Hi to all. I solve my problem. Change myself motherboard. I buy second hand hermes with no working keyboard for 100eu (latter I solve even this problems,bad contact on flat cable)) and change the motherboard to my spv m3100. It's stupid to say that I solve this with some software, it's was hardware
faulty (or maybe not???) and I am very happy, because I can use my hermes again.
Now I have a one, my "old" motherboard (hermes) who working like pda, wi-fi and bluetooth also working, but without gsm. If any wish to do some experiment I am here, waiting for instruction. Also, I add some picture from the phase of changing motherboard.
Information for "experimental" hermes:
HERM 200
IPL-1.04
SPL-2.30.Olipro
Rom version:Schap's 4.00
Rom Date: 10/15/07
Radio version: none
Protocol version: none
ExtROM version: 3.60.20070822
No cid, no imei, can't flash radio (stuck in 0%)
Can't flash OS which contains radio (stuck in 12-13%)
Regards for all on this forum.
Hi,
how are you?
do you know is it possible to replace just radiochip to fix our hermes??
How I see, in "home made" it's not possible, because we don't have a special equipment for that operation. Even if you have, but where you can found this famously radio chip? If you wont, I can open my "experimental" Hermes and make a picture of all chip and send to you, but I think that on ftp you have all manuals and pictures with the name of each part. I use this manuals to safely open my hermes and myself change the motherboard.
If I understand you, your hermes working like PDA, without gsm. Do you have a same problem, that devices turn off yourself and until soft reset they don't wont to wake up? Also phone function working very slowly, sometimes it's not possible to activate connection manager...etc
And if you agree, please to continuing disscusion on this thread. Thank's.
eraserbabyboy said:
If I understand you, your hermes working like PDA, without gsm. Do you have a same problem, that devices turn off yourself and until soft reset they don't wont to wake up? Also phone function working very slowly, sometimes it's not possible to activate connection manager...etc
And if you agree, please to continuing disscusion on this thread. Thank's.
Click to expand...
Click to collapse
yes,i have same problem(but when i downgraded it to wm5 it works better and faster!).and like you I still have hope that it's not a hardware problem and wish to find solution.next week I will send my PDA to a serviceman to know what is his idea (maybe it'll work).
hamed_ppc said:
yes,i have same problem(but when i downgraded it to wm5 it works better and faster!).and like you I still have hope that it's not a hardware problem and wish to find solution.next week I will send my PDA to a serviceman to know what is his idea (maybe it'll work).
Click to expand...
Click to collapse
OK, I will waiting, and good luck.
Don't forget to inform us what's say serviceman....
Ok , i've joind the club of "no gsm" 3 months ago . and i've tried many many roms and radios and still no luck .
but in one try i've succeeded in flashing the radio to 100% and the radio worked very well and that night was 5 in the morning i danced on the desk when i saw it . i just couldn't belive it . i called my hermes 20 times from another mobile to hear the defult stupid WM5 ring tone , i missed it really
any way i couldn't believe my eyes , so i tried to do a hard reset to check if the radio will stay or go , it just vanished and again back NO GSM . i was disappointed really .
here's the way it succeeded with me and i was gonna post it for every one else as a solution but it happened with me once , and now it wont pass 0% .
here we go .
1.flash you device with GM360 gold edition http://forum.xda-developers.com/showthread.php?t=329282 don't ask why just try it .
2.after the phone is flashed with gm360 and working ok with no radio or "no gsm" messege now you should flash your phone with your device manufacturer WM5 ROM .
3. to flash WM5 rom you need to follow mr.vanx guide for safe WM5 downgrade . http://www.mrvanx.org/cms/index.php?...27&Itemi d=26 here it is .
4. now after you've flashed WM5 successfully and your device is also working fine with it but still no radio or "no gsm" . you need to flash only radio to your device . no OS only the radio .
5. download this radio . http://forum.xda-developers.com/showthread.php?t=334697 and unrar it on some folder . and don't flash it yet to your device .
6 download Olipro RUUwraper 5.2 http://forum.xda-developers.com/showthread.php?t=298737 there u go.
7. now the files from step "5" which they are the radio 1.54 put the file ruuwrapper from step "6" in the same folder with them to start the radio upgrade using "RUUWrapper.exe" not "ROMUpgradeUt.exe" . when u run it you will have multiple choices , choose "Force Unsafe SSPL (not recommended)" . .
now the radio upgrade should go smoothly as it went for me the first time . after the radio upgrade is done u should be able to use ur radio fine .
now can some one take half the effort of me writing this long method and try it ? thanx for the feedback also .
good luck for all .
