Prophet not upgraded just tri colour screen - JAMin, XDA Neo, S200 ROM Development

Hi there, I have just upgraded or should i say tried to upgrade to the new WM6 coffie ROM and the Krystal ROM but with both of these I can flash, however upon reboot it stays at the 3 colour screen
I have followed the Hard SPL guide for a G3 ---- Check
So what have I done? please someone help - it's a mates phone
also I tried to go back to the original WM5 from the FTP site, but it fails because I have updated the SPL, I would appreciate a link to a WM5 that doesn't check and that is in english........ if that would fix the problem
One last thing - i tried to use the update tools again but it says there is no device connected so I did a hard reset and tried again but no go, after a hard reset i can flash the other roms though
cheers all

No Panic !!
andytof47;1862521 said:
Hi there, I have just upgraded or should i say tried to upgrade to the new WM6 coffie ROM and the Krystal ROM but with both of these I can flash, however upon reboot it stays at the 3 colour screen
I have followed the Hard SPL guide for a G3 ---- Check
So what have I done? please someone help - it's a mates phone
also I tried to go back to the original WM5 from the FTP site, but it fails because I have updated the SPL, I would appreciate a link to a WM5 that doesn't check and that is in english........ if that would fix the problem
cheers all
Click to expand...
Click to collapse
No Panic~~~
Pls try to have a look to the link at my signature
( HardSPL easier)
please reply if ok!

I thought The sticky on top of the forum covered this
Hey there, would this be the problem? I thought Jumpspl was included in the initial upgrade tools folder?
Is this the same? and also does this problem (tri color screen) happen when it hasn't been properly flashed with the hard spl?
cheers

andytof47 said:
Hey there, would this be the problem? I thought Jumpspl was included in the initial upgrade tools folder?
Is this the same? and also does this problem (tri color screen) happen when it hasn't been properly flashed with the hard spl?
cheers
Click to expand...
Click to collapse
that is good and for experience users, mine is mostly for juniors. Please read and nothing bad.
The jumpspl... 100% work, and follow the steps, never fail.

Will your method work when not booting?
Just read your method and I hope to try it soon, but will your method work if it is not booting --- the method sounds like it needs the system to boot is this correct?
I hope it will work on this system while it is not booting...... I will let you know
OK I just read the whole post -------- The only file I can see is the jump spl.zip --
is that the hard spl or what?
dioxda2 I see how helpfull you are and thanks so far but how do I get the phone out of recovery mode or whatever mode that is??? what is the file I need??? please
thanks heaps

Related

WM6 upgrade gone awry!

Hi All,
I followed the "new" instructions for updating my Prophet to WM6, but now I'm stuck at the boot loader with this info showing:
IPL 1.00
SPL 2.13
Nothing else is displayed, except for the "USB" text at the bottom (which just indicates that it's connected via usb, right?)
I suspect that "HardSPL" step did not work correctly. But it seems that there's no way now to re-try that step, because I can no longer connected to ActiveSync.
If I just try re-flashing the new WM6 ROM, it seems to complete successfully, but I'm just returned to the boot loader again. Hard resetting does nothing.
Any ideas, advice on what to try next?
Thanks.
Ah.... If only I had searched a little bit further! I found these instructions here:
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
I've now completed that step, and my Prophet boots again. I'm now re-attempting the upgrade to WM6.
Phew! That did it. I've now successfully upgraded.
search & u will find.... the wiki has the answer...
congrats on upgrading btw....
Hi sinnerman,
I'm facing the exact same problem with my Imate JamIn. I tried everything, but it is still stuck on the tri color screen, could you please tell me which rom in the list you downloaded that fixed your problem?
Thanks.
wessamzeidan said:
Hi sinnerman,
I'm facing the exact same problem with my Imate JamIn. I tried everything, but it is still stuck on the tri color screen, could you please tell me which rom in the list you downloaded that fixed your problem?
Thanks.
Click to expand...
Click to collapse
just flash back to the original rom than use jumpspl to upgrade to the wm6 rom u like...that should be fixed ur problem.....
wessamzeidan said:
Hi sinnerman,
I'm facing the exact same problem with my Imate JamIn. I tried everything, but it is still stuck on the tri color screen, could you please tell me which rom in the list you downloaded that fixed your problem?
Thanks.
Click to expand...
Click to collapse
Sorry wessamzeidan, I don't remember which exact ROM I downloaded... I just followed the instructions from here:
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery

PLEASE HELP. IM A n00b at this and i think i bricked my G4 cingular 8125.

