Related
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Ok well I had a unlocked 8125 and I stumbled across a new 8525 for 150, so I picked that up... Now I should be getting it tomorrow and my question is this...
I'm assuming I fall under the post April category(being brand new) with the difficult SIM unlocking procedure... Now I'm not really in to switching around my carrier, I have AT&T its a AT&T branded phone and I'm fine with that... the only thing I really care about is being able to flash different OS roms and whatnot.
So do I just run the auto unlocker and only select CID unlock??
I've been trying to read and find out if the auto unlocker CID option will still work for post April units but I haven't been able to find the response yet.
Or am I totally in left field on this??? Do I need both CID and SIM unlocked to do OS rom flashes??
I acquired the 8125 already unlocked and those tend to be easier to do stuff to than these, or I'm just not reading the right thread.
Any info is appreciated.
I will not be turning the unit on till I hear a response from you guys. Worse case I just wont let the customization complete.
BerettaFreak said:
Ok well I had a unlocked 8125 and I stumbled across a new 8525 for 150, so I picked that up... Now I should be getting it tomorrow and my question is this...
I'm assuming I fall under the post April category(being brand new) with the difficult SIM unlocking procedure... Now I'm not really in to switching around my carrier, I have AT&T its a AT&T branded phone and I'm fine with that... the only thing I really care about is being able to flash different OS roms and whatnot.
So do I just run the auto unlocker and only select CID unlock??
I've been trying to read and find out if the auto unlocker CID option will still work for post April units but I haven't been able to find the response yet.
Or am I totally in left field on this??? Do I need both CID and SIM unlocked to do OS rom flashes??
I acquired the 8125 already unlocked and those tend to be easier to do stuff to than these, or I'm just not reading the right thread.
Any info is appreciated.
I will not be turning the unit on till I hear a response from you guys. Worse case I just wont let the customization complete.
Click to expand...
Click to collapse
You only need to do CID for that purpose. You are correct. Of course, doing SIM won't hurt you, but you only NEED CID.
Ok so when I get this phone... turn it on, do touch screen thing, do other crap, and CANCEL the customization with a soft reboot??? and then I can sim unlock it?
What sim unlocker do I use and whats the best radio for my location? Phone will actually be delivered today so this is why I'm asking.
Wait I think I got it... Turn on phone... Reboot before customization...
Run AUTO_Unlock_v3a once connected, after 1.16 radio installed then run Herm_Unlock_v3.exe to unlock it and once that is done run SoftBank_1.33.761.4_Extrom to remove the bootloader update.exe and then I can hard reboot without problems...
That sound right? This is following POF's thread on how to unlock these... http://forum.xda-developers.com/showthread.php?t=301952
I just run olipro 2.10 hardspl v7 and then I can flash any rom and radio I wish.
Yes but mine is a post April release phone which aparently has a radio bootloader update to 0182 which then makes the Radio rom un updatable, or impossible to unlock the sim.
Unless I dont need the Sim unlocked to do radio updates... but the more I read leads me to believe I wont be able to update the radio if I let the 0182 radio bootloader update run.
OR unless I'm completely retarded and this doesnt apply to the AT&T 8525.... I cant really find that on here.
Either way I'M LOST!
Yeah I think I'm retarded and read too far into this... I don't think the AT&T 8525's have this Radio Bootloader update thingy thats coming on the SoftBank phones...
Well all is good... fired the phone up, used it for all of 20 min before I used the auto unlocker on it unlocked CID and SIM, and then flashed it with VP3G WM6 rom, and the newest 1.54 radio... all is good so far.
Ok, I think I'm still at 1.04 IPL and 1.40 SPL, Olipro, is it worth it for me to install the Hard SPL v7 update??
IPL and SPL stuff on these phones are slightly more confusing than on the older 8125's
Also how do you get to the 3 color boot loader screen manually?
I did a HTC WM6 flash, wasnt very impressed and went back to the vp3G setup... Also is the 1.54.07 radio any good... the HTC rom put me down to 1.48 and since the 1.54 takes 20 min to upload I may leave it as is right now.
BerettaFreak said:
Ok, I think I'm still at 1.04 IPL and 1.40 SPL, Olipro, is it worth it for me to install the Hard SPL v7 update??
IPL and SPL stuff on these phones are slightly more confusing than on the older 8125's
Also how do you get to the 3 color boot loader screen manually?