Click to expand...
Click to collapse
i guess it was my one last lucky chance , and i blew it up with hard reset .
anyway the only solution right now for no gsm is to change motherboard unfortunatley
Nudge!!! :S
I lost my Radio today, also the IMEI is gone.
This morning it was working and this afternoon it just stopped, tried a hard reset, still nothing. Just tried to flash 1.54, but that didn't work, now trying 1.51 and i see the progress bar, but it stays at 0%
I will leave it this way at my computer and come back later, but it looks the radiorom is broken
I can flash everything except the radiopart, i really seems broken, i've tried flashing with different SPL versions including 2.60 olipro en SSPL.
Also the phone seems to be a lot slower.
But prior to this all the phone did hang often for the last few weeks, so i guess it was already starting to breakdown
i also have a almost similar experience, can anyone verify that the phone is already breaking down??
trion said:
I can flash everything except the radiopart, i really seems broken, i've tried flashing with different SPL versions including 2.60 olipro en SSPL.
Also the phone seems to be a lot slower.
But prior to this all the phone did hang often for the last few weeks, so i guess it was already starting to breakdown
Click to expand...
Click to collapse
chicharon said:
i also have a almost similar experience, can anyone verify that the phone is already breaking down??
Click to expand...
Click to collapse
What exactly is your problem? I've been noticing that about 70% of my calls fail or hang when I attempt to dial, when I try again they usually go through. I also have problems sending txt messages very often. Is my phone on its way out? I haven't even had this phone for a year.....pisses me off
eagercrow said:
What exactly is your problem? I've been noticing that about 70% of my calls fail or hang when I attempt to dial, when I try again they usually go through. I also have problems sending txt messages very often. Is my phone on its way out? U haven't even had this phone for a year.....pisses me off
Click to expand...
Click to collapse
My phone started to hang a lot last week, just for a minute and then come back again, also losing the phone connection. First i thought it was some software i installed. New rom, problem stayed the same.
And then yesterday i totaly lost the radio part, can't flash it in any way, but the phone still seems a lot slower then normal, like it's still looking for the phone part or something
I gues it's just broken, and as it is older then a year, i gues it is really trashed.....
So i think i'm gona buy a new accu for my old phone, my abbo ends in aug 2008, so no new phone before then
Related
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
RaDeNRFX said:
- I am so sorry posting this twice in the wrong sections, it seems that i'm a really noobie forum user - But i finally found the rite section. So my humble excuses.
All rite here we go, in advanced i thank u guys for trying to help me out here.
First, i'm a n00bie compared with the most of u guys.
My Device:
Tytn Herm 300
OS: Schaps Purple 3.30c
SPL: Hard-Spl 2.10 oli
Radio: 1.16.00.00 !Hmzz...that's the problem!
My phone functionallity sucks...some how it keep loosing connection while i see the phone indication bar up to 3 bars. So i decided to do something about it.
Beeing a noob i thought it got to do something with the OS. So i upgrade it to Schaps's wonderfull purple WM6 Hermes 3.30c and loaded the Hard SPL 2.10 oil V7. All went great, and my Hermes never looked so cool before.
But now i'm trying to upgrade my radio, which is still version 1.16.00.00, to what ever better version. I tried every radio upgrade possible from this list:
http://wiki.xda-developers.com/index...actedRadioRoms
Every single one starts well. passed the information retrieving from my phone. Confirmed the update, and then there was the installation progress bar....
All versions of the radio roms i downloaden get stuck in here. It doesn't even start..0% and error... And really i dun have any idea why.
So after re-flashing a gazillion times, i decided to ask help to the allmighty XDA community. So pls, if anybody there got a suggestion or the solution...i would be so thankfull and will slaughter a goat to worship you
Click to expand...
Click to collapse
ach2 said:
If you've got schaps Rom and HardSPL on your phone then you obviously don't have problems flashing or with PC/phone comms.
When you try flashing the radio, how long do you wait before deciding it doesn't work? I've found that some of them can take what seems like a really long time and I'm tempted to unplug and start again.
Maybe try again, then go make yourself a cup of tee/coffee or get a beer then come back 10 minutes later. If the upgrade still hasn't worked we'll have to look a bit deeper
Click to expand...
