I've been trying to figure this out... is it possible to run Olipro 2.4 on Vista 64? I keep getting error messages that it does not work, but am I missing something?
Hi jondixon:
In my experience, I recommend you to update your HTC MOGUL PPC-6800 only under Windows XP-SP2 with Microsoft ActiveSync 4.5
I run my HTC MOGUL PPC-6800 under Windows Vista-64 bits-SP1 with Windows Mobile Device Center 6.1.6965 but it's only for Sync with Outlook 2007
TecMan
SPRINT HTC MOGUL PPC-6800
ROM version: dcd 3.0.1
Radio version: 3.35.04
SPL-2.40.Olipro
While I do prefer XP for flashing, I have used Vista Ultimate x64 without any issues to do so as well.
I'm using Vista 64 Ultimate and I've updated my phone numberous times. Succesful every time.
I'm using Vista 64 Ultimate and olipro wouldn't even run. Why?
Same thing here. Vista Ultimate X64. cant use olipro, had to do it on my work pc which is xp 32 bit. but other flashing is no problem at all.
it is because the sleep4 command is 16bit which is not allowed to to run on 64 bit os
just edit the cmd file in a text editor and replace sleep4 with pause
now it will pause when it runs which means you have to hit enter to continue which should be enough a delay
i just did this exact same thing tonight without issue
Wow MrTek.. that worked...
But i had already done it on an XP32 system before I read your siguestion... damn... i could have not botherd the neighbor for his PC afterall.....
Yeah i wish someone would rewrite sleep4 in x32.....
Also.. its not that its "not allowed" its that its totally UNABLE to... due to the x64 CIA (figure it out urself..)
MrTek said:
it is because the sleep4 command is 16bit which is not allowed to to run on 64 bit os
just edit the cmd file in a text editor and replace sleep4 with pause
now it will pause when it runs which means you have to hit enter to continue which should be enough a delay
i just did this exact same thing tonight without issue
Click to expand...
Click to collapse
Just wanted to say, this worked for me as well. I was able to install Olipro 2.40 from Vista 64-bit with this work around.
you should unlock under XP/activesync. Flashing on vista x64 is fine, works great, but I didnt try very hard to run the unlocker under vista when I had an XP machine to install activesync on once and never touch my mogul with again.
On second thought, adjust the .bat as instructed above and dont worry about it. As I said, didnt try very hard.
TecMan45 said:
In my experience, I recommend you to update your HTC MOGUL PPC-6800 only under Windows XP-SP2 with Microsoft ActiveSync 4.5
Click to expand...
Click to collapse
For the utils we use, Vista 32 is fine.
flash numerous times with vista home premium no probs at all
how do you edit the cmd file in a text editor. can i please have step by step instructions.
My laptop is XP and desktop 64 for situations like this. I actually did ALL of my flashing via my laptop, didn't know until this thread I could still do it with 64.
Why not just run NueTools SPL Unlocker? Then you can get it all done from the phone and not having to worry about Vista or XP or whatever else...
http://www.nuerom.com/BlogEngine/page/nueSPLnueSPL-ReLocker-for-the-HTC-Titan.aspx
i would but i only have one microsd card and i might mess it up.
MrTek said:
it is because the sleep4 command is 16bit which is not allowed to to run on 64 bit os
just edit the cmd file in a text editor and replace sleep4 with pause
now it will pause when it runs which means you have to hit enter to continue which should be enough a delay
i just did this exact same thing tonight without issue
Click to expand...
Click to collapse
AWESOME!!! Thanks for the help... I think I just successfully unlocked my alltel Vogue on Windows Vista 64! Did exactly what MrTek suggested... Alot of "hit any key to continue..." but it worked! I might have the same roaming problem that many people experience but hopefully I can fix that. Thanks a bunch! Now for some ROM cooking...
UPDATE: Solved the roaming issue by updating my prl (preferred roaming list)...
1. Dial *228
2. Hit option 3
3. Wait for phone to program and restart.
(I believe this can only be done while on an Alltel tower, or whichever carrier you happen to use.)