So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
dahdout said:
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
Click to expand...
Click to collapse
What IPL/SPL it displays now ? ,Does it get into Bootloaders ? if it still does than download and flash 'wizard_love_rom' hope it'll recover back.
RE:
It just boots into a white screen. If i hold the camera and power buttons together it boots into bootloader mode, and says USB in the bottom corner. (when i am conncected via usb) but the problem is that active sync doesnt recognize it in bootloader mode. I have tried flashing it in many different ways and i have had no success.
When i go home i will try wizard_love_rom.
and as for the IPL/SPL, i will also check that when i get home.
Where can i download the wizard_love_rom?
Thanks for the help !
RE:2
Hello,
Mr IPL and SPL are both 2.25.0001
My GSM: 02.25.11
My OS: 2.18.0.0
Good News
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
dahdout said:
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
Click to expand...
Click to collapse
Glade its working again !
You got a G4 device,it cannot be CID unlocked,but however,it can be upgraded to wm6 or 6.1,read the methods 'HardSPL' or 'SoftSPL' posted as stickies in the G4 forum for upgrading to wm6 or 6.1.
re:3
thanks, you really saved me with your help!
dahdout said:
thanks, you really saved me with your help!
Click to expand...
Click to collapse
Thanks !
Glade you got it working
sorry, but i need help... again
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
dahdout said:
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
Click to expand...
Click to collapse
ok,for error (300)you can use the RUU MUNS already posted in the 'HardSPL' thread,download the RUU_MUNS application extract it to a folder and copy and paste all the files of this extracted to the folder of the Rom replacing all the RUU files in that folder or copy the nk.nbf folder in the Rom to the extracted folder of the RUU_MUNS and then run the RUU,it will start to flash and complete and hopefully fully boot up.
For edge or gprs,you'll have to get network settings of your network carrier or check out the thread from where you downloaded the rom,its uaually posted there or check out the 'Network' thread.
Aquestion to Zabardast_1 ?
294 error , invalid vender ID
what does that means & asolution to it during rom update
ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.

How to flash Hard-SPL onto HERMES

Can anyone please post a guide on how to flash Hard-SPL onto my HTC TYTN.
The guide for installing Hard-SPL onto the HERMES is not available anymore, and i am EXTREMELY confused about what im doing, and i am afraid i will brick my phone if i do something wrong.
Please please please help!
Read the sticky, first post on this page.
It really isn't hard to do. But be sure you know what you are doing btw. SO read the sticky!
Basically you just download the flavor of Hard SPL you want (I used 2.10 which I can recommend, very easy to downgrade to factory SPL again as I just learned!).
After download unzip the folder and run the RUUWrapper. Follow instructions exactly, do nout unplug your device etc. and it should work like a charm. It takes about 1 minute!
If you don't know what you are doing or you are still doubting, wait for Mr Vanx site to come online again or don't flash. There is always a risk you screw up and end with a $500 brick.
So use at your own risk!
Download hard spl v7 from
http://forum.xda-developers.com/showthread.php?t=296722
thanks guys i did it
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
puca said:
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
Click to expand...
Click to collapse
start the device in bootloader, what is displayed?
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Rockford_622 said:
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Click to expand...
Click to collapse
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
hi mrvanx
thanks for your reply after checking the bootloader it has changed to 2.10 olie it did it so fast i thought it had failed will check properly next time and have successfully flashed it to crc 9 and it runs great thanks for all the help
mrvanx said:
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
Click to expand...
Click to collapse
I appreciate your reply Mr. Vanx. Same as with puca, I put my phone into the bootloader mode and it does indeed show the correct 2.10 Olipro version. This is the 3rd 8525 I have had and I could have SWORN it took much longer on the first 2. Even the update from WM5 to WM6 seemed to take much less time with this particular phone. Guess I shouldn't really complain
Downgrade Error 260
Hi Mr Vanx I have followed your guide to downgrade my current SSPL (2.10 Olipro) to SSPL (1.11). But I keep getting error 260. I have followed guide step by step.
I have even tried flashing from SD-Card (by renaming to HERMING.nbh). Process runs successfully, but nothing happens.
Its still showing SSPL-2.10 Olipro in bootloader. Am I missing anything?
Thanks
can some one point me to the guide. I am facing a NO GSM problem on vodafone VPA 1605 with following config:
ROM Version: 1.20.161.6
Radio: 1.03.06.00
CID: VODAP001
Bootloader: 1.04
I do not see the radio version or the IMEI. So I would like to do a HARDSPLv7 followed by Radio ROM update to 1.06.00.10. I hope this will work. Seniors may help with their sggestion.
Can someone help me with the guide to HARDSPL as I am doing it for the first time and the guides are not available at MR Vanx site nor can I locate the sticky?
regards,
H
have you read the first page?
cant uprade from spl 1.40 to 2.04
am using hermes 300 and i want to uprade from 1.40 t o 2.40 but i cant do it.i ve tried can anyone help
dania
How to hard reset without win
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
majida said:
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
Click to expand...
Click to collapse
you should try the hard reset iMate 9502 posts by martin_yo in http://forum.xda-developers.com/showthread.php?t=407336&page=2
Code:
After Flashed with the new ROM, My Device is now stuck in iMate Blue Screen Logo....!!!
But Don't worry Guys...it can be solved with manually hard Reset...
1. Remove battery and reinsert (to make sure the phone is off).
2. Hold down Fn and the Green button (with the phone icon on it) and press the power button.
3. You will see the white hard reset option screen almost immediately. Press the Left Soft Key to hard reset.
Work for me...
but !!
With many thanks Hakim
But I know hard reset of my phone, I did it many time before, unfortunately it dosen't work this time. I tried all I knew about hard reset. but I couldn't do anything for my phone.
I tried (FN+Green+power like last time I did hard reset easy)(FN+Green+reset button)It don't sho any reaction.
Please help me.