I did a HTC WM6 flash, wasnt very impressed and went back to the vp3G setup... Also is the 1.54.07 radio any good... the HTC rom put me down to 1.48 and since the 1.54 takes 20 min to upload I may leave it as is right now.
Click to expand...
Click to collapse
I would update to the latest HardSPLv7. Oli makes it better every time - more protection.
1.54 is an AT&T release, so it is probably better than 1.48. I think 1.50 was also an AT&T release, but you can use it and see if it works. The biggest difference usually seems to be battery.
Regarding putting into bootloader screen, I don't have my phone on front of me, but I am sure it is in the wiki. It is a right side button, a left side button and the press the reset hole on the bottom. I think it is the bottom side buttons - OK, PTT and the reset hole. (I think)
Hello all,
I Eb'd an HTC wizard (cingular 8125) running Wizard Love/NBD WM 6.
On the load screen I get:
AKU 2.3;
IPL and SPL:2.25.0001;
radio:2.25.11;
rom: 6.0.0.0.
My carrier is Tmobile.
Question 1: If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I wanna update my rom and think that I am competent enough to do so but there is alot to learn and this is not my full time gig...right.
Question 2: So, if I am correct in Q1 I should be able to flash roms right?
However when I attempt to do so the RUU gives me [error 224]. Active sync and or WMDC says its connected. (I installed the AS drivers in WMDC)
Question 3: Where do I go from here?
Question 4: The wi-fi is currently not working will a new rom potentially clear this up?
Thanks in advance for the time and advice..
grazie
hmmmm,
Well,did you updated to NBD wm6 yourself ? and how did you updated ? which method you adopted ? SoftSPL or HardSPL ?
You say its SIM unlocked as it takes calls on the Tmobile network .Did you SIM unlocked with lokiwiz03a ?
yes ! a G4 can be SIM unlocked but it can not be CID unlocked,however,it can be upgraded to wm6 rom,but with method either 'SoftSPL' or 'HardSPL'.With your present ipl/spl 2.25.0001 and you say its NBD wm6 running,then it must have been upgraded through 'SoftSPL' method,as it uses patched ipl/spl and Cid unlocks the phone temporarily,but it never permanently CID unlocks the phone.But with 'HardSPL' ,it changes the ipl/spl to a patched ipl 2.21.0001 and spl 2.21 olip.So everytime you want to upgrade,you'll have to upgrade using 'SoftSPL' method.
could you elaborate a little more about this.
Cheers!
Hey thanks for the correspondence zabardast_1, I have been getting frustrated and I have many times contemplated going for the brick or bust approach here.
So, I have done none of the updating on this rig. I rec'd it and I wanted it primarily for wifi however I can't get the wifi card/ (sdiowlan I believe) to even recognize an AP (... I posted in the networking forum but no response.) Thus my own reasoning leads me to believe I should start from scratch with a new rom unless you know of something else.
So, I am not the most savvy and thought that all of the info I had led to SIM and CID unlocked. I just read otherwise last night and in your reply. The info I have provided is accurate the IPL, SPL, radio, although I don't know which NBD release it is; just says 6.0.0.0 and release date: 2/2/07.
I am trying to get the new rom on the my device however and I would've probably already bricked it if I could get an RUU to communicate with my wiz. I always get [Error 224] when I run it and my phone is connected through active sync. I am running vista but have installed the AS drivers for WMDC. I also tried it at work the other day with XP same situ. I then tried flashing from the bootloader screen with an NBD, Wizard Love ( w/ Italian installer?), and T-mob (226102_22610105_022511). The only one that says it will update is the Tmob ROM, however I got cold feet at the update button and canceled.
Other funny stuff I have observed that may or may not be related to the problems I am having are:
Can't install cab files ie (enable rapi or Cert SPCS) and Wiz Sys Tools couldn't read my CID block and hard_SPL G4 gives me REXX error ( SPL_Version has no value).
So, any wizdom you or anybody can drop is much appreciated and needed at this point.
Whew...
Listen carefully. G4 Wizard cannot be CID-unlocked without paying money. (And yes, you are using a G4).
What you need now is to Flash your original stock carrier ROM (Or wizard love) to get your OS back. Then either use SoftSPL or install HardSPL and flash WM6 ROM.