Related
This is my first post, though I've been pouring over the forums everyday for a few weeks to try to get up to speed. You may notice that my join date is quite recent, but I only recently signed up! I finally replaced the broken usb port last night and then flashed wm6 from htc onto my hermes. This morning I've been trying to install Hard-SPL-V7, which failed, then I successfully ran the SIM/CID unlocker, and finally tried to run HERM-SSPL which failed. What seems to be happening is that after syncing and running RUUWrapper.exe the device goes to the bootloader screen:
Code:
HERM100
IPL-1.04
HERM100
SPL-2.03
But doesn't do anything else, and then the PC reports a disconnect error. I think that the device is supposed to reboot after going to the bootloader, but it doesn't. I have noticed that shortly after going to the bootloader, it flashes a white screen with red text, and then returns. It's so fast I can't read the text. After the error prompt on the pc (vista), I soft-restart the device and it returns to the today screen where everything appears to be normal.
What am I doing wrong? I read the guide for installing the hard-spl. RUU_signed.nbh is in the same directory on the pac as RUUWrapper.exe. The device isn't bricked. I'm stumped.
I appreciate any and all help. I know it's painful to keep answering the same questions over and over again, so I promise that I've been searching for an answer in the wiki and on the forums.
Also, thank you for these utilities, roms, forums, etc. It's amazing that so much is being accomplished by apparently so few.
***UPDATE***
More information is always better...
After wmdc is connected I run RUUWrapper.exe
I check Force using SSPL and go through the prompts...
Code:
From:
Image Version : 3.62.502.3
To:
Hard-SPL-2.10
The device goes to the SSPL as opposed to the SPL, I think, and displays this:
Code:
HERM100
IPL-SSPL
HERM100
SPL-1.09.ds
Then the pc prompts 'Verifying ...'
The device stays one the bootloader screen, and then the pc prompts:
Code:
ERROR[260] UPDATE ERROR
When I soft reset the device, it comes up to the today screen, and going to the bootloader displays this:
Code:
HERM100
IPL-1.04
HERM100
SPL-2.03
OK, I think I know what's going on.
I thought that I had gone through installing the vista x64 drivers from the guide but I hadn't. It doesn't matter much though as vista x64 really doesn't like unsigned drivers. I've not been able to get past that. So the issue was that vista x64 can't sync with hermes in bootloader mode. OK, fine, I guess that I'll be working with XP. Why oh why did I decide to try vista x64...
Has anyone else found a solution to this?
mangiaculo said:
OK, I think I know what's going on.
I thought that I had gone through installing the vista x64 drivers from the guide but I hadn't. It doesn't matter much though as vista x64 really doesn't like unsigned drivers. I've not been able to get past that. So the issue was that vista x64 can't sync with hermes in bootloader mode. OK, fine, I guess that I'll be working with XP. Why oh why did I decide to try vista x64...
Has anyone else found a solution to this?
Click to expand...
Click to collapse
Id stay clear of vista when trying to do flashing stuff....it REALLY just messes with all aspects of the process, regardless of if the WMDC is up to date.
Best thing to do is to get 32bit XP fired up and use that its just so much easier and everything else you use wont have to be patched/tweaked to behave on XP. LOL my vista config guide should really be a sly 'Uninstall vista, format and install XP SP2......guide'.
when you ran the SIM/CID unlocker, did you run it from your Storage card or did you use your usb to install? i think i had a similar issue. it would always give me the error 260. First, i sim/cid unlock my phone via storage card and it said unlocked and everything, but it still gave me the error 260. then i decided to just try to SIM/CID unlock via USB and when i did that, i didn't get the error 260 but instead it updated to Hardspl v7. hope that makes sense.
mrvanx said:
Id stay clear of vista when trying to do flashing stuff....it REALLY just messes with all aspects of the process, regardless of if the WMDC is up to date.
Best thing to do is to get 32bit XP fired up and use that its just so much easier and everything else you use wont have to be patched/tweaked to behave on XP. LOL my vista config guide should really be a sly 'Uninstall vista, format and install XP SP2......guide'.
Click to expand...
