I just installed yesterday the Altell ROM in my Sprint Mogul phone and everything look work fine except the MMS, thanks Olipro for your work;
I used this configuration:
Server name: Sprint
Gateway: (leave in blank)
Port number: 80
Server address: http://mms.sprintpcs.com/servlets/mms
Connect via: (here the Sprint is not available The Internet and doesn't worked)
Sending size limitation: 300kb
WAP: Select WAP 2.0
i had the same problem. find a cab on xda for arcsoftmms and install it. then soft reset. after resetting, uninstall the cab you just installed. soft reset again.
now go into your mms settings and set up a new default with the settings you previously used.
It worked for me. Give it a shot. I don't know what the arcsoft installation does that corrected my problem, but it's fixed and working perfectly
later
Im using the same settings and everything is working fine if is under 300k... anyone know hoe to increase the size? the drop down menu on show 300k.
Thanks!
Vertig0 said:
Im using the same settings and everything is working fine if is under 300k... anyone know hoe to increase the size? the drop down menu on show 300k.
Thanks!
Click to expand...
Click to collapse
i have mine currently set at 585K in the drop down menu.
it's just a registry setting you need to change
HKLM-SOFTWARE-ARCSOFT-ARCSOFT MMS-CONFIG-mm1-96352-
then increase the values for both the WAP1DefaultSize and WAP2DefaultSize
Later
utexascg said:
i had the same problem. find a cab on xda for arcsoftmms and install it. then soft reset. after resetting, uninstall the cab you just installed. soft reset again.
now go into your mms settings and set up a new default with the settings you previously used.
It worked for me. Give it a shot. I don't know what the arcsoft installation does that corrected my problem, but it's fixed and working perfectly
later
Click to expand...
Click to collapse
Hi, thanks for you answer, just a question what you did after uninstall the arcsoftmms because i don't see no more the MMS folder in my Pocket Outlook and the settings for MMS is there but you i can't see either where you can create one MMS Folder......well thanks in advance....
just wanting to make sure i'm understanding, you've already installed and then uninstalled the arcsoft, correct?
If so, then just access the mms setting and configure it with the information that was in the previous post. Once you've done that you should be able to go into your sms messaging and select "new mms" and that should be it
Any links to the arcsoftmms that you used?
cab file is attached.
again, i don't take credit for the file. i found it on xda i just don't remember where
later
utexascg said:
i have mine currently set at 585K in the drop down menu.
it's just a registry setting you need to change
HKLM-SOFTWARE-ARCSOFT-ARCSOFT MMS-CONFIG-mm1-96352-
then increase the values for both the WAP1DefaultSize and WAP2DefaultSize
Later
Click to expand...
Click to collapse
THANK YOU!!!
utexascg said:
just wanting to make sure i'm understanding, you've already installed and then uninstalled the arcsoft, correct?
If so, then just access the mms setting and configure it with the information that was in the previous post. Once you've done that you should be able to go into your sms messaging and select "new mms" and that should be it
Click to expand...
Click to collapse
Yes i did it, first time using a Arcsoft MMS that i have and one more time using the version you have but i don't any Folder in my Messaging (Pocket Outlook) after this but i using the HTC Home Plugin and when i hit the Message Button then i can see the inbox folder and selecting new create a message eith Pictures or Multimedia staff but when i hit send he start the like uploading (couting percentage slow depend of the size) but i at the end i got a message saying ... " Message could not be send. Unsupported message format, Operation failed!. Version cannot be supported......
so one second... we have to install and then uninstall the arcsoft one to make this work?
does anyone else think this is a silly way to go about it?
What does the installation do? its probably as simple as changing some registry settings.
Dishe said:
so one second... we have to install and then uninstall the arcsoft one to make this work?
does anyone else think this is a silly way to go about it?
What does the installation do? its probably as simple as changing some registry settings.
Click to expand...
Click to collapse
Actually there is a registry modification file to fix this without the uninstall staff...i found this in PPCGEEKS
yangers said:
I just installed yesterday the Altell ROM in my Sprint Mogul phone and everything look work fine except the MMS, thanks Olipro for your work;
I used this configuration:
Server name: Sprint
Gateway: (leave in blank)
Port number: 80
Server address: http://mms.sprintpcs.com/servlets/mms
Connect via: (here the Sprint is not available The Internet and doesn't worked)
Sending size limitation: 300kb
WAP: Select WAP 2.0
Click to expand...