Thanks Starkwong,
I will try installing wizard love tomorrow at work and if that don't work I will attempt a Cing ROM (will all of these work or do I need to mind my G3's and G4's for these???)
Grazie
So, It worked using Wizard Love at work and out of the bootloader window. Now I need to:
1.) Get wifi working.
2.) Get a newer ROM
I put a post up in the networking thread, I am a tool so far as these devices are concerned so be easy on me.
http://forum.xda-developers.com/showthread.php?t=372811
So do I get the wifi issue resolved before I reflash???
Thx again
I don't know what you mean by "wifi not working".
Maybe it is the wifi AP doesn't allow 11Mbps (802.11b) connections?
However, going to any of the WM6 ROMs should already set the registry to allow Wizard connects to G-Only APs. Just use HardSPL/SoftSPL and flash a WM6 and you will see.
OK so "wifi not working" may indeed be a general statement...
What I mean to say is that I am not able to connect to any wireless networks for internet not home (Linksys WRT 54G v5 with ddwrt firmware) or school (university wide) or my city's wifi network. It won't even detect them at least none that Ive seen since I've rec'd this phone. So, that is what I meant by the ambiguous statement.
So, being as your last post was a success I will try as you say and post the results tomorrow. Thanks again starkwong!!!
1 quick thing however, to be sure, I can now try the hard spl or soft spl method of tricking my phone to run an upgrade to WM6?
Still not able to get wifi APs????
OK although I have been successful at reinstalling the Mfg ROM and then Hard SPL'ing my wizard thanks to ya'll I still am unable to connect to a wireless network (see one even). I have the Olip on my SPL and I installed a TNT version of WM6 and I am still at work (drunk but still here). Anyway I can't see my wireless AP and I am beginning to think its a hardware issue if thats possible, i dunno the dynamics of this system maybe thats why it was for sale. In any event as usual I am willing to try what ever you guys throw at me as you're my only hope obi wan. Alright Im gonna go home for the night and try getting on to my home network.
Thanks again for all the help guys.
Is your device a original one from phone operator? I suspect your device is a China Dopod 838 with replaced casing, because the China version has the wifi hardware removed, so wifi can't be started even if an English ROM is used.
Looks to be authentic 8125
Starkwong, the Cingular logo and the 8125 model # are on the phone case where they have been when I've seen them before in pics. Therfore, I dunno I guess it looks like every other 8125 I've seen. Can I check the SN, IME or anything to be sure?
Thanks Again!!!
Starkwong,
I am getting all the options for wifi on my phone the LHS LED flashes green when I enable it and alternates blue green when BT is enabled. So, could it still be that its a dupod? I dunno but I am going home for the night... Thanks for your help. I will try connecting to my home network when I get there.
Okay.. I got a brand new touch dual last week, and off course, it seems to be sim locked.. It IS nice and shiny though. A silver version actually..!
Anyways, I did try the SuperSID and security unlocker.. But i'm kinda stuck at one of the first steps in the manual.. Checking your original radio version and downloading it.. It seems my Niki has radio version 1.58.21.24.. And that isn't available for download.. Anywhere.. :')
So.. I've got this phone on my desk, which i can look at, but can't use.. All brand new, nice and shiny..
I've been searching the forum to see if there's any way to dump my original radio, biut i guess to achieve that, the phone needs to be unlocked on forehand, right..? Any suggestions on how to go about this?
You can try with another radio, like the 1.58.21.23S, but first of all, be sure that you have a NIKI100, not a Neon or similar.
Well, the battery says NIKI160. But fortunately for me, underneath the battery on the phone itself, it says NIKI100.
So, according to the Niki SuperCID thread i can just skip installing original radio (step 8) and flash v. 23s..? Without consequences..?
Hi xxxneoxxx!
I know it's a while ago you were wondering if you could use the .23 radio.. But I'm still curious if you have tried it! And if you did, how does the dual perform?
Thanks!
I had to do that either, one of the two niki100 had a 1.64 radio, and when doing "step 1", it always crashed at 99%. So whay I did was first downgrade the radio to a 1.56, then run step 1, and finally flash back to another radio (random one), it worked perfectly...
Just remember to use spl 1.15 or the unlocker won't give you results...
Duplicated post, sorry...
Hi biktor_gj!
I've already installed spl 1.15. So that's one step in the right direction =)
But how is it possible you can use different types of radio's without any problems? Because several threads warn you for the damage a wrong radio can cause...