Click to collapse
Thank you both for the responses. I ended up going home and flashing on my xp machine. Our new work machines are 64bit and I had several options for os, and silly me, I thought vista x64 sounded like a good idea. It's been a challenge.
Anywho, hardspl is installed! I also flashed the black 3.0 wm6 rom, though my keymapping is strange for the additional key functions. I'm off to research an answer on that. Thanks!
Would it be possible to install virutal PC on vista 64-bit and just run a virtual instance of 32-bit xp? I guess my real question is whether it is possible to flash the phone from a virtual pc.
-thanks.
hi,
Yes, it is possivel , i do it, i recomend you using VMware soft, because virtual pc doen't have USB support.
With PPCGeeks undergoing their upgrade, where can I download 2.40-olipro from in the mean time? I'm wanting to do some rom upgrades but it seems I need this to unload things for it. I'm trying to install the radio 3.27 and one of the titan 2.x roms with the GPS update.
here u go...
Mod Edit:
Unfortunately the attached file was for an earlier version - see posts below for 2.4
origins81 said:
try hitting search first
Click to expand...
Click to collapse
I did and 2.40 olipro only gave me messages saying that I needed it, not that it was called TitanUnlock. Thanks for the link.
Did I miss somthing?
I downloaded the file and it still said version 1.20Olipro did I miss something?
I saw that it was 1.2 but it didn't register that it was the wrong version and that probably explains the problems I was having trying to load the new rom.
olipro 2.40 here you go
this is the link when ppcgeeks.com comes back up you can get it.
however attached is the file you want and need. BUTTTTTTTTTT
you will now need to find the "re-locker" so you can relock the old olipro and use the new.
Thanks for the file, but I guess if I need to find another program, will wait for either ppcgeeks to come back up or sprint to release the offical rom.
Does anyone have the program for "re-locker"?
Here's the file with the proper name. It's not the easiest to find especially with the other side being down. So without being rude I shall set you in the right direction. Plus if you search for "titan unlocker" as per the other file name you are liable to be loading the OLD unlocker not new since it is generically named such.
edit....
Sorry I guess my interrution while posting this caused me to duplicate someones post....
Thank you for the links. You are far from being rude, but show you understand that all the searching in the world won't help when you don't have the right information and that one of the main supports is missing.
Thank you all for your help! I ended up googling and searching and came upon this post from another board.
"I had the exact same problem.
Connect your phone (while in Windows, not from the bootloader) to your computer and make sure it creates an ActiveSync connection.
Download the file from here: ftp://ppcgeeks:[email protected] . Extract it and it should launch the Titanunlocker.bat. If it doesn't, just launch the batch file from the place you extracted the files. Follow the prompts, and when it's done, you should have 2.40 installed. I too couldn't get 1.20 off, but after I did this, I now have 2.40 bootloader."
----------------
Also if you are stuck with the bootloader screen (rainbow) you can just run titan_exitbl.exe in the file I've included it will allow you to boot. Also you must disable activesync from looking for usb connections if you have to go the titan_exitbl.exe route.
The file listed able will actually attempt to update to 2.40 once you run it, really automated.
Thanks to PDAPhoneHome's jrider for the post.
I was on 1.20, but I didn't have to relock or anything to upgrade to 2.40. I just went onto the bootloader screen, then ran the RUU exe for 2.40 in the TitanUnlocker zip.
Oh boy, uncrackable Apache 6700!
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
Click to expand...
Click to collapse
Dude...this is the Titan forum, not Apache. Why you would try altering your bootloader with unlockers specifically meant for other devices (kaiser & titan) is beyond me.
superlover911 said:
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
Click to expand...
Click to collapse
This post shows that people are not worried about what they do to their phone. 911, you need to read the wiki for your phone (APACHE 6700) and do not use any software or roms for other devices (i.e. 6800, Kaiser, Titan, etc) unless you are 100% certain what you are doing. You are really close to hosing your phone.
Read this twice. http://wiki.xda-developers.com/index.php?pagename=HTC_Apache
x64 compatibility?
