HTC 7500 stuck at white screen - Please help ??? - Advantage X7500, MDA Ameo ROM Development

Hi,
I just flashed my HTC 7500 with SPL 1.2 by installing AthenaWrapper which went through successfully. After upgradation , I flashed the ROM with SPL3.5_R6.5_B3_WM6.5_B21198.rar which also got installed successfully with no errors at all. However after installation , when the HTC was starting , it is just stuck at white screen and does not go ahead at all. I have tried all things including hard reset , but the phone does not come out of the white screen.
Can someone please help URGENTLY ? have I missed something during the installation ? How can I get the unit to boot atleast . In the bootloader screen , the SPL does show as 1.2.
Kindly help please ???
Thank you.

superlifer said:
Hi,
I just flashed my HTC 7500 with SPL 1.2 by installing AthenaWrapper which went through successfully. After upgradation , I flashed the ROM with SPL3.5_R6.5_B3_WM6.5_B21198.rar which also got installed successfully with no errors at all. However after installation , when the HTC was starting , it is just stuck at white screen and does not go ahead at all. I have tried all things including hard reset , but the phone does not come out of the white screen.
Can someone please help URGENTLY ? have I missed something during the installation ? How can I get the unit to boot atleast . In the bootloader screen , the SPL does show as 1.2.
Kindly help please ???
Thank you.
Click to expand...
Click to collapse
Hi there,
You have answered your own question. you up graded to spl1.2 and then flashed with an spl3.5 rom. you should have flashed an spl 1.2 rom. To use an spl 3.5 rom you need to upgrade again with AP4.0 rom that has the upgrade built in. there is no other way of doing it.
Now you will have to fix your athena with THIS HELPread from post 33onwards, and please read the athena WIKI.
Best of luck
Jay

Hello Jay,
Thanks for your quick reply. How do I get the Athena connected to my PC now ? I can't connect it through Activesync as it does not boot and is in white screen. Also I tried to put it in boot loader mode and then run the updater.exe but it displays a 'Timeout message ' whether the device is coonected and that Active sync is running ?
Can I install 1.2 ROM if that's possible ? If yes , can you let me know which ROM with SPL 1.2 ver can work ? I am just worried now as my Athena may be completely dead and I can't use it.
Can you help ? Thanks once again.

Hi Jay , Folks,
I am writing the codes that I see when I put Athena in bootloader mode :
[email protected])
IPL-v1.00
[email protected]$)
SPL-v1.20.Olipro
From this info , can it be fixed ? Please help
Thanks

Hi superlifer
welcome to the joys of flashing!
Jay has given you a solution to your problem.
Guess what!
You are not the first person to make the mistake you have made and it is documented in several places.
Jay pointed you to the specific post that will fix your problem but he also mentioned you should read the wiki.
i will add to this that you should also read the sticky threads at the top of this forum which include "the beginners guide to upgrading the ROM"
and another thread titled "How to FIX INVALID MODEL ID after bad flashing"
You have corrupted the radio by trying to flash an SPL3.5 ROM onto a phone formatted for SPL1.2.
These roms are different sizes and it wont fit, leading to the unintended consequence.
As I said in the beginners guide , you can flash from bootloader(the 3 coloured screen"
I hope all new owners read this thread and the others I mentioned as it will help prevent the angst you are feeling.
regards lakeman

Hello Jay, Lakeman, Cmonex,
Absolutely brilliant !!
My Athena is breathing again and is out of the dead white screen. I followed the steps to fix the model id and wifi (from CMonex ) and was able to overwrite the model id successfully. I then flashed it with ROM WM6.1 MULTILANG R6.1 MiChY which also got installed successfully. On bootloader screen it now shows as:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20.Olipro
Many thanks first of all to you all and your timely reponses and perfect guidance.
I just want to know now which is the best stable SPL1.2 ROM now which i can install. I want to install 1.2 ROM with HTC Plugin and the big Digital clock and also which will have GPS. My previous ROM had QuickGPS which doesn't seem to be there now and is there way I could get it back. How can I use GPS on Athena.
Apologies as this device is completely new to me i am still getting used to its functions by reading lot of articles and WIKI for this model.
I am scared to put SPL3.5 as I might break something again. My donation is on its way.
Cheers