HTC 7500 stuck at white screen - Please help ???

Hi,
I just flashed my HTC 7500 with SPL 1.2 by installing AthenaWrapper which went through successfully. After upgradation , I flashed the ROM with SPL3.5_R6.5_B3_WM6.5_B21198.rar which also got installed successfully with no errors at all. However after installation , when the HTC was starting , it is just stuck at white screen and does not go ahead at all. I have tried all things including hard reset , but the phone does not come out of the white screen.
Can someone please help URGENTLY ? have I missed something during the installation ? How can I get the unit to boot atleast . In the bootloader screen , the SPL does show as 1.2.
Kindly help please ???
Thank you.
superlifer said:
Hi,
I just flashed my HTC 7500 with SPL 1.2 by installing AthenaWrapper which went through successfully. After upgradation , I flashed the ROM with SPL3.5_R6.5_B3_WM6.5_B21198.rar which also got installed successfully with no errors at all. However after installation , when the HTC was starting , it is just stuck at white screen and does not go ahead at all. I have tried all things including hard reset , but the phone does not come out of the white screen.
Can someone please help URGENTLY ? have I missed something during the installation ? How can I get the unit to boot atleast . In the bootloader screen , the SPL does show as 1.2.
Kindly help please ???
Thank you.
Click to expand...
Click to collapse
Hi there,
You have answered your own question. you up graded to spl1.2 and then flashed with an spl3.5 rom. you should have flashed an spl 1.2 rom. To use an spl 3.5 rom you need to upgrade again with AP4.0 rom that has the upgrade built in. there is no other way of doing it.
Now you will have to fix your athena with THIS HELPread from post 33onwards, and please read the athena WIKI.
Best of luck
Jay
Hello Jay,
Thanks for your quick reply. How do I get the Athena connected to my PC now ? I can't connect it through Activesync as it does not boot and is in white screen. Also I tried to put it in boot loader mode and then run the updater.exe but it displays a 'Timeout message ' whether the device is coonected and that Active sync is running ?
Can I install 1.2 ROM if that's possible ? If yes , can you let me know which ROM with SPL 1.2 ver can work ? I am just worried now as my Athena may be completely dead and I can't use it.
Can you help ? Thanks once again.
Hi Jay , Folks,
I am writing the codes that I see when I put Athena in bootloader mode :
[email protected])
IPL-v1.00
[email protected]$)
SPL-v1.20.Olipro
From this info , can it be fixed ? Please help
Thanks
Hi superlifer
welcome to the joys of flashing!
Jay has given you a solution to your problem.
Guess what!
You are not the first person to make the mistake you have made and it is documented in several places.
Jay pointed you to the specific post that will fix your problem but he also mentioned you should read the wiki.
i will add to this that you should also read the sticky threads at the top of this forum which include "the beginners guide to upgrading the ROM"
and another thread titled "How to FIX INVALID MODEL ID after bad flashing"
You have corrupted the radio by trying to flash an SPL3.5 ROM onto a phone formatted for SPL1.2.
These roms are different sizes and it wont fit, leading to the unintended consequence.
As I said in the beginners guide , you can flash from bootloader(the 3 coloured screen"
I hope all new owners read this thread and the others I mentioned as it will help prevent the angst you are feeling.
regards lakeman
Hello Jay, Lakeman, Cmonex,
Absolutely brilliant !!
My Athena is breathing again and is out of the dead white screen. I followed the steps to fix the model id and wifi (from CMonex ) and was able to overwrite the model id successfully. I then flashed it with ROM WM6.1 MULTILANG R6.1 MiChY which also got installed successfully. On bootloader screen it now shows as:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20.Olipro
Many thanks first of all to you all and your timely reponses and perfect guidance.
I just want to know now which is the best stable SPL1.2 ROM now which i can install. I want to install 1.2 ROM with HTC Plugin and the big Digital clock and also which will have GPS. My previous ROM had QuickGPS which doesn't seem to be there now and is there way I could get it back. How can I use GPS on Athena.
Apologies as this device is completely new to me i am still getting used to its functions by reading lot of articles and WIKI for this model.
I am scared to put SPL3.5 as I might break something again. My donation is on its way.
Cheers
Just update to the 3.5 spl much much easier that way instead of waiting for anyone to backport their stuff to the 1.2 spl