Am running XP x64 edition and the 2.4 Olipro wasn't working, saying it cannot run in a 64-bit OS.
Any suggestions/solutions? I don't have access to any 32-bit computers.
EDIT: Already resolved elsewhere:
MrTek said:
it is because the sleep4 command is 16bit which is not allowed to to run on 64 bit os
just edit the cmd file in a text editor and replace sleep4 with pause
now it will pause when it runs which means you have to hit enter to continue which should be enough a delay
i just did this exact same thing tonight without issue
Click to expand...
Click to collapse
Hi Friends:
Today, I tried to run my HTC MOGUL PPC-6800 in Bootloader Mode (SPL-1.07.0000) and then I run ROMUpdateUtility (Hard-SPL-MFG) to update the SPL to 2.40-olipro and I got the following:
- only 0%
- and finally ERROR [262]: UPDATE ERROR
I needed to do the recovery procedure and tired again and got the same results.
Can you help me?
Thanks
TecMan
Sprint HTC MOGUL PPC-6800
Windows Mobile Device Center 6.1.6965
Windows Vista 64-bits
You must establish a Activesync connection first and not be in Bootloader mode then execute Hard-SPL-MFG.exe. Checkout the updated Wiki:
http://wiki.xda-developers.com/index.php?pagename=TitanRecentHome
search is your frined
I recently did the update with 2.40 and DCD's ROM, I had the same issue. I don't know what I did to make it magically work agian. I tried three different times. Anywho, sorry I can't be more help.
Hi Friends:
I solved the Error [262]: Update Error, it was very simple...
1. I run the Microsoft ActiveSync 4.5 with Windows XP-SP2 and then run Hard-SPL-MFG.exe and my NEW SPRINT HTC MOGUL PPC-6800 got a Bootloader Mode with 2.4.Olipro
2. I run RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship.exe and I had the following:
Windows Mobile 6 Professional
CE OS 5.2.1629 (Build 18136.0.4.8)
ROM version: 3.35.651.2
ROM date: 02/22/08
Radio version: 3.35.04
3. in Bootloader Mode, I run DCD_3.0.1_Sprint and I had the following:
Windows Mobile 6.1 Professional
CE OS 5.2.19199 (Build 19199.1.0.0)
ROM version: dcd 3.0.1
ROM date: 02/22/08
Radio version: 3.35.04
Thank you for your support and now my NEW SPRINT HTC MOGUL PPC-6800 is working great!!!
TecMan
Hey guys Im a noob and im having a bit of problems
Im stuck in the bootloader screen
TITA100 MFG
SPL-2.40 Olipro
CPLD-9
My comp has windows vista premium so instead of activesync i have windows device center 6.1 I have unclicked allow USB connections
but i think my comp doesnt recognize that they the phone is connected at all although i do here the sound that lets me know that a usb device is connected
exitbl.exe doesn't work keeps telling me
cannot open USB port
Please make sure that USB connection in Activesync is disabled
Also make sure that your USB cable is properly connected
if it helps im on a bell phone
mrfantastic said:
Hey guys Im a noob and im having a bit of problems
Im stuck in the bootloader screen
TITA100 MFG
SPL-2.40 Olipro
CPLD-9
My comp has windows vista premium so instead of activesync i have windows device center 6.1 I have unclicked allow USB connections
but i think my comp doesnt recognize that they the phone is connected at all although i do here the sound that lets me know that a usb device is connected
exitbl.exe doesn't work keeps telling me
cannot open USB port
Please make sure that USB connection in Activesync is disabled
Also make sure that your USB cable is properly connected
if it helps im on a bell phone
Click to expand...
Click to collapse
Run this to exit the bootloader.
Sorry run what?
Sorry that was the problem i have that the titan_exitbl.exe
and it wont work and gives me the error msg i mentioned
mrfantastic said:
Sorry that was the problem i have that the titan_exitbl.exe
and it wont work and gives me the error msg i mentioned
Click to expand...
Click to collapse
Oops, sorry I misread that the first time.
If you did uncheck the allow usb connections, you may to try killing the device center process. I've had issues with that before (I use Vista as well).