Just update to the 3.5 spl much much easier that way instead of waiting for anyone to backport their stuff to the 1.2 spl

Related

Prophet not upgraded just tri colour screen

Hi there, I have just upgraded or should i say tried to upgrade to the new WM6 coffie ROM and the Krystal ROM but with both of these I can flash, however upon reboot it stays at the 3 colour screen
I have followed the Hard SPL guide for a G3 ---- Check
So what have I done? please someone help - it's a mates phone
also I tried to go back to the original WM5 from the FTP site, but it fails because I have updated the SPL, I would appreciate a link to a WM5 that doesn't check and that is in english........ if that would fix the problem
One last thing - i tried to use the update tools again but it says there is no device connected so I did a hard reset and tried again but no go, after a hard reset i can flash the other roms though
cheers all
No Panic !!
andytof47;1862521 said:
Hi there, I have just upgraded or should i say tried to upgrade to the new WM6 coffie ROM and the Krystal ROM but with both of these I can flash, however upon reboot it stays at the 3 colour screen
I have followed the Hard SPL guide for a G3 ---- Check
So what have I done? please someone help - it's a mates phone
also I tried to go back to the original WM5 from the FTP site, but it fails because I have updated the SPL, I would appreciate a link to a WM5 that doesn't check and that is in english........ if that would fix the problem
cheers all
Click to expand...
Click to collapse
No Panic~~~
Pls try to have a look to the link at my signature
( HardSPL easier)
please reply if ok!
I thought The sticky on top of the forum covered this
Hey there, would this be the problem? I thought Jumpspl was included in the initial upgrade tools folder?
Is this the same? and also does this problem (tri color screen) happen when it hasn't been properly flashed with the hard spl?
cheers
andytof47 said:
Hey there, would this be the problem? I thought Jumpspl was included in the initial upgrade tools folder?
Is this the same? and also does this problem (tri color screen) happen when it hasn't been properly flashed with the hard spl?
cheers
Click to expand...
Click to collapse
that is good and for experience users, mine is mostly for juniors. Please read and nothing bad.
The jumpspl... 100% work, and follow the steps, never fail.
Will your method work when not booting?
Just read your method and I hope to try it soon, but will your method work if it is not booting --- the method sounds like it needs the system to boot is this correct?
I hope it will work on this system while it is not booting...... I will let you know
OK I just read the whole post -------- The only file I can see is the jump spl.zip --
is that the hard spl or what?
dioxda2 I see how helpfull you are and thanks so far but how do I get the phone out of recovery mode or whatever mode that is??? what is the file I need??? please
thanks heaps

Help please! My ROM upgrade broken my Athena!