device stuck in spalsh screen

Hello
after upgrading i'm stucked in spalsh screen (the one with rom version and others...). can i skip this step? the device is lost?
do you have others questions?
Cheers
no one?
Hi.. did I broke the device?
Cheers
Hi!
Give us more info about your device.
IPL,SPL,installed ROM,etc
Did you try hard reset?
BR
Szig
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Stuck in splashscreen
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
punker1993 said:
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
Click to expand...
Click to collapse
ChrBeck said:
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Click to expand...
Click to collapse
Hi!
As you can see mostly it is hopeless.Rarely rehotting DOC chip can help and I read somewhere that sometimes flashing helped,but that was a desperated try with Prophet ROM or something like that.If I was you I could try to flash it with Goldcard (just from curiousity and nothing to lose),but if ChrBeck can't help then who?
BR
Scootie
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
ChrBeck said:
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
Click to expand...
Click to collapse
Hi!
Thanks for the answer.
Just a few things:
I'm in searching for an AKU1 ROM.I had it on my computer years ago,but it lost when my HDD damaged.If I find it,I will upload it for you.
The heating up:in this case probably it doesn't help.When we have a device that can't be flashed properly,we try this and it helps more often than you think.Not only with PDAs,but with phones too.
Goldcard SH¤T:
I know what is Goldcard about.
The reason I mentioned it,it helped me 3-4 times when the device (not only Charmer,other devices too) stuck on bootloader or splash screen after flashing.I didn't have too much time in the workshop,so I tried this and worked.
I don't want to argue with you,I know you are an expert in this,I just tried to help with my experiencies.
BR
Scootie
P.S.:I found it on the xda-developers ftp server: RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship.rar
ftp://xda:[email protected]_1120223_11202110_11220_T-MobileUK_Ship.rar
OK nice that you found the ROM. Maybe we'll have a new test package for the fix of format failed error soon then.
And yes you are right sometimes Goldcard helps if you have forgotten to flash HardSPL or it is damaged then it may help but you need to have acces to OEMSPL and we don't have it.
So hope I can do something soon.
Hi!
I have a question:
I have a Charmer with IPL,SPL 3.08.Unfortunately it is CID locked,so I can flash it with official v3 ROMs only.Is there any solution to downgrade it?Or with JTAG only?
Thanks in advance!
BR
Scootie
The NoID RUU will be able to downgrade it.
Hi!
I tried that,but:
1.flashing is successful,but nothing has changed,I get the old OS after upgrade
2.I tried the v1 ROM I found.The IPL has been changed to 1.12,but the SPL remained 3.08.The OS has been changed in this case,so it worked flawlessly.
The CID unlocking methods didn't work (obvious,SPL was 3.08).
After that I tried to upgrade it,but it was a torture.I got errors and errors,but after an hour finally I could upgrade it successfully.
So,if you have an idea,I have a device to test it.
BR
Scootie
The IPL is down means it worked. After that you can flash a Prophet ROM.
What ROM of Prophet?
High, I was today flashing my Charmer with all original ROM I mean and the flashing process behaves OK, after flashing, it writes "Congratulation" and all the things like OS, Radio, IPL... are change to the definite ROM. But it's all. It will stuck in the splash screen... I have read in this thread something about Prophet ROM. What is it?
The prohpet ROM is an official Prophet AKU 2 flashable after downgrade.
System is as follows:
Fist flash the Charmer AKU1
Then flash a Prophet AKU2
Then flash Charmer Aku3.
You need to do all these steps with the NOID RUU.
That should fix the HardReset failing.
I'm working to get a tool running that does the whole thing automatically.
THX
Oh ****, Thanx 4 quickly answer...And I'm waiting :-D
Ok, so now I'm having
IPL 1.12
SPL 1.12.0000
GSM 01.12.20
OS 1.12.2.23
And I'm waiting 4 your instructions...
How have you gotten the SPL down?
Normally, with flashing... It can be flashed with every ROM...
OK. Cause normally SPL stays up. I never saw a full downgrade.

Categories

Resources