Hi, who has problems with his Bluetooth headset after the WM6 upgrade?
My Bluetooth headset used to start looking (by beeping) for the last connected device when I power it on. It doesn't do that while paired with my X7500 WM6. It does start looking MANUALLY when I press the call button on the headset and when it's connected (you see the headphones icon in the phone screen appear), it only stays that way for a few seconds. The headphones will disappear again and the connection has been lost.
When I then push the headset call button again, it starts looking again, connects again, and then disconnects again after a few seconds.
I first thought it was the headset, but it works just fine on all other devices I have, but just not the X7500 anymore. I'm sure it has something to do with the WM6 upgrade, because it was working the proper way while running WM5.
Any tips or suggestions??
The icon disapears, but calls still go through to it when they come in for me.
Have you checked to make sure it doesnt actualy work when an incoming call arrives? the icon is misleading.
No, the connection is lost when the icon has been disappeared, because the headset will start reconnecting/looking for the device when I press the headset call button.
If it was still connected it should initiate the voice speed dial.
strange, i have many headsets and dont have that problem with any.
I do have it randomly stop talking to the headset at all, and require a delete/repair, (one headset still wont connect, but i think its a crap headset issue). but when paired, they normaly behave afterwards.
Im on wm6 btw.
BUMP. This has been happening for me since my WM6 upgrade.
HBH-PV720
AMEO with HTC WM6
Please can anyone can help with this ?
DiGRem
Delete and pair
I have had issues with several Nokia phones when upgrading firmware. The other bluetooth units, previously paired with the phone, still thinks that they should be paired after the upgrade. Only issue is that the phone has totaly forgotten of all paired devices. This resulted in many connection errors, when the peripherals wanted to connect, but the phone refused. Can you somehow reset the headset? Delete the pairing on the phone, pair the headset with another phone/pc, and then, re-pair it with the athena again. Just to make sure that it has no old pairing info.
-Johan
Hello,
I have DCD 3.0.4 and Radio 3.42.50 on my xv6800. This setup connects to my car via bluetooth for audio and phone. However, when I walk away from my car and break the bluetooth connection, my phone volume is "off" and I am no longer aware of incomming calls. I always have to remember to put my volume control back to "on" after I walk away from my car.
Does anyone know of a fix for this?
Having trouble with bluetooth and my sg4. The bluetooth pairs fine but defaults back to the phone speaker when I get a call. The bluetooth headset eventually connects but it takes about 30 seconds. Anyone else having this problem?
dlscott1111 said:
Having trouble with bluetooth and my sg4. The bluetooth pairs fine but defaults back to the phone speaker when I get a call. The bluetooth headset eventually connects but it takes about 30 seconds. Anyone else having this problem?
Click to expand...
Click to collapse
I've seen some strange behavior widen paired with the Bluetooth in my Jeep Wrangler (UConnect) and with my Jawbone Era.
In the jeep, when I dial by name, it starts dialing, makes the connