Related
my first post and contribution.. hopefully it would be alot of help to other people..
this is the official IMATE 1.72 ROM...except that it was encoded to work with O2 XDA2 units
added the O2 splash screen to retain the O2 bootup image -just load O2.cab into your XDA2
the upgrade utility shouldnt show you any more country ID error for O2 XDA2 units.. if there are problems.. holler me ASAP!!
feedbacks would be nice, coz i would like to make upgrades for other Network providers as well..
Thanks for that.
Can you show me a step by step guide on how to upgrade O2 xda 2 1.60.WWE version to this?
Thanks again.
ok... im not an expert yet, coz i just had my XDA2 for a week, but i do enjoy tweaking and playing with it.. besides, the knowledge i gain thru reading this forum is more than enough..
ok.. here goes..
1. create a full BACKUP your XDA2.. (but i dunno if this is helpful should you fail to upgrade your ROM)
2. download the above file and extract it.
3. you should see it extract 7 files.
4. put your xda2 in the cradle connected to the PC
5. run HimaUpgradeUt.exe
6. wait around 30-60 mins. then follow the procedure as shown on your computer. (a hard reset would be required)
7. after the upgrade is done, you should see the IMATE screen upon booting up (instead of the O2 bubble screen) if you wanne be extra sure, check your XDA2 version.if everything is ok, then you should have upgraded it correctly
8. if you want to revert to the old O2 splash screen during bootup, then copy O2.cab to your XDA2 and run it there. Do a soft reset, and voila, it should be back to the old O2 bootscreen.
I suggest that you contact your NETWORK PROVIDER because you will need to manually configure GPRS, MMS, and INTERNET settings on your xda2 after doing the upgrade.
WARNING: i wont be held responsible or liable for failed upgrade of your unit. Please understand that by agreeing to upgrade your XDA2, you are taking full responsibility of whatever untoward incidents that may occur to your XDA2. Flashing the rom might lead to DATA LOSS, SYSTEM MALFUNCTION, and even DEVICE MALFUNCTION.
but.. the rewards of upgrading it is sweet!
Many thanks for all of these description.
BTW, how do you feel the upgrade?
What you really get from this?
Can you share with us?
Thanks again.
Cheers mate.
i dunno, im just a week old newbie in using XDA2 :wink:
i just enjoy tweaking the XDA..so far, no problems here.
My xda2 currently is 1.66wwe. after upgrade to 1.72wwe, what's the different between it? anything increase? sorry because i'm a new bird
did a lil research.. so far, came to this...
The 1.72 ROM eliminates the majority of problems from the 1.66 ROM such as:
Increased battery drain
Device slows down
Bluetooth GPS devices don't work, even with Pocket Bluetooth Tools
Can it be downgraded back to O2 xda2 1.60WWE Rom?
Many thanks.
i doubt that it can be downgraded... i havent personally tried to downgrade my ROM to a lower version.. but there are other threads related to this, and they claim that when they tried downgrading their ROMS, their XDA2 died....
you can try searching for other topics if there are information about downgrading... .so far, i dont have any problems with my 1.72 ROM...
except that there is no running program application which enables me to switch off any running program in the background.. but i easily remedied it by downloading TASKMANAGER.... its quite the same with running programs...other than that, so far, so good.
Error 121 Language ID Error
Hi,
after running HimaUpgradeUt.exe I get the message:
Error 121 Language ID Error (N-2-1-0-1), the ROM image that you are trying to use is not designed to work with your Pocket PC.
I ran ERedit2003 Version 1.2.20 and opened the file ms_.nbf using the password 0x20040305. I saved the file with the different language settings WWE, ENG and GER. Always the problem remains the same.
My XDA2 currently has ROM 1.66.01GER.
Thanks for help.
try to change the operator name , too! or use other hymalaya upgrade files, from other roms!
Re: Error 121 Language ID Error
GentleMan said:
Hi,
after running HimaUpgradeUt.exe I get the message:
Error 121 Language ID Error (N-2-1-0-1), the ROM image that you are trying to use is not designed to work with your Pocket PC.
I ran ERedit2003 Version 1.2.20 and opened the file ms_.nbf using the password 0x20040305. I saved the file with the different language settings WWE, ENG and GER. Always the problem remains the same.
My XDA2 currently has ROM 1.66.01GER.
Thanks for help.
Click to expand...
Click to collapse
hi, i tried encoding with it again.. please download it, replace the other files and try if it still gives you errors or not. thanks... ill be waiting for your feedback
Re: Error 121 Language ID Error > Error 120
Waxx said:
hi, i tried encoding with it again.. please download it, replace the other files and try if it still gives you errors or not. thanks... ill be waiting for your feedback
Click to expand...
Click to collapse
Hi,
Thanks. But now I get the message:
Error 120 Language ID Error ( N-1-8-1-8 ), the ROM image that you are trying to use is not designed to work with your Pocket PC. I tried with settings O2 WWE, O2 GER and O2 ENG.
When specifying CDL instead of O2 the error code changes to Error 120 Language ID Error ( N-1-8-8-8 ).
So the problem remains the same
Thanks for help.
Help for beginners: upgrading O2 Xda II to ROM 1.72
New to Forum-sorry to be slow on the uptake. I am trying to undersand how to upgrade O2 Xda II (ExROM 160.50) to ROM 1.72 without losing the machine. Waxx says you need to reconfigure the ISP settings (I assume because they are lost in the upgrade). I cannot find O2 settings for GPRS Interenet and MMS on the net. Talking to O2 is a waste of time.
Does anyone have a step by step description that results in ROM 1.72/Radio 1.18 (or lower if 1.18 still in beta) working on O2 Xda II?
Has anyone reported doing it sucessfully. Have non recoverable failures been reported?
RamyG
Just copy the attached CAB file across to say, My Documents on your XDA, and run it via FileManager.
It will customise your O2 XDA II with all the correct settings.
Once it has done that (and you've tested it works), just uninstall the O2 Active bit and your settings will remain (well they did on mine)
BTW - I upgraded to the new ROM, and have had no problems at all ! Very sweet
Mark
Thnx Mark, just to make sure before I jump in: the steps are:
(1) upgrade to 1.72 using Waxx's attachement (is that the file you used?) (2) follow the procedure you described and I will get O2 customised Xda II (same as where I started) but with ROM1.72 and later Radio Stack. Right?
2 questions:
(a) are the GPRS setting for MOBILE WEB (post paid)
(b) what benefits should I expect from the upgrade? (other than the satisfaction that it succeeded, l if it works?
thnx
RamyG
Yep I used the attachment from Waxx ...
The procedure you mentioned is correct ... I did have a few heart stopping moments after the upgrade because (like you) I couldn't find the necessary settings for GPRS etc .. but the O2 cab file re-installs everything back to what it should be for the UK.
You are prompted to choose relevant settings - in this case you get a choice from either post-paid (MobileWeb) or PrePay ...
As for benefits, people are reporting better bluetooth support, and better battery life. Only upgraded mine yesterday, so can't comment on either yet !
HTH
Mark
Has anyone else had problems charging overnight with the ROM version?
Got Error 120: Country ID error N-8-1-1-1
Hi all,
I am new member here. I did upgrade to ROM 1.72WWE and seems working fine. Because the PDA is idle, I try to roll back to ROM 1.60.44 eng. and got the country id error N-8-1-1-1. I tried to set the regional to English (UK) and English (US) but failed. Any comment? My XDAII is bought from Asia-HK. Thanks a lot.
Chris
Mark thnx for your help. For all those undecided souls I can report that Waxx's ROM 172 upgrade works fine for O2 Xda II. (BTW: it takes 3 times as long to upgrade as they say it does - it's 30 min for each of ROM ExROM and Radio modules).
Mark, O2.cab did not work as exepcted for some reason. When I ran it, it simple created a text file with O2 network config info and did not actually configure the Xda II. The info was correct and a manual config worked first time. Puzzled, I ran the O2 cab again but from another directory. This time I got the O2 spiral (I may have gotten the network configed again I can't know as I had previously configured it manually . The upgrade did lose the O2 dialer screen and reverted to the iMATE one. This is trivial. the Net is full of free attractive skins. e.g http://sourceforge.net/projects/pocketpc-apps/
Mark Peters- I thank you again.
RamyG
Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!
Hi,
I have a v1605 (HT645 supplied in the UK) which I have SuperCID'd, then updated to the Tytn 1.35 ROM, downgraded to SPL 1.04 and then installed the 1.20 Radio upgrade.
I am very happy with this setup now and have found it much more reliable than the Vodafone ROM.
I have been playing around with different ROMs and each time I have to manually setup all the settings in Connections for MyISP GPRS/3G, WAP, and Business Email for Vodafone UK contract.
Whilst I can do this each time successfully, does anyone know where the settings can be easily installed from the original Vodap001 ROM for the v1605. I have looked through the extended rom for this and that sets up most of the MMS Messaging and 3G icon, etc but not the Connections settings.
Is there a .cab that does this or am I just going to have to keep typing in these settings every time I change a ROM?
I have searched but see most people entering the settings manually so I guess I am asking for something that is not possible ..... but don't ask, don't get..... or otherwise learn!
Thanks
John
I don't know, but probably the cab file for connection settings is installed in \windows\preautorun.txt
Thanks pof, makes sense now, just wish I had looked before I started upgrading the ROm. I naively thought it was part of the extended ROM cabs.
Does anyone still have a Vodafone v1605 with the UK vodafone ROm installed. If so, it would be a great help if some could post the contents of preconfig.txt or preutorun.txt from the Windows folder. Otherwise I'll just have to wait until I get 3 hrs to go back to the original ROM and then go forward again to the HTC one.
Thanks if anyone has the file(s) otherwise no problem and I'll just have to convince the wife that another 3 hrs messing with the phone is actually fun!
Thanks
John
Hello all,
I Eb'd an HTC wizard (cingular 8125) running Wizard Love/NBD WM 6.
On the load screen I get:
AKU 2.3;
IPL and SPL:2.25.0001;
radio:2.25.11;
rom: 6.0.0.0.
My carrier is Tmobile.
Question 1: If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I wanna update my rom and think that I am competent enough to do so but there is alot to learn and this is not my full time gig...right.
Question 2: So, if I am correct in Q1 I should be able to flash roms right?
However when I attempt to do so the RUU gives me [error 224]. Active sync and or WMDC says its connected. (I installed the AS drivers in WMDC)
Question 3: Where do I go from here?
Question 4: The wi-fi is currently not working will a new rom potentially clear this up?
Thanks in advance for the time and advice..
grazie
hmmmm,
Well,did you updated to NBD wm6 yourself ? and how did you updated ? which method you adopted ? SoftSPL or HardSPL ?
You say its SIM unlocked as it takes calls on the Tmobile network .Did you SIM unlocked with lokiwiz03a ?
yes ! a G4 can be SIM unlocked but it can not be CID unlocked,however,it can be upgraded to wm6 rom,but with method either 'SoftSPL' or 'HardSPL'.With your present ipl/spl 2.25.0001 and you say its NBD wm6 running,then it must have been upgraded through 'SoftSPL' method,as it uses patched ipl/spl and Cid unlocks the phone temporarily,but it never permanently CID unlocks the phone.But with 'HardSPL' ,it changes the ipl/spl to a patched ipl 2.21.0001 and spl 2.21 olip.So everytime you want to upgrade,you'll have to upgrade using 'SoftSPL' method.
could you elaborate a little more about this.
Cheers!
Hey thanks for the correspondence zabardast_1, I have been getting frustrated and I have many times contemplated going for the brick or bust approach here.
So, I have done none of the updating on this rig. I rec'd it and I wanted it primarily for wifi however I can't get the wifi card/ (sdiowlan I believe) to even recognize an AP (... I posted in the networking forum but no response.) Thus my own reasoning leads me to believe I should start from scratch with a new rom unless you know of something else.
So, I am not the most savvy and thought that all of the info I had led to SIM and CID unlocked. I just read otherwise last night and in your reply. The info I have provided is accurate the IPL, SPL, radio, although I don't know which NBD release it is; just says 6.0.0.0 and release date: 2/2/07.
I am trying to get the new rom on the my device however and I would've probably already bricked it if I could get an RUU to communicate with my wiz. I always get [Error 224] when I run it and my phone is connected through active sync. I am running vista but have installed the AS drivers for WMDC. I also tried it at work the other day with XP same situ. I then tried flashing from the bootloader screen with an NBD, Wizard Love ( w/ Italian installer?), and T-mob (226102_22610105_022511). The only one that says it will update is the Tmob ROM, however I got cold feet at the update button and canceled.
Other funny stuff I have observed that may or may not be related to the problems I am having are:
Can't install cab files ie (enable rapi or Cert SPCS) and Wiz Sys Tools couldn't read my CID block and hard_SPL G4 gives me REXX error ( SPL_Version has no value).
So, any wizdom you or anybody can drop is much appreciated and needed at this point.
Whew...
Listen carefully. G4 Wizard cannot be CID-unlocked without paying money. (And yes, you are using a G4).
What you need now is to Flash your original stock carrier ROM (Or wizard love) to get your OS back. Then either use SoftSPL or install HardSPL and flash WM6 ROM.
Thanks Starkwong,
I will try installing wizard love tomorrow at work and if that don't work I will attempt a Cing ROM (will all of these work or do I need to mind my G3's and G4's for these???)
Grazie
So, It worked using Wizard Love at work and out of the bootloader window. Now I need to:
1.) Get wifi working.
2.) Get a newer ROM
I put a post up in the networking thread, I am a tool so far as these devices are concerned so be easy on me.
http://forum.xda-developers.com/showthread.php?t=372811
So do I get the wifi issue resolved before I reflash???
Thx again
I don't know what you mean by "wifi not working".
Maybe it is the wifi AP doesn't allow 11Mbps (802.11b) connections?
However, going to any of the WM6 ROMs should already set the registry to allow Wizard connects to G-Only APs. Just use HardSPL/SoftSPL and flash a WM6 and you will see.
OK so "wifi not working" may indeed be a general statement...
What I mean to say is that I am not able to connect to any wireless networks for internet not home (Linksys WRT 54G v5 with ddwrt firmware) or school (university wide) or my city's wifi network. It won't even detect them at least none that Ive seen since I've rec'd this phone. So, that is what I meant by the ambiguous statement.
So, being as your last post was a success I will try as you say and post the results tomorrow. Thanks again starkwong!!!
1 quick thing however, to be sure, I can now try the hard spl or soft spl method of tricking my phone to run an upgrade to WM6?
Still not able to get wifi APs????
OK although I have been successful at reinstalling the Mfg ROM and then Hard SPL'ing my wizard thanks to ya'll I still am unable to connect to a wireless network (see one even). I have the Olip on my SPL and I installed a TNT version of WM6 and I am still at work (drunk but still here). Anyway I can't see my wireless AP and I am beginning to think its a hardware issue if thats possible, i dunno the dynamics of this system maybe thats why it was for sale. In any event as usual I am willing to try what ever you guys throw at me as you're my only hope obi wan. Alright Im gonna go home for the night and try getting on to my home network.
Thanks again for all the help guys.
Is your device a original one from phone operator? I suspect your device is a China Dopod 838 with replaced casing, because the China version has the wifi hardware removed, so wifi can't be started even if an English ROM is used.
Looks to be authentic 8125
Starkwong, the Cingular logo and the 8125 model # are on the phone case where they have been when I've seen them before in pics. Therfore, I dunno I guess it looks like every other 8125 I've seen. Can I check the SN, IME or anything to be sure?
Thanks Again!!!
Starkwong,
I am getting all the options for wifi on my phone the LHS LED flashes green when I enable it and alternates blue green when BT is enabled. So, could it still be that its a dupod? I dunno but I am going home for the night... Thanks for your help. I will try connecting to my home network when I get there.
I am trying to update to WM6 on my G4, evertime i use the update utilty tool and I get to the "verify that you want to update the ROM version" I cannot see the replacement rom,
what am I doing wrong?
I see:
Model ID wizard
model version 1.2.0.0
language english
to
model version wizard
image version (nothing its blank)
language WWE
any idea what I am doing wrong?
I have tried several Rom packs from here but get the same on all
Its not possible to upgrade to wm6 with a CID locked phone.Read and follow the SoftSPL or HardSPL method posted as stickies in the G4 sub-forum.
yep, i used the unlocker, after downloading the tutorial here i saw where I was going wrong, now have the new Rom updated and working well, except.......
No data or internet connection, all other functions work, bluetooth, wireless phone sms etc but cannot connect to internet or send recieve mail. just get "cannot connect with current connection settings" message. it used to be the 02 software, still running an the same 02 sim which works fine in my other phone, either I am missing something on settings for the new rom. using the Mfrazzz wm6 Rom
any ideas?
You need to set up the GPRS settings for your carrier,get them from O2 or check out this link:-
http://forum.xda-developers.com/showthread.php?t=299023