Click to collapse
Those are the correct settings -- Connect via "choose alltel wireless" --
MMS should be fine after that. Its the same internet connection as creating your own Sprint connection.
yangers said:
Actually there is a registry modification file to fix this without the uninstall staff...i found this in PPCGEEKS
Click to expand...
Click to collapse
How do you apply this reg edit? clicking on a .reg file opens up RegEdit on the PPC, but alas, it doesn't actually DO anything!
Dishe said:
How do you apply this reg edit? clicking on a .reg file opens up RegEdit on the PPC, but alas, it doesn't actually DO anything!
Click to expand...
Click to collapse
Is just double click and will be added (modify) to your REGISTRY.........
I have tried all of these settings and still am not gettin mms to work. Everything is set corretcly. are there any new updates?
all yo have to do is change the server address to http://63.215.195.152 and it should fixx all of your issues
Related
Can anybody here give me the mms settings for smart network?
tnx in advance
As far as I know the Wallaby doesn't support MMS, but I could be wrong or you could find some third party software to support it, but out of the box it doesn't.
Regards,
Neil.
evan_gerard said:
Can anybody here give me the mms settings for smart network?
tnx in advance
Click to expand...
Click to collapse
Hi evan_gerard,
Let me know if you already got your mms working on your wallaby. I have mine working using EZWAP and manually configuring Smart's IP address. I'll post the settings here if you need them. Happy new year!
morph751 said:
evan_gerard said:
Can anybody here give me the mms settings for smart network?
tnx in advance
Click to expand...
Click to collapse
Hi evan_gerard,
Let me know if you already got your mms working on your wallaby. I have mine working using EZWAP and manually configuring Smart's IP address. I'll post the settings here if you need them. Happy new year!
Click to expand...
Click to collapse
YES MORPH751 pls do help me with the settings, and where can I get ezwap, tnx in a million
Get EZWAP here:
http://www.ccsleeds.co.uk/stuff/ezwap25xda.zip
Thanks to Pete K for the link.
Download and install EZWAP to your wallaby. You need to configure the settings first before MMS and GPRS could work.
As for the settings I'll post them here tomorrow, I documented the procedure and settings (after trial and error) but it's in my home PC. Hope it works for you.
tnx a lot
MMS / GPRS Settings for Smart Network via EZWAP 2.5
Set up GPRS:
1. Start> Settings> Connections> Connections
2. Modify "Internet Settings"
3. Click "New":
Enter a name for the connection: SMART GPRS
Select a modem: Cellular Line (GPRS)
Baud Rate: 19200
4. Click "Advanced":
TCP/IP Settings:
Use server assigned IP address
Enable Use software compression
Enable Use IP Header Compression
Name Servers:
Click "Use server specific address"
DNS: 202.57.96.3
Alt DNS: 202.57.96.4
WINS/Alt WINS: 0.0.0.0
5. Click "OK"; "Next"> SMART GPRS
Access Point Name: Internet
6. Finish
7. Dialling Locations> Connections:
Location: Mobile
Enable Tone Dialling
Area Code: 02
Country Code: 63
8. Click "OK"; End
Set up MMS via EZWAP:
1. Open EZWAPv2> Tools> Options
2. General> Connection: SMART GPRS; Connect Automatically
3. Connection> Connection Type:
Gateway: Enabled
Address: 10.102.61.46
Port: 9201
Disabled: Connectionless Gateway; WTLS secured connection
Timeouts: Default
4. Push:
Enable Push
Connection Type: Address: Blank; Port: 2948
Enable Connectionless Push Gateway
Disable WTLS Secured Connection
5. MMS: MMS Settings:
Message Server: http://10.102.61.238:8002
Sender Address Type: Phone Number
Sender Address: +63920nnnnnnn (enter your phone number
here)
6. MMS Options:
MMS Message Options:
Message Expiry: Max
Enable All
7. Save; End
Good luck!
mms gprs settings
tnx in a million morph751, anyway do you have one for globe?my friend is asking bout it also, tnx in advance
Re: mms gprs settings
evan_gerard said:
tnx in a million morph751, anyway do you have one for globe?my friend is asking bout it also, tnx in advance
Click to expand...
Click to collapse
I think it's the same procedure for Globe. You just need to get Globe's IP address and DNS server addresses. Unfortunately, I don't have Globe's settings. You can probably inquire in Globe centers or it may be available at their website. Hope you enjoy your MMS!
just go to the ftp site check previous posts.. if you need a copy of the cab files (containing mms settings for both smart and globe.. pati sun) just post yer email address and i'll send them to ya.. the wallaby can send and receive mms.. you just need to download the right cab files... im using arcsoft mms composer version 1.6.0.14 and it works perfectly... :wink:
just go to the ftp site check previous posts.. if you need a copy of the cab files (containing mms settings for both smart and globe.. pati sun) just post yer email address and i'll send them to ya.. the wallaby can send and receive mms.. you just need to download the right cab files... im using arcsoft mms composer version 1.6.0.14 and it works perfectly... :wink:
just go to the ftp site check previous posts.. if you need a copy of the cab files (containing mms settings for both smart and globe.. pati sun) just post yer email address and i'll send them to ya.. the wallaby can send and receive mms.. you just need to download the right cab files... im using arcsoft mms composer version 1.6.0.14 and it works perfectly... :wink:
HELP on MMS Diamond
I'm sure since it's all Windows the settings are either the same or similar right?
I have a diamond, and every time i receive a MMS picture i get charged 10 pesos for GPRS internet connection. Called smart, they said Receiving MMS is free and it is my phone that has a problem. They think that the MMS triggers something, a program maybe, that connects to the GPRS every time i receive MMS pictures.
THey said they cannot fix my phone since they do not carry distribute HTC.
What do i do? Any ideas please
I'm using HTC Fuze here in the Philippines. I just used the NetworkWizard.cab I downloaded. Run it, reboot, and everything works.
Alltels new rom enabled picture messaging on my phone, but I'm not to happy with the rom.
I would like to go back to dcd's 6.1 rom but I would like to keep my picture messaging.
I thought I saw something where someone extracted all the added **** from Alltels rom, yet I cannot find it.
Americanmetal said:
Alltels new rom enabled picture messaging on my phone, but I'm not to happy with the rom.
I would like to go back to dcd's 6.1 rom but I would like to keep my picture messaging.
I thought I saw something where someone extracted all the added **** from Alltels rom, yet I cannot find it.
Click to expand...
Click to collapse
There has been quite a bit said about it. So far, i'm not positive if any Alltel user has gotten MMS to work. One of the threads is here and there are several other at the beginning of DCD's "Cooked Roms" thread or at the beginning of this 3.0.4 thread..i can't remember.
Americanmetal said:
Alltels new rom enabled picture messaging on my phone, but I'm not to happy with the rom.
I would like to go back to dcd's 6.1 rom but I would like to keep my picture messaging.
I thought I saw something where someone extracted all the added **** from Alltels rom, yet I cannot find it.
Click to expand...
Click to collapse
When installing the ROM do not add the Arcsoft 5.0.31.7 MMS. Add this MMS although it is not the new one it is the only one that I know that works.
Arcsoft MMS 3.0.26.12c
Server Name: Alltel MMSC
Gateway: mms.alltel.com
Port Number:8080
Server Address: http://mms.alltel.com/servlets/mms
Connection via: Alltel Wireless
Sending Size Limitation: 300K
WAP: WAP 2.0
Thanks I'll give it a try later on this week!
dwertz said:
When installing the ROM do not add the Arcsoft 5.0.31.7 MMS. Add this MMS although it is not the new one it is the only one that I know that works.
Arcsoft MMS 3.0.26.12c
Server Name: Alltel MMSC
Gateway: mms.alltel.com
Port Number:8080
Server Address: http://mms.alltel.com/servlets/mms
Connection via: Alltel Wireless
Sending Size Limitation: 300K
WAP: WAP 2.0
Click to expand...
Click to collapse
Yup. That is how I got mine to work.
Mine works as is with the new Alltel rom
I just want to go back to 6.1 with threaded ****.
All you need to do is install fresh with newest kitchen and dont check the arcsoft part. do not install that. then go to lennysh.com and install the arcsoft for alltell and you will be fine. I have ****ed with my phone as far as i can go and i have always had picture messagin. I have the newest arcsoft installed and my mms works flawlessly. I even can send over 300k limits.
silentjoker said:
All you need to do is install fresh with newest kitchen and dont check the arcsoft part. do not install that. then go to lennysh.com and install the arcsoft for alltell and you will be fine. I have ****ed with my phone as far as i can go and i have always had picture messagin. I have the newest arcsoft installed and my mms works flawlessly. I even can send over 300k limits.