Click to collapse
I waited till the Program says connection error...and send me to recovery proces. And i've been making hella tons of coffee after trying to flash that many Radio Roms. Any other suggestions? I'm so desperate
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
ach2 said:
Ok, maybe some more info...
Do you see 'NO GSM' during the phone boot process?
Do you have no radio at all or just intermittent reception?
Are you running Vista?
What is the connection error number?
If you've lost the radio but have hard SPL it may just be a case of re-flashing an original manufacturers ROM (which will include the radio) then start your upgrading again afterwards. Don't forget to back-up data before flashing.
If you do flash a manufacturers shipped rom - check that you still have HardSPL afterwards.
Click to expand...
Click to collapse
Well the weird part is "No GSM" appeared occasionally...some times it shows it sometimes it's not showing it.
No...i'm a Vista hater. And dun have the original manufacturers ROM. I've got the "T-Mobile Vario II" from The Netherlands..so if anybody got a link for the original version i'd be thankfull.
The Radio it self is intermittent and very inpredictable...for example:
Radio indicator says i got full recieve:...but i can't call or recieve any.
Connection error: 262 (which is, if i'm not mistake a connection error.) Which is bull cuz i'm re-running every other ROM's upload with the same way and succeded/
Radio indicator says no reception and shows an exclamation mark:...and my GF just called me to hurry up and pick her up :/
But the weird part is...it seems that my radio ROM is locked somehow. I can upgrade or downgrade SPL's and OS ROM's but not the Radio ROM.
I've tried to use MTTY by now and followed the manual bellow: (Problem 5)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
But it began with invalid password. Procede as written and it didn't helped.
More suggestions are welcome
My bad...i didn't looked well enough. It is saying No GSM the whole time.
More information:
I've checked the Device information on the Hermes now some information are blank:
Radio: Blank
Protocol version: Blank
IMEI: Blank
All other information field are filled. Been spending hours reading tutorials and manuals...and nothing. HELP!
OK,
This isn't a problem I've had myself, but loads of other people have and there are quite a few threads on how to unbrick from here... you're going to have to do a bit of reading.
This page shows the different combinations of OS/radio/brick type etc and should point you in the right direction for the correct course of action http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Then read through this thread http://forum.xda-developers.com/showthread.php?t=286755 . It's got really long but read the beginning where POF describes the types of problem and also the solutions. Then it's probably best to jump to somewhere near the end and pick someone who has a similar problem.
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
ach2 said:
It sounds to me as though you need to just flash a radio in nbh format, but please do some more reading before you do this to check my advice - as I said at the beginning, I haven't had this problem so I'm only giving advice from what others have written.
Click to expand...
Click to collapse
I am really thankfull of ur post. Unfortunately, i've been doing some reading. Including the link u gave me. The problem is that i can't upload/flash Radio in nhb format.
As i described in the first place, i can't load a nhb format radio in RUUWrapper.exe properly. It can start the proces..but it always end up with a connection error code 260/262 during the installation progres bar (0%).
The solutions some ppl tried in ur link is often not my case. And the similar cases i have tried where i end up with the same grumpfy situation.
have you tried to flash the radio using the SD card method? I too have a cable connection problem but I fear mine may be hardware failure.
Yap...and no luck
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Hi,
i have one bricked Hermes,and I've tried all the methods that i read ever and i explained completely here:http://forum.xda-developers.com/showpost.php?p=1571302&postcount=1548 but no result.
yesterday i tried SD method with wm6 ROM that i downloaded from htc sit ,but i had this on my screen:
HERMIMG.nbh-
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM -
OS -
Update In Progress...
it freezes at GSM!!i waited 45min,but nothing changed,then i take out the battery.
do you know why?and what can i do?
sorry for my bad English.
hamed_ppc said:
Hi,
i have one bricked Hermes,and I've tried all the methods that i read ever and i explained completely here:http://forum.xda-developers.com/showpost.php?p=1571302&postcount=1548 but no result.
yesterday i tried SD method with wm6 ROM that i downloaded from htc sit ,but i had this on my screen:
HERMIMG.nbh-
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM -
OS -
Update In Progress...
it freezes at GSM!!i waited 45min,but nothing changed,then i take out the battery.
do you know why?and what can i do?
sorry for my bad English.
Click to expand...
