the soft reset button first
5. Then the screen will display some hard reset sequence
6. Then you can securely release the RECORD button
Attention, those are the step by step. Missing one sequence, and it will be failed
But, after the hard reset menu apeared, i don't know which menu to select if i need to hard reset my atom life. Any help with this?
Hello, i`ve upgraded my s2 to ics and i have a inconvenient.On gingerbard, holding the power off button would showed up some shorcuts including the 3g activation.On ics if I hold the power off button it shutdowns directly.Is there any possibility to make it do the same action as on gingerbard?Is there any alternative for activating the 3g without going deep into the settings?Thanks
saddameu said:
Hello, i`ve upgraded my s2 to ics and i have a inconvenient.On gingerbard, holding the power off button would showed up some shorcuts including the 3g activation.On ics if I hold the power off button it shutdowns directly.Is there any possibility to make it do the same action as on gingerbard?Is there any alternative for activating the 3g without going deep into the settings?Thanks
Click to expand...
Click to collapse
That's strange. I don't think that holding power shuts it down directly without power menu (unless you hold it for 8-10 seconds, then yes it's normal, but I don't think that's what you mean). Maybe something went wrong during the update. Try reflash maybe, or reset to default...
antonio1475 said:
That's strange. I don't think that holding power shuts it down directly without power menu (unless you hold it for 8-10 seconds, then yes it's normal, but I don't think that's what you mean). Maybe something went wrong during the update. Try reflash maybe, or reset to default...
Click to expand...
Click to collapse
ive tried like 4-5 diff ics versions today.Everything is working perfectly but the phone shutdowns directly when I keep it pressed instead of showting shorcuts like gingerbard does.Maybe i`m missing some option, some check box unchecked but I didin`t find any option.
saddameu said:
ive tried like 4-5 diff ics versions today.Everything is working perfectly but the phone shutdowns directly when I keep it pressed instead of showting shorcuts like gingerbard does.Maybe i`m missing some option, some check box unchecked but I didin`t find any option.
Click to expand...
Click to collapse
Official Samsung firmwares? I find it really strange. It should have a power menu. (you are holding it just 2-3 seconds right? Not 8 so you are forcing it to shut down).
I'm sorry, some other expert will help you. But stock firmwares and custom ROMs, they all have power menu. I've never seen any firmware/ROM that shuts down directly.
Sounds like you're missing /efs/imei/keystr
Create a file called keystr in /efs/imei and put "ON" in it.
wow, you are a genius.Everything was fine and working except that holding thing and I also had no screenlock, it was just getting to the menu if i would have pressed home button or power off.I fallowed your instructions and they were both fixed.Thank you very much.
[Q] Please!!! help me I can not reboot LG OPTIMUS G E970 (Attach picture)
I open hidden menu ( 3845#*970# ) and test device.
when i test menu Fastboot, I can not go back.
How I do?
sirasest said:
[Q] Please!!! help me I can not reboot LG OPTIMUS G E970 (Attach picture)
I open hidden menu ( 3845#*970# ) and test device.
when i test menu Fastboot, I can not go back.
How I do?
Click to expand...
Click to collapse
When you get to that screen, press Volume Down > pause > volume down > power button. This will boot you to recovery. From here I would recommend doing a nandroid, then factory reset, then clean install a new rom. Let me know how that works out for you, or if you need further assistance.
ousoonerchase said:
When you get to that screen, press Volume Down > pause > volume down > power button. This will boot you to recovery. From here I would recommend doing a nandroid, then factory reset, then clean install a new rom. Let me know how that works out for you, or if you need further assistance.
Click to expand...
Click to collapse
If you look at the picture the bootloader is locked. I would try unplugging it and holding power until it reboots.
adfurgerson said:
If you look at the picture the bootloader is locked. I would try unplugging it and holding power until it reboots.
Click to expand...
Click to collapse
Good call @adfurgerson, didnt see that. Yeah you could do that, or try the forced reboot with volume down + power button for 10 seconds, then when it goes dark press and hold the power button. After that you could try the battery pull to hopefully not destroy your data. Then he could try LGPNST teenybin. You still have some options, and seeing that screen means you should be fine with just a little bit of work. I hope it works out!
ousoonerchase said:
Good call @adfurgerson, didnt see that. Yeah you could do that, or try the forced reboot with volume down + power button for 10 seconds, then when it goes dark press and hold the power button. After that you could try the battery pull to hopefully not destroy your data. Then he could try LGPNST teenybin. You still have some options, and seeing that screen means you should be fine with just a little bit of work. I hope it works out!
Click to expand...
Click to collapse
Battery pull? I think you can't remove the battery off this phone
ousoonerchase said:
Good call @adfurgerson, didnt see that. Yeah you could do that, or try the forced reboot with volume down + power button for 10 seconds, then when it goes dark press and hold the power button. After that you could try the battery pull to hopefully not destroy your data. Then he could try LGPNST teenybin. You still have some options, and seeing that screen means you should be fine with just a little bit of work. I hope it works out!
Click to expand...
Click to collapse
That screen show me when I chaged batterry and unplug screen black.
I try but LG E970 can not reboot.
Battery can not pull out.k
sirasest said:
That screen show me when I chaged batterry and unplug screen black.
I try but LG E970 can not reboot.
Battery can not pull out.k
Click to expand...
Click to collapse
Battery can be dissconnected by taking phone apart there are a few guides in general section. You might be able to force a reboot if you can get to download mode. Plug phone into USB then press volume up, volume down, and power all at same time. If it goes into download mode unplug phone and hold power until it reboots. If no luck that way try power and volume down to try to get to factory reset screen.