Look for wmdc.exe in the Process list and try killing that. It should work if you then reconnect your phone. I've had success going that route on Vista anyway.
Tried that too didnt work
Weird because i kno my computer realizes something is connected but I try the titan_exitbl.exe and get that error
is it because im running on vista?
help me...
WWE2.15 can be flashed in to 818pro, others can't...
only under xp or with a virtual machine under vista
which virtual machine do you use?
I am running xp on VirtualBox 1.6.4, and i can't flash my qtek s200.
I have configure 1 filter to all my use usb devices.
When i connect my phone, it synce with active sync, but when i run the rom installation program, when my phone displays the bootloader, virtualbox tolds me that it "failed to create a proxy device for the usb device".
Can you tell me how you did?
Note : sorry if my english is aproximative.
sorry i use a old win xp pc
but i hear that it works with VMware
and my english ist also bad too
thank you !
prophet -> throttle diamond and throttle diamon multi lang. both from gullum
kaiser -> throttle II also from gullum
soft and hardspl both phones, everything done under viste home premium 32bit.
no probs at all
and did you try do install tha radio rom 2.19?
schnitzelbrain said:
prophet -> throttle diamond and throttle diamon multi lang. both from gullum
kaiser -> throttle II also from gullum
soft and hardspl both phones, everything done under viste home premium 32bit.
no probs at all
Click to expand...
Click to collapse
Do you have a G3 Prophet?
I have a G3 and the radio rom install didn't work.
nope, I have a G4 and still the standard shipped radio rom
I have just tried to install gollum's rom on vista business 32bits, and the installation crashed.
ok, I've found this : http://forum.xda-developers.com/showthread.php?t=313001
I'll try and tell you if it works.
babinskyo said:
which virtual machine do you use?
I am running xp on VirtualBox 1.6.4, and i can't flash my qtek s200.
I have configure 1 filter to all my use usb devices.
When i connect my phone, it synce with active sync, but when i run the rom installation program, when my phone displays the bootloader, virtualbox tolds me that it "failed to create a proxy device for the usb device".
Can you tell me how you did?
Note : sorry if my english is aproximative.
Click to expand...
Click to collapse
I use vmware server 2 RC1 with a xp appliance, it works nice and easy.
babinskyo said:
ok, I've found this : http://forum.xda-developers.com/showthread.php?t=313001
I'll try and tell you if it works.
Click to expand...
Click to collapse
I've tried the driver and it does not work.
Thanks for VMware, i didn't knew the server version was free. I'll try it.
Flashing G4 Prophet with VMWare works well.
Thank you both, i've just tried vmware and it works !
vmware is the only way for me anyway to flash in vista. i'm sure it's the same for most of us.
don;t know how other people got the other way i.e old drivers etc to work...
Mmmmh, I think I should be thankful that my update didn't brick my prophet and the kaiser from my friend.
When the update fails on your pc is that always at a certain point ?
Do you have USB 2.0 connections and is legacy support in the PC BIOS disabled ?
Just asking for interest.
Hi Guys.
I just got a Fuze after waiting since June and I'm proud to say it's my first smartphone. So I wanted to put a cooked ROM on it and I figured out that I need to use Hard SPL for any ROM.
When I go to update the ROM with Hard SPL it goes to the progress bar on my computer and the device starts the enterbootloader.exe program. However, the second that enterbootloader.exe starts and the device goes black, I lose my connection to my PC. What am i doing wrong?
Thanks
Dan
Which OS?
What OS are you using? It my not have any significance, but with my old AT&T 8125 (HTC Wizard), I could only successfully flash my ROMs using ActiveSync with Windows XP.
Every time I would try to do it with Mobile Device Center in Vista, I would lose connection as well. I don't really use XP anymore, so I now use VM Ware to boot virtually to XP whenever I flash my ROMs.
I'm using vista, and when I installed Hard SPL I ran the SSPL (Soft SPL) and it did make my screen black. However, windows still picked up a different driver and I was successfully able to write the HardSPL while the screen was black.
im using windows 7 so that may be the problem lol