Hello, I am in serious trouble! I got a brand new HTC Athena with Windows Mobile 5.0. I succesfully upgrade it to Windows Mobile 6.0.
All was OK.
Than I was interested to move into Windows Mobile 6.1 and possibly 6.5. At first I did the Athena unlock (3 step process) and all went OK: Antenna 1.5.0, SPL 1.2 OLI....
THAN I DID MY ERROR! I try to upgrade my 6.0 ROM with the Micky 6.1 cooked file with SPL 3.5. After a 92 percent upgrade, the ROM crashed and now I always get a nasty black screen with few lines (No 3 color bands!). When I try to upgrade again the same ROM or ROM for SPL 1.2 I get an error (ID mismatching). I guess the only solution is a hard and full reset of the Windows. But doing only a hard reset with the PDA will NOT change my error message and I will keep see this nasty black screen and I cannot load the Windows ActiveSync application-
I am totally lost. Help please. Any tool for a true full restore/recover??? (I did NOT make any backup!).
This thread might hold a solution to your problem.
Hi
If you follow the instructions exactly in post 33, it will solve your problems. just click HERE
Jay
Hello, those links are basically for corrupted wifi antenna files.-
In my case my HTC Athena crashed the Windows 6 ROM while I was attempting to upgrade, after unlocking the phone, the Athena from version 6.0 to version 6.1
Are you sure I can use the post #33 also for my specific trouble?
Thank you in advance!
this is also to repair your bootloader-infos
if you look at your bootloaderscreen, you will see ATHE100, IPL, ATHE100, SPL. if not, you have to repair it
make sure you flashed the right rom, spl 1 or 3.5
How can the bootloader get repaired?
yes use that link, post #33. fixes both wifi and modelid problems and bootloader problems when you got stuck at 92% of the flashing process.
Cannot re flash ROM
Please help! I tried the unlocker and it failed at 92% and since then I have no WM6. Then I tried to flash the Michy WM6.5 and that failed. I was getting model id errors so I did the mtty and mac1 fix which was succesful. However all I can get now is a grey screen on boot-up. I can get to the bootloader screen and it displays ATHE100, IPL-v2.02, ATHE100, SPL-v1.20. Olipro. From what I have read on the forum at this stage I should run a RUU to flash a WM6 ROM but all that I try can't connect because no OS running to connect with Activesync? Is there a way to flash from the bootloader? The other option seems to be putting an image and flasher on a miniSD but I can't find clear instructions for this or which files?
Please ignore - my battery wasn't charged enough. Replaced battery and recovered device.
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
I have follow the link (thread 33)...., however, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
first, how can I get the mac address of my device? It is NOT written anywhere in the Athena parts (checked in the battery bay and so on.....), and so when I run mtty i am in trouble! I have used a mac address got from my company's manager, but not sure it is ok to use it with the Athena!
Anyway,......I have follow the post link (thread 33)...., and followed the various steps.- However, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Solved!
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
puffo said:
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
Click to expand...
Click to collapse
Can you tell what you've actually done after you've changed ROM with Mtty?
I done the thing with Mtty but just as you described when I reset it now I still get the grey screen. And if I try to update ROM it fails again on 92%
where did you find the upgrade from wm5 to wm6?
the link I found on rapidshare seems not be availabel anymore

I mate smartflip Please someone helpp...!

I tried to flash rom wm 6.1 edition but suddenly when flashıng was %80, its broke and failure.
Now my phone broke only htc pic came.Please some one help.I read all the post about it.I cant master reset on my phone because when i push the 0 button htc pic came again.Only bootloader mode can works but ı try many than 10 roms it starts but when they are %5-4 ,they broke too.Then this type came "İmage file corrupted and please check update utiltiy"
I read at one blog if this situtaion came i must use smartflip stock rom to flash but i cant find imateclub's web site is broke too.
Here is the smartflip official rom http://rapid share.com/files/307222427/i-mate_smartflip_WWE_1.2.301.2_ship.exe
check my post about gold card method, and then you could flash with your official rom
Hello everyone
i got similar problem too. it can restart the phone but goes to all white screen.
i even tried over 15 Roms to reinstall it but it all got failed.
Here is my phone video below
http://www.youtube.com/watch?v=W9h91HWdkvA
Please give me some help.
Thank you so much
someone had told because i have IPL 1.02 & SPL 1.02 but with WM6 above system.
i need to re flash phone to IPL 2.00 & SPL 2.00, BUT .....How to do it ?
Please help!!
Thanks
read my post about gold card method. i had the same problem and recoverd my phone. good luck