Well, after a while of reading up, i kinda gave up on it.. Found all kinds of info, none mentioning this radio version.
So i figured; i saved over 150 euros buying it locked, why not pay something to get it unlocked in return. I mean, unlocking isn't that expensive after all.
One of the infos i found was actually that over here in the Netherlands, unlocking your phone using an unlock code doesn't void your warranty, but using software to do it, does. So this was an extra reason find an alternative way. Eventuelly bought an unlock code. Went over to www.htccode.com and bought an unlocking code over there. Works like a charm.
I know, it might be the easy way to out, and if my radio version was mentioned in the unlocking thread i would have been more sure of the fact it WAS actually going to work properly, without the battery draining and stuff, but it wasn't mentioned, so i figured i was better off playing safe on this one..
Dear XDA Developers community,
my father recently gave me his old HTC HD2. It had its factory default stuff. I wanted to download some apps and play around with it, so I downloaded some apps from the marketplace. As soon as I downloaded a free Sudoku game, and ran it, the phone stopped responding. I tried to do a soft reset, but the phone did not respond either (it was stuck at the menu).
Now, I may have done an error: I removed the battery, instead of performing a Hard Reset. When I turned it on, it started rebooting in a loop, being stuck always at the HTC white welcome screen.
I decided for a Hard Reset. Well, it always gets stuck at the bootloader screen (the screen with the 4 colors).
So, I researched a bit, and found out, you can return to its stock ROM, eve with a stuck bootloader.
Well, I downloaded many old ROMS (the Rom before the problems was a 1.66 one), and ran the RUU through USB. But it always gave me a Incorrect vendor ID error (I think it was 194), so the update would always stop at 1%.
I even tried a 1.43 ROM.
I tried many WWE version Roms, but they don't seem to work. My father bought the phone on Amazon US, with no special contract or phone lock, so I guess it has to be a WWE, so I don't know why the RUU says it's incorrect.
I have seen other threads that have some similarities, but my exact same problem has not been addressed.
I would be very happy if you could help me, since I do not want to spend any money on repairs which I could probably perform with help of the community
I would be most glad to give more information if needed.
Many thanks in advance.
Edit:
The issue was resolved by installing HSPL4 on it, and then using a WWE 1.66 ROM on it! Silly me for not trying that earlier!
glad you sorted it, , to explain why it wouldnt work, you were not using the correct rom for that phone.
Your first clue would be the 'invalid vendor id'. An 02 phone (for example) will only take o2 roms, a tmo phone tmo roms, a voda phone, voda roms. Only unbranded phones take pure wwe roms, so for example
ruu leo htc wwe 1.66.405.2
see it says HTC in the filename? its for unbranded (not sold by a network) hd2s only.
I guess you have a branded one. (even if its been unlocked, the rom lock always remains, which is why we have hspl)
Incidentally, you only had trouble because you initially flashed from sd card, and step 1 in teh sd card flash is hspl gets removed, the phone restarts to continue flashing but because hspl is now gone, it fails. Had you flashed from usb teh first time, it would have worked.
samsamuel said:
glad you sorted it, , to explain why it wouldnt work, you were not using the correct rom for that phone.
Your first clue would be the 'invalid vendor id'. An 02 phone (for example) will only take o2 roms, a tmo phone tmo roms, a voda phone, voda roms. Only unbranded phones take pure wwe roms, so for example
ruu leo htc wwe 1.66.405.2
see it says HTC in the filename? its for unbranded (not sold by a network) hd2s only.
I guess you have a branded one. (even if its been unlocked, the rom lock always remains, which is why we have hspl)
Incidentally, you only had trouble because you initially flashed from sd card, and step 1 in teh sd card flash is hspl gets removed, the phone restarts to continue flashing but because hspl is now gone, it fails. Had you flashed from usb teh first time, it would have worked.
Click to expand...
Click to collapse
Thanks for the answer Samuel. I got the phone to work again, and I even loaded NAND Android from the DFTeam.
Although the ROM runs just perfect and I love it, now my Volume Up key has stopped working.
I could not post on the Development section, so I guess I won't bother anyone, and will just post it in this thread.
It is a minor issue, but it's still is annoying. I found on the forums problems with the key with other models, but not with the HTC Leo.
Maybe someone has heard of this. Again, thanks in advance!