Click to collapse
Hi I have the same problem, radio refuse to flash, something wrong with my radio chip, I have a OS but no gsm. "Welcome to the club" But, I don't know how to solve that problem.
eraserbabyboy said:
Hi I have the same problem, radio refuse to flash, something wrong with my radio chip, I have a OS but no gsm. "Welcome to the club" But, I don't know how to solve that problem.
Click to expand...
Click to collapse
ok,we can continue this thread to find the solution,is there anybody knows how we can fix this problem??
is it a hardware problem??i wish it isn't.
hamed_ppc said:
ok,we can continue this thread to find the solution,is there anybody knows how we can fix this problem??
is it a hardware problem??i wish it isn't.
Click to expand...
Click to collapse
I think that is hardware problem. I flash only OS, without radio and now my hermes work only as PDA, wi-fi and BT also work, but still no gsm.
eraserbabyboy said:
I think that is hardware problem. I flash only OS, without radio and now my hermes work only as PDA, wi-fi and BT also work, but still no gsm.
Click to expand...
Click to collapse
ok,but how we can fix it?Should we replace something in our pda??
i want to know is it fixable or not??
hamed_ppc said:
ok,but how we can fix it?Should we replace something in our pda??
i want to know is it fixable or not??
Click to expand...
Click to collapse
I don't know. In my country I have a htc services and they say to me that my motherboard must be replaced because is to hard to change only radio chip and they only change all motherboard. For 350 Eur(+some Eur) I can by new Tytn. Now I use my pda in my home (in toalet) via wireles to look internet. Work's fine, but sometimes freeze OS and I must do soft reset.
ok guys , i might found a temp solution or maybe it will work permenantely with some one , but i need some one who have spare time and steel nerves coz i'm sick and tired of trying many files and roms and radios .
so any one is willing to start this experiment with his hermes and his spare-time lets begin .
first of all i want to declare that this method revived my radio and i used my device for one day just fine receiving and making calls . then the next day i decided to make a hard reset to see if the radio will stay working , and the result was the radio was dead .
here we go .
1.flash you device with GM360 gold edition http://forum.xda-developers.com/showthread.php?t=329282 don't ask why just try it .
2.after the phone is flashed with gm360 and working ok with no radio or "no gsm" messege now you should flash your phone with your device manufacturer WM5 ROM .
3. to flash WM5 rom you need to follow mr.vanx guide for safe WM5 downgrade . http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=27&Itemid=26 here it is .
4. now after you've flashed WM5 successfully and your device is also working fine with it but still no radio or "no gsm" . you need to flash only radio to your device . no OS only the radio .
5. download this radio . http://forum.xda-developers.com/showthread.php?t=334697 and unrar it on some folder . and don't flash it yet to your device .
6 download Olipro RUUwraper 5.2 http://forum.xda-developers.com/showthread.php?t=298737 there u go.
7. now the files from step "5" which they are the radio 1.54 put the file ruuwrapper from step "6" in the same folder with them to start the radio upgrade using "RUUWrapper.exe" not "ROMUpgradeUt.exe" . when u run it you will have multiple choices , choose "Force Unsafe SSPL (not recommended)" . .
now the radio upgrade should go smoothly as it went for me the first time . after the radio upgrade is done u should be able to use ur radio fine .
now can some one take half the effort of me writing this long method and try it ? thanx for the feedback also .
good luck for all .
feedback
Just now I finished all, by your instruction, step by step. When do the last step, flashing radio rom it's stuck on 0%. Many thank's for help, but it does not work for me.
a-h-t1,
thx for your discription,I'll try your method as soon as i can(because ADSL isn't much available!!)
eraserbabyboy,
can you tell me when did this problem happen to you(i mean loosing GSM)??did it happen when you was flashing WM6 ROM??
I really want to know why this problem happen to me while i didn't have it before flashing??is flashing cause to a hardware problem???
eraserbabyboy,
can you tell me when did this problem happen to you(i mean loosing GSM)??did it happen when you was flashing WM6 ROM??
I really want to know why this problem happen to me while i didn't have it before flashing??is flashing cause to a hardware problem???[/QUOTE]
Hamed I dont know what's happened with my hermes, because I get him with the no gsm error. I have a bootloader 1.09 with enable kitl mode. In PB I lose many, many night to boot os but without sucess. And post many question here, but without answer, a-h-t1 is the first men who try to help and meny 10x for that.