device stuck in spalsh screen

Hello
after upgrading i'm stucked in spalsh screen (the one with rom version and others...). can i skip this step? the device is lost?
do you have others questions?
Cheers
no one?
Hi.. did I broke the device?
Cheers
Hi!
Give us more info about your device.
IPL,SPL,installed ROM,etc
Did you try hard reset?
BR
Szig
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Stuck in splashscreen
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
punker1993 said:
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
Click to expand...
Click to collapse
ChrBeck said:
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Click to expand...
Click to collapse
Hi!
As you can see mostly it is hopeless.Rarely rehotting DOC chip can help and I read somewhere that sometimes flashing helped,but that was a desperated try with Prophet ROM or something like that.If I was you I could try to flash it with Goldcard (just from curiousity and nothing to lose),but if ChrBeck can't help then who?
BR
Scootie
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
ChrBeck said:
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
Click to expand...
Click to collapse
Hi!
Thanks for the answer.
Just a few things:
I'm in searching for an AKU1 ROM.I had it on my computer years ago,but it lost when my HDD damaged.If I find it,I will upload it for you.
The heating up:in this case probably it doesn't help.When we have a device that can't be flashed properly,we try this and it helps more often than you think.Not only with PDAs,but with phones too.
Goldcard SH¤T:
I know what is Goldcard about.
The reason I mentioned it,it helped me 3-4 times when the device (not only Charmer,other devices too) stuck on bootloader or splash screen after flashing.I didn't have too much time in the workshop,so I tried this and worked.
I don't want to argue with you,I know you are an expert in this,I just tried to help with my experiencies.
BR
Scootie
P.S.:I found it on the xda-developers ftp server: RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship.rar
ftp://xda:[email protected]_1120223_11202110_11220_T-MobileUK_Ship.rar
OK nice that you found the ROM. Maybe we'll have a new test package for the fix of format failed error soon then.
And yes you are right sometimes Goldcard helps if you have forgotten to flash HardSPL or it is damaged then it may help but you need to have acces to OEMSPL and we don't have it.
So hope I can do something soon.
Hi!
I have a question:
I have a Charmer with IPL,SPL 3.08.Unfortunately it is CID locked,so I can flash it with official v3 ROMs only.Is there any solution to downgrade it?Or with JTAG only?
Thanks in advance!
BR
Scootie
The NoID RUU will be able to downgrade it.
Hi!
I tried that,but:
1.flashing is successful,but nothing has changed,I get the old OS after upgrade
2.I tried the v1 ROM I found.The IPL has been changed to 1.12,but the SPL remained 3.08.The OS has been changed in this case,so it worked flawlessly.
The CID unlocking methods didn't work (obvious,SPL was 3.08).
After that I tried to upgrade it,but it was a torture.I got errors and errors,but after an hour finally I could upgrade it successfully.
So,if you have an idea,I have a device to test it.
BR
Scootie
The IPL is down means it worked. After that you can flash a Prophet ROM.
What ROM of Prophet?
High, I was today flashing my Charmer with all original ROM I mean and the flashing process behaves OK, after flashing, it writes "Congratulation" and all the things like OS, Radio, IPL... are change to the definite ROM. But it's all. It will stuck in the splash screen... I have read in this thread something about Prophet ROM. What is it?
The prohpet ROM is an official Prophet AKU 2 flashable after downgrade.
System is as follows:
Fist flash the Charmer AKU1
Then flash a Prophet AKU2
Then flash Charmer Aku3.
You need to do all these steps with the NOID RUU.
That should fix the HardReset failing.
I'm working to get a tool running that does the whole thing automatically.
THX
Oh ****, Thanx 4 quickly answer...And I'm waiting :-D
Ok, so now I'm having
IPL 1.12
SPL 1.12.0000
GSM 01.12.20
OS 1.12.2.23
And I'm waiting 4 your instructions...
How have you gotten the SPL down?
Normally, with flashing... It can be flashed with every ROM...
OK. Cause normally SPL stays up. I never saw a full downgrade.

[Q] Another bricked Athena?