Click to expand...
Click to collapse
How did you get arcsoft 5.0.31.7(newest) to work on alltel? Lennys version(the one I have..and only one I know about 3.0.26.12c ) isnt 5.0.31.7. So I was wondering what version you have that allows you to send over 300k? Not trying to doubt you and all but just very interested.
the newest version. i dont know why it does send over that limit. if i create a mms video or picture and hit send threw mms it loads it into the mms and will allow me to send. but sometimes if i manually put it in it says it over the 300k limit dunno if its a glitch or what.
silentjoker said:
the newest version. i dont know why it does send over that limit. if i create a mms video or picture and hit send threw mms it loads it into the mms and will allow me to send. but sometimes if i manually put it in it says it over the 300k limit dunno if its a glitch or what.
Click to expand...
Click to collapse
Can you supply the cab on lennys you used? thanks
i used the arcsoft from the actual website the lennysh one is like ending in .12c
Can you supply the link or cab for it?
FWIW I simply installed the 3.xxx cab from lenny's on top of the included version and it all appears to work. probably not a recommended practice, but if my phone explodes i'll be back to whine.
dwertz said:
Arcsoft MMS 3.0.26.12c
Click to expand...
Click to collapse
Link's dead
here's a link to the thread
I can receive messages but for some reason the message I send are not received by others
Americanmetal said:
I can receive messages but for some reason the message I send are not received by others
Click to expand...
Click to collapse
1st: When you installed the ROM you did not add Arcsoft 5.0.xx.xx correct?
2nd: Did you install the Arcsoft 3.0.26.12c cab or did you change it to OEM?
3rd: Did you check your settings and make sure they are below and they are set as the default?
Try to explain in a little more detail what it is doing?
Server Name: Alltel MMSC
Gateway: mms.alltel.com
Port Number:8080
Server Address: http://mms.alltel.com/servlets/mms
Connection via: Alltel Wireless
Sending Size Limitation: 300K
WAP: WAP 2.0
dwertz said:
1st: When you installed the ROM you did not add Arcsoft 5.0.xx.xx correct?
2nd: Did you install the Arcsoft 3.0.26.12c cab or did you change it to OEM?
3rd: Did you check your settings and make sure they are below and they are set as the default?
Try to explain in a little more detail what it is doing?
Server Name: Alltel MMSC
Gateway: mms.alltel.com
Port Number:8080
Server Address: http://mms.alltel.com/servlets/mms
Connection via: Alltel Wireless
Sending Size Limitation: 300K
WAP: WAP 2.0
Click to expand...
Click to collapse
1. Wasn't included in the rom's kitchen; I got the cab from
leary said:
here's a link to the thread
Click to expand...
Click to collapse
There^
2. I installed 3.0.26.12C
3.My settings are exactly what you listed.
Americanmetal said:
1. Wasn't included in the rom's kitchen; I got the cab from
There^
2. I installed 3.0.26.12C
3.My settings are exactly what you listed.
Click to expand...
Click to collapse
Try importing this into the registry, soft reset and test. If not then I would run sprite backup or spb backup and hard reset and just install the Arcsoft and see if it works. It should work without any configurations.
dwertz said:
1st: When you installed the ROM you did not add Arcsoft 5.0.xx.xx correct?
2nd: Did you install the Arcsoft 3.0.26.12c cab or did you change it to OEM?
3rd: Did you check your settings and make sure they are below and they are set as the default?
Try to explain in a little more detail what it is doing?
Server Name: Alltel MMSC
Gateway: mms.alltel.com
Port Number:8080
Server Address: http://mms.alltel.com/servlets/mms
Connection via: Alltel Wireless
Sending Size Limitation: 300K
WAP: WAP 2.0
Click to expand...
Click to collapse
Try Alltel.net instead of .com everywhere you see .com. This is what worked for me to get MMS working on my Alltell PPC 6800.
I downloaded and installed the GC Arcsoft MMS 5.0.70.24 for VZW but i can't get my phone to send or receive pictures. Does anybody know the server info to enter or what i need to do to get it to work?