So, before 2 week I send my hermes to Imei-check and before few days I get it back with bootloader 1.01 mfg and instruction from imei teamroblem_Description: The radio chip is faulty 100%. Now the handset is usable as PDA only (wifi + bluetooth working too), but not as a phone (the GSM module refuse to answer/flash).
DO NOT attempt to upgrade the firmware in the phone with a firmware which has RADIO upgrade, as it will put the handset back to the brick mode!!!
Model is SVP3100.[/COLOR][/COLOR]
After that I put the SPL 2.30 Olipro to prevent any future damage, and continuing to "play" and experiment, because I don't have more than, to loose. I have P3300 who work's very nice....
It's possible to boot any OS without radio. (I use nbh tool 1.01 to extract nbh file to nb and after make Ruu_signed but without radio).Also try metod via SD card and same to you, stop when try to flash radio. Also it's happened on 12-13%(independed of the rom version) when start full RUU upgrade. And when try to flashing only radio they stop on 0%. On 12-13% ruu upgrade try to flash radio in this moment, and this is the end. I am not sure is this hardware problems, but imei (I dont belived too much) said YES. In win OS I don't have a imei identification (in device info/identity) and of course radio version is blank. Sometimes happened that os blocked(freeze) or device just totaly go to power off mode and I must to do soft reset. Is any way to totaly disabled phone function in registry? I mean that freeze when phone try to find network or sim, but I am not shure. Last night I open my devices, and get out motherboard, just to see this famously radio chip. It's not possible in "home made" to change yourself this chip. Only if I have a more lucky and found some broken hermes with ok motherboard for 100-150 eur...
I hope that my info just little help to you to know "mystery" about our problems.
And one more time 10x to a-h-t1!
eraserbabyboy said:
Just now I finished all, by your instruction, step by step. When do the last step, flashing radio rom it's stuck on 0%. Many thank's for help, but it does not work for me.
Click to expand...
Click to collapse
I just tried it and same result like you
but many thx for a-h-t1 and eraserbabyboy's help.now I want to try fix it in hardware way!!
but if anyone has idea about our problem please say here.i think it's going to be common problem,because i see many people in xda who has the same problem.
Read this, to see how I solve my problem. But I still have a hope, that it's not hardware problem and in the future I hope that someone will found software key to solve our corrupted radio.
http://forum.xda-developers.com/showthread.php?t=338413
ok,i think it was almost three months ago that i had posted my last post!!
you know my problem and i feel it has became a common problem for poeple who have hermes,unfortunately.
last week,i found a service man who believed that my phone's problem is fixable.
so i gave my pda to him,and because he lives in another city,i returned to mine and waited for him.
yesterday i phoned him,and this is what he said to me:
"first,I tried software methods,but the result was nothing!then I disassembled the device and changed the piece of RF of your ppc.it hung first,but now it loads the windows and find the antenna too!!but immediatly after finding,it hangs."
he has used the Dopod's RF in my htc TyTN and thinks that this problem(hanging after finding the antenna) is because of not matched radiorom.
I have good feel about his say,and i'm trying to help him find the correct radio rom,because he is so busy and cant search the internet to find the radiorom.so I've mailed him the link of wiki's radio rom for hermes and I hope someday this tragedy will finish but i'm not sure.
if anyone have comment about this case please help us,specialy about the RF,because I don't know anything about the Radio Frequency.
I HAD the EXACT same problem I Hermes would get stuck at 11% EVERYtime I tried to flash the OS rom with WM6!! The upgrade process would start and then [email protected]! 11% and I would get ERROR 262 (loss of communication) No FIX anywhere, even with site full of "supposed Hermes Fanboys" Nothing NOBODY knows nothing bout this issue. BUT I think I have found a fix (I have recovered twice gonna do it 1 more time to confirm METHOD)
1a
Its called a 1a brick. Look in the sticky brick section. like 170+ pages of this issue. I believe I have the same device. No GSM/ no imei no radio. Can flash rom's all day long, as long as rom doesnt include GSM. Try to flash ANY GSM does nothing, let it sit 10hrs... Nice free PDA, till i can figure out the wiki & there must be hope for me. Till then my wiz100 keeps rocking. Like the 8525, but wanted it more as a phone then just pda.
nicknowsky said:
I HAD the EXACT same problem I Hermes would get stuck at 11% EVERYtime I tried to flash the OS rom with WM6!! The upgrade process would start and then [email protected]! 11% and I would get ERROR 262 (loss of communication) No FIX anywhere, even with site full of "supposed Hermes Fanboys" Nothing NOBODY knows nothing bout this issue. BUT I think I have found a fix (I have recovered twice gonna do it 1 more time to confirm METHOD)
Click to expand...