Ok, after 2 days of fighting, sweating, a pc hdd full with roms,tools,mtty,etc...
...i'm giving up. i am posting a help request for the first time since i am a xda user,
and that's been for almost 2 years now. i rather solve problems by doing research on the xda forums but this time i am out of energy.
i had an raphael before where the hacking process was pretty straightforward
and flashing a cooked rom was really idiotproof.
now i got an cool athena in my hands. i was like yeah, let's flash baby....and
the original OS didn't even last for half of a day. quick enough i realised that
this baby shouldn't be flashed the raphael way - the sd card method...
ok let's get on topic:
what i did:
flashed with the AP4 SPL 3.5 AthenaUpdater (following the howto exactly)
and well. that worked fine. the OS was booting and everything. but to my
surprise it looked like that AP4 update flash thing didn't ship another cooked
rom, but flashed my SPL only. i rather expected a SPL, CID unlock and ROM
install in one single package. i don't know what made me think that, since the
raphael has to be flashed with different stuff too before beeing able to...bla
since i was so happy to find that AP4 update howto i guess i was assuming
that this is the whole deal since it doesn't say anything about seperate CID
unlocking in that .pdf
anyway, i looked for a cooked spl 3.5 compatible rom and there i found it:
[ROM] *Updated Mar/4/2010* AGB V3.00.0 (WM6.5.5 build 23534)
and well, that was basically it. the flash went ok, but after booting only
the rom's splash screen appears and nothing further happens. hard reset
doesn't help.
i tried a few other roms after that, and again. only the rom-specific custom
flash image appears and nothing happens.
tried to flash the AP3 for SPL 3.5 ROM - same thing: flash screen says "operating system is loading", which is an bitmap picture i guess...
downgrade to SPL 1.2 doesn't seem possible since this requires a running
WM, which i don't have.
bootloader works by the way, hard reset works too, but no fix...
after a little reading i get the idea that i should have cid unlocked the device
before flashing with a cooked rom? or did i something else wrong?
any help would be appreciated
oh yeah, and mtty:
the recover from invalid id procedure doesn't fix the issue.
and:
set 14 0
task 8
doesn't fix anything too, just boots the device into the never ending flash screen....
quick questions
what does your boot screen say
and did you remove your sd and simcard before flashing
yeah, the i ofcourse removed the sd card and sim card before everything.
i am at work now but afaik my bootloader screen says:
ATHE100
IPL 2.02
SPL 3.50.Olipro
before the attempt with mtty it said
ATHE400
IPL 2.02
SPL 3.50.Olipro
something like that. is that helpful?
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
ultrasonyk said:
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
Click to expand...
Click to collapse
Hi mate
I live in a different time zone and my daily email about updates to posts comes late in my day and probably when you sleep.
There are not many people who use this device and it is really a legacy machine.
However your post gives a clue to what happened.
with the bootscreen showing athe400 initially are you sure you have an x7500/x7501 or is it the x7510?
Just make sure before you follow the solution in this thread
http://forum.xda-developers.com/showthread.php?t=387596&highlight=endless+loop
the roms are very different
Check out exactly which hardware you have
this thread is from the x7510 thread and may be worth a read if you have the x7510
Additionally cmonex has the knowlege to fix your issuues if the above doesn,t work
http://forum.xda-developers.com/showthread.php?t=441684
thank god, somebody replied with useful information
well, i must be honest i didn't pay too much attention on the model number.
after reading your post, i checked and i see that i have a X7510 advantage device.
which means as far as i can understand it:
i SHOULD have the modelid ATHE400?
which means, i messed it up by flashing it with mtty to modelID ATHE100?
which means, all the time i was installing X7500 stuff on the wrong device
and bricked it that way?
so the AP4 3.5 SPL solution is not for X7510?
which means, the AP4 3.5 SPL is a hard SPL but for another device?
and after all, what do you suggest? do i need to revert my modelID
to ATHE400 and if yes, how? and after that i should follow the 2nd
thread to install a proper hardSPL and a WM6.5 ROM of my choice?
try contacting cmonex
the author of this thread
http://forum.xda-developers.com/showthread.php?t=441684
wrote the script you used to change the device id and may have a way to reverse this
good luck
lakeman, my friend!
you pointed me to the right direction. i followed the steps for installing
hardspl for x7510 from cmonex, and yeah, the modelid changed back
to athe400 and the device was booting! seems like that hardspl also
corrects the modelid automatically.
i am still curious why the device was working after flashing with AP4 3.5 SPL
in first place, since that one is actually for X7500 devices.
i should 've read some more before going to flash that thing, i must admit.
many thanks to you lakeman, and big ups for that cmonex guy!
now it's time to look for a nice wm6.5 rom for my ATHE400
fantastic
happy to help

Categories

Resources