Be sure your 10 digit phone number(##########) is in the following registry entry:
HKLM\Software\Arcsoft\ArcsoftMMS UA\Config\mm1\WspHeader\X-VzW-MDN
I followed it all the way to WspHeader and i couldnt find X-VzW-MDN.
do you have a data plan ?
do you have a carrier installed?
Yeah i do, my internet is working and everything.
Having the same problem. Everything else is working fine.
tree20002 said:
I downloaded and installed the GC Arcsoft MMS 5.0.70.24 for VZW but i can't get my phone to send or receive pictures. Does anybody know the server info to enter or what i need to do to get it to work?
Click to expand...
Click to collapse
I've had this problem for months. I wasn't able to get it to work so I finally just gave up on sending and receiving pictures. I installed WM 6.5 built 21159 - Beta 5 ROM the other day and tried to send pics again, but still nothing. It really sucks.
His arcsoft cab has a setup DLL that reads the MDN from the registry and puts it into that key for arcsoft.... If you installed the carrier cab after the MMS cab then that would explain why its not there.... I'd hard reset, then install the carrier cab, then reboot, then install the arcsoft cab.... I have had to install the mms cab twice before it worked right.....
GeLopez said:
do you have a data plan ?
do you have a carrier installed?
Click to expand...
Click to collapse
Is a data plan required for pix messages?
ibenjakinov said:
Is a data plan required for pix messages?
Click to expand...
Click to collapse
some kind of plan is required so you can actually receive a connection from the data network. you can get a pay as you go plan, but especially with WM phones this is a really bad idea because you can rack up alot of usage really quickly. if you dont have a data plan than you wouldnt be able to connect anny app to the internet
I got it to work. Just make sure you install the carrier cab first then the MMS cab. you might have to reinstall the MMS cab a couple of times, but it should work.
I am having this problem too. After installing the MMS button does not show up in messaging when sending media.
I am having trouble sending a picture message through MMS. I installed this - http://forum.ppcgeeks.com/showthread.php?t=59412 - Arcsoft MMS. It now allows me to insert the pictures in my message, but when I go to send it it says:
"In order to send/download MM messages, the current active connection may be closed (this may affect other applications in use. Do you want to continue?" so I hit menu > yes.
Then is says:
Message delivery failed. Or Message receipt failed.
I am running NFSFANs Rom 111
anyone that can help?
GatorsUF said:
anyone that can help?
Click to expand...
Click to collapse
who is your carrier what/who's version of arcsoft did u install. did you check your settings?
Service: Alltel which is now Verizon
Version: SPRINT Arcsoft MMS 5.0.70.24. Threading MMS works! (Updated 3-2-09)
Cabs: Sprint Arcsoft MMS 5.0.70.24.cab and Sprint Arcsoft MMS 5.0.70.24-pm.cab
Neither version would work with my service, I have Alltel and the rls says Sprint, so that may be my problem. All I want to do is send picture messages. My phone can do almost anything I want but it can't send a picture message that my old Nokia from 3 years ago could do?
Thnx for the help btw
P.S. another odd bug with that Arcsoft program is when I go to check my emails and hit "Mark All as Read" it opens the Arcsoft settings...wierd...
ok so go to your inbox then press menu/mms options(may say pics and video options)/servers/alltel. if alltel isnt there just click on the default. if alltel is there and not the default-set it to default and delete others. then open the default. here is your settings.
server name: Alltel MMSC
Gateway: mms.alltel.com
port:8080 (try 8080 first if it doesnt work try just 80)
server address: http://mms.alltel.com/servlets/mms
connect via: the internet
send limit: i have mine set 100k currently
if you dont care to use an older arcsoft just install this it should work right from the get go. im pretty sure its calkulins. ive used it 4ever.
any chance you can get this app to work with the TELUS network?
That would be great if it worked for Telus...
Finally got a custom ROM on my phone, NFSFANs, and I must say I really like it, but for some reason I am unable to MMS. I looked through all the places i thought would be obvious settings, but i cant find anything
anyone else experience this?
same issue
i have been haveing the same issue on my touch pro, i dont see were to fix it when i try to send it starts to then says unable to send does any one know of a fix for this, i am useing Energy.HERMAN.23518.StandardM2.5_27.
use this
use this cab, it appears that messaging is still not ready for the new 2011 builds...
This will disable the HTC Messaging and take you back to the winmo messaging.
You also need the second cab to take your phone back to what sense2.1 used and it should work...
There is also a third file attached, that one you install by itself, you have to go to the "all messages" then you have to go to the menu>options>settings and put your settings.
Search on it a little more, If I find the full information again I will let you know. I read on it last night and got my wifes touch pro2 to mms again so this should work for you too...
Maybesz?
I beleive this may be what your after, these settings are carrier specfic in order to get MMS working
HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\MM1 Default Setting Cricket MMS and Change WAP default Port 1&2 to 8080 and WAP Default Time Out to 10000
HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\MM1\MMSCSetting\Cricket MMS Ensure Gateway Port is 8080 ISP is Cricket MMS, MmscURI is set to http://mms.mycricket.com/servlets/mms , Name is Cricket MMS, Ensure the next 4 settings WAP1RecvDefault Size, WAP1Send WAP2 Recv and WAP2 Send are set to 1024000 WAPType to 1 (WAPType to 1 Ensures WAP 2.0)
WspHeader Accept: application/vnd.wap.multipart.related
X-Cricket-MDN this is your 10digit cell number (this might say X-Verizon or X-Sprint Change the value name to X-Cricket-MDN) Value Data 555-555-5555 < of course put in your own phone number no dashes.
Under UI\Domain http://mms.mycricket.com/servlets/mms
Under UI\SizeLimit WAP1RecvLimit 1,2,3 set everything on that page (12 settings in all) 1024000 (this is part of your 1000K send and receive limit)
HKLM /software/arcsoft mms ua/config/UI
find EnableServerEdit and change it from 0 to 1
HKCU\Software\Microsoft\Windows\CurrentVersion\Int ernet Settings Where it says Connections, Delete that entire string Hold down stylus on Connections circle it and delete it, This is what keeps the MMS from sending. Bad thing is every time you open explorer it re-writes this registry. To solve that many of us have just used something else besides Explorer. Like Opera, Firefox Mobile or Skyfire.
You can still use these browsers without writing the Connections Value. If you don’t want to use anything but Explorer, you are going to have to go into this registry file and delete the Connections string every time to send MMS or until someone comes up with a registry hack to Auto delete this value every time you close IE …Close Regedit.
Now go to your messages and click menu/MMS options and then click server and click add new. Add new or if you already have one called something else just click it and click edit...you need to change these settings to
Server Name Cricket
Gateway leave blank
Port Number 8080
Server address http://mms.mycricket.com/servlets/mms
Connect Via Cricket MMS
Sending limit (should be 1024000 if you changed these settings correctly in regedit)
Wap version Wap 2.0 (Wap 2.0 should be pre selected, if it is don’t touch it. If it keeps reverting back to 1.2 when you click close? Go back into regedit and select WapType 1 as mentioned previously, this forces it into WAP 2.0 without it MMS won’t work.) Now if you have more than 1 select the cricket one you just configured and hit set as default then go back to HKLM\Software\Arcsoft\Arcsoft MMS UA\Config\MM1\MMSCSetting\Cricket MMS and delete the other configuration, when you go back into settings CricKet should be the only one there and it should be default.
Start\Settings\Connections\Connections Under the General Tab Enter Cricket. Under the Modem Tab put in Cricket Mobile Web select modem to cellular line. Click next put in #777 to dial to Cricket, click next… User Name: [email protected] Password: cricket Domain: Leave Blank, click finish…under proxy settings, check these 2 boxes (this network connects to the internet, and this network uses a proxy server to connect to the internet) Proxy Server: wap.mycricket.com click advanced. The only thing with a value should be HTTP wap.mycricket.com:8080 the rest blank. Click ok and ok again, this ok should bring you back to the connections screen at the bottom click advanced. Click select networks. Under both drop downs select Cricket. Click Ok Go into Exceptions Click add new URL for each of the following settings you are going to need to click add new url again, these don’t all go under one “Add new URL” Block
*mms.mycricket.com/servlets/mms
*.mms.mycricket.com/servlets/mms
*mycricket.com/
*.mycricket.com/
*.mms.mycricket.com/
*mms.mycricket.com/
Then Soft Reset.
COPIED FROM http://forum.ppcgeeks.com/showthread.php?t=25859
no credit to myself
AHHH!!!! His reply makes better sense for your question then mine.
I bow to you oh gran masta!!!