Hi,
My phone has a faulty power button and I'm unable to get it fixed. I've found easy work-arounds for it for locking and unlocking the phone. However, I'm not sure how to turn on the phone if it's switched off.
When I connect the charger, even if the battery is 90% it won't turn on on its own...
njr08 said:
Hi,
My phone has a faulty power button and I'm unable to get it fixed. I've found easy work-arounds for it for locking and unlocking the phone. However, I'm not sure how to turn on the phone if it's switched off.
When I connect the charger, even if the battery is 90% it won't turn on on its own...
Click to expand...
Click to collapse
Have you ever solve the problem? I've also the same faulty button..and I don't know how to power on without this button
maranric said:
Have you ever solve the problem? I've also the same faulty button..and I don't know how to power on without this button
Click to expand...
Click to collapse
Nope, the only way I could turn it on was to open the back cover (very painful process) and then press the button area with a pin.
Couldn't get it fixed, so I had to change the phone.
I think there are possibilities in rooted phones, but otherwise the best thing to do is to keep a battery alarm at 30% or more, and keep it on charging whenever you can to avoid a power off. In power on, there are many ways of locking the screen in the MI UI.
njr08 said:
Hi,
My phone has a faulty power button and I'm unable to get it fixed. I've found easy work-arounds for it for locking and unlocking the phone. However, I'm not sure how to turn on the phone if it's switched off.
When I connect the charger, even if the battery is 90% it won't turn on on its own...
Click to expand...
Click to collapse
njr08 said:
Nope, the only way I could turn it on was to open the back cover (very painful process) and then press the button area with a pin.
Couldn't get it fixed, so I had to change the phone.
I think there are possibilities in rooted phones, but otherwise the best thing to do is to keep a battery alarm at 30% or more, and keep it on charging whenever you can to avoid a power off. In power on, there are many ways of locking the screen in the MI UI.
Click to expand...
Click to collapse
Thanks. I installed Blocco Schermo - Simi Studio v.3.21 , a simple app to lock the screen...and when i flagged the option "show in notification area" , the problem magically disappeared.. The Power On/Off button started to work again. I think it was an hardware problem (because the problem has come up after the phone was at the sunlight for hours in my car and went very hot) but now i think it's obviously a software problem.
Hi guys, I got the same problem too. Unfortunately, I drained my batt while playing games. So the problem now is I can't turn it on. Any idea how to turn on the phone without using the power button?
I solved it
Hi guys i solved a problem! You should hold main button + down volume button for 10-20 seconds. Then, when MI Remote opens, stay on the reboot and wait about 3 minutes, then stay on the reboot systems as well. Great work!
just change the volume flexible. its also not took much cost.
Is there any software or commands I could use to diagnose my phone over USB? The screen is black, even during boot (no logos), but the phone is still working in the background. The notification LED blinks normally, menu and back button lights up when pressed, and it even rings when someone calls, though I can't see who it is b/c of the black screen. The screen is not cracked or damaged, and I didn't drop it, so not sure why this is happening. I want to test the GPU or other components before I put down a lot of money for a new screen and it no resolve the issue.
Phone is a rooted SM-N910V that has been working great for 3 months.
Thank you!
Modify_inc said:
Is there any software or commands I could use to diagnose my phone over USB? The screen is black, even during boot (no logos), but the phone is still working in the background. The notification LED blinks normally, menu and back button lights up when pressed, and it even rings when someone calls, though I can't see who it is b/c of the black screen. The screen is not cracked or damaged, and I didn't drop it, so not sure why this is happening. I want to test the GPU or other components before I put down a lot of money for a new screen and it no resolve the issue.
Phone is a rooted SM-N910V that has been working great for 3 months.
Thank you!
Click to expand...
Click to collapse
Hi , try with key kombination .
1. Make sure your phone is OFF
2.Now Press toghether Vol + and power button and hold like that until second vibration (reboot)
3. If that doesn't work try with another combination .
Vol - and Power button
Vol + & Home button & Power button for about 10 second
Vol - & Home button & Power button for about 10 second
Good Luck
Teddy Lo said:
Hi , try with key kombination .
1. Make sure your phone is OFF
2.Now Press toghether Vol + and power button and hold like that until second vibration (reboot)
3. If that doesn't work try with another combination .
Vol - and Power button
Vol + & Home button & Power button for about 10 second
Vol - & Home button & Power button for about 10 second
Good Luck
Click to expand...
Click to collapse
Thanks for the suggestions, though I have already tried all those plus other things.
I've left the battery out for over a day, removed sim card, held power button in to drain any residue power.
I'm lost as to why all of sudden the black screen. Hoping there's a way to test the phone to confirm if its the lcd or something else like the gpu chip. On a laptop you could plug a monitor in the vga port, don't guess phones have this option
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Modify_inc said:
Thanks for the suggestions, though I have already tried all those plus other things.
I've left the battery out for over a day, removed sim card, held power button in to drain any residue power.
I'm lost as to why all of sudden the black screen. Hoping there's a way to test the phone to confirm if its the lcd or something else like the gpu chip. On a laptop you could plug a monitor in the vga port, don't guess phones have this option
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
I read that the phone was rooted so maybe that custom rom has some bug and that way you get black screen .
Try to flash him back to stock firmware and see if the problem is solved .
It is just rooted on the standard firmware, I didn't install any custom firmwares. But I was wondering if I could possibly reflash it from a backup I made with twrp. I cant get to recovery, well actually I could if I new the exact steps since everything works, I just cant see crap.
Is this even possible or is there another way to access twrp over the usb?
Sent from my [device_name] using XDA-Developers Legacy app