Click to collapse
I hope you will fix your device,but when I read about your solution,I felt that guy who brought back to life your device,has just used a ROM whitout GSM,the way that we have been using since months ago.if I'm in mistake so tell us more.
The end of the Tragedy
o0o0k!!
as I've said in my post,the service man that I love! replaced the RF of my pda,but new problem was hanging after finding the antena!!
as he told me yesterday,he tried another used RF,but this time the TyTN's one and it worked) and there is no problem.so after 4 months nearly I can use my pda.
as soon as I can,I will go to get my device and test it myself.
be wait for my smooth experience!!
What is this???
replaced the RF of my pda
Andrey_ORIN said:
What is this???
replaced the RF of my pda
Click to expand...
Click to collapse
its full name is RFSP=Radio Frequency Signal Processor.it's one of ICs on your Hermes mainboard.it needs a professional to replace.I'll explain more early.
but if you have same problem and have tried all of the the wiki methods then you can test my solution.
Helo everyone, im currently in limbo about what to do..
i've been using the official HTC WM6 rom on my 8525 with radio v1.40 i think.. i've been loosing signal 2 to times daily. I upgraded to Radio 1.57, everything worked much better then 48 hours later the radio went dead.
i've been using 2 different WinXP PCs but both have the same results so im sure its not the OS..
I've been reinstalling different OS without any problems but always reports NO GSM, i've tried running SSPL-HERM from within WM6 and run the flash from the radio 1.54.07.00 firmware here on XDA-Dev but still 0% progress on the "updating the rom".. error 262 update error..
The phone is using HRM100 IPL-1.04 SPL-2.10.Olipro
Could it be:
A - bad block? if yes, how do i fix it?
B - phone is bricked?
C - damaged radio (physical hardware)
Any help would be great!
I have EXACTLY the same problem....! Now I am worried that I'll get busted on the Warantee rap despite it being the offical T-Mobile release for WM6 for HERM300! Mine stopped working after 12 hours. I have a HERM300 and cannot flash the Radio back. Be careful... I think it's a bad block or something permanent. Trying to flash it back to WM5 and send it back for repair bit it's not looking so good at the moment. Will help you if / when I can.
Seems like all radio's starting to break
I didn't even flash mine and it is broken, can flash everything except for the radio part.
now using it like a normal PDA, using internet through bluetooth with my old phone.
Just 10 months to go before I can get a new phone, I don't think it will be HTC again, never got support from them, only from this website.
i found the best way to flash is by using the sd card method, I always use this method to flash my vario II
indie said:
i found the best way to flash is by using the sd card method, I always use this method to flash my vario II
Click to expand...
Click to collapse
tried it, but freezes at like 10%, how do i go about repairing bad blocks?
i tried the SD card method, no good.. i checked the unit, no bad blocks =(
How did you check for bad blocks? Wanna do the same for mine. Cheers.
Try to use an earlyer RUUwrapper after exctract the .exe file. It solved my same problem. I tryed to flash Schaps 4.00 and stoped at 0% I extracted the 4.00 and the 3.60 roms and I overwrited the 4.00's ruuwrapper with 3.60's ruuwrapper and I launched it (4.00) I can flash with that ruuwrapper without problems I hope it works to you too
mine JasJam (shaps 3.54b) gives the same problem.no gsm signal and after try to upgrade radio,it stuck at 0% and now is always at the 3 colour screen also after off-on battery...what can I do..please Help me!!!!!!
mickscores said:
mine JasJam (shaps 3.54b) gives the same problem.no gsm signal and after try to upgrade radio,it stuck at 0% and now is always at the 3 colour screen also after off-on battery...what can I do..please Help me!!!!!!
Click to expand...
Click to collapse
I think your problem is bigger, because if you haven't got gsm signal than maybe your Hermes has bricked...
that means that I will never fix anymore my hermes????
mickscores said:
that means that I will never fix anymore my hermes????
Click to expand...
Click to collapse
I think you can unbick you hermes, but i don't know how exactly... I should read a lot here and ask befor do anything:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Have you ever dumpeb your ROM? Because if you have the dll-s befor brick than, if I know well, somebody can solve the problem with a service cable...
GorTen said:
I think you can unbick you hermes, but i don't know how exactly... I should read a lot here and ask befor do anything:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Have you ever dumpeb your ROM? Because if you have the dll-s befor brick than, if I know well, somebody can solve the problem with a service cable...
Click to expand...
Click to collapse
Is it me or are suddenly lot's of TYTN's losing their radio en IMEI, i lost mine too now it is just like a pda, using my old phone with bluetooth for internet. Impossible to flash the radio. Os only works fine.
Yep! Dunno why. GSM appears to be dying, Just got mine repaired in the post from T-Mobile. Just did a quick MTTY check on it (info 8) and there is BAD BLOCK on it already!!! Repaired???? Not so sure. Should I risk HARD-SPL and flash the rom from WM5 to WM6?
Hi,
im currently running the following setup:
phoenix 2.51
radio 1.71
hard spl 1.22
with o2 as service provider in germany.
since some flashing and testing i discovered that after a few seconds of speaking i get massive interferences in the call. my calling partner cant understand me, but i can hear him.
i already flashed back to 6.1 wwe official rom but the error still persists.
does anybody have ideas which could help me?
RsRichard said:
Hi,
im currently running the following setup:
phoenix 2.51
radio 1.71
hard spl 1.22
with o2 as service provider in germany.
since some flashing and testing i discovered that after a few seconds of speaking i get massive interferences in the call. my calling partner cant understand me, but i can hear him.
i already flashed back to 6.1 wwe official rom but the error still persists.
does anybody have ideas which could help me?
Click to expand...
Click to collapse
Try a different radio, eg 1.65.28.25. Works very well, and low power consumption to boot.
use other radio rom
I had the same problem.
Many noises, people on the other side couldn't hear me as well as dropping line.
I also tried different combination in spl/rom/radio (also restoring original spl/rom/radio).
I solved by sending phone to service reparing (warranty).
I don't know exactly what they did since ther was no physical repair but they said they only upgraded something (which sounds strange to me since ther's no official upgrade for my country from HTC) but now it works fine.
shinji_73 said:
I solved by sending phone to service reparing (warranty).
I don't know exactly what they did since ther was no physical repair but they said they only upgraded something (which sounds strange to me since ther's no official upgrade for my country from HTC) but now it works fine.
Click to expand...
Click to collapse
So, what's the build number of ROM and also radio number? If it is one not on the board, any chance of dumping the ROM and posting it?
i tried with 1.5xx roms, 1.65.28.25 etc. and still have the problem.....
rling said:
So, what's the build number of ROM and also radio number? If it is one not on the board, any chance of dumping the ROM and posting it?
Click to expand...
Click to collapse
Rom version: 1.31.408.09
Date rom: 10/30/07
Radio version: 1.58.16.27
Protocol version: 25.61.30.03W
It seems to be the "standard" configuration...
But now on the splash screen there's no more "Niki pro" trace...D 1.31 as it used to be.
ok... i again tried several configurations and also flashed the complete original rom. the error still is there what can i do now? is there any possibility to format the whole phone except the bootloader?
heeeeeeeeeeeeeeeeeeeeeeellllllllppppppppppp
RsRichard said:
ok... i again tried several configurations and also flashed the complete original rom. the error still is there what can i do now? is there any possibility to format the whole phone except the bootloader?
Click to expand...
Click to collapse
The radio, SPL and ROM cover the entire phone's OS. The official HTC WWE release 2.09.405.1 has all three in it. Disable the Hardspl (if other than HardSPL 1.22) by flashing the sspl, then flash this ROM. This will return the phone to original state. You might need to do this if you need to send the phone back for warranty service.
I'm going to send my phone to service again because I got my problems back...because I definetly think I got some "hardware" problems...
If I shake my phone some metallic noises can be heard inside, did you try something similar?
any news on this topic? i still cant use my niki.... im still receiving massive intereferences when calling since my flashing orgy. how to put it back to a fully OEM state without any mods?
nothing? will i really have to send my phone to the service ..... please not, i damaged one of the guarantee seels (back of the phone, right to the camera) mit the pen once....
RsRichard said:
nothing? will i really have to send my phone to the service ..... please not, i damaged one of the guarantee seels (back of the phone, right to the camera) mit the pen once....
Click to expand...
Click to collapse
it must be radio issue - please try to flash a complete rom+radio, flash from microSD this time, rename the nbh file to NIKEIMG.nbh, enter bootloader and flash.
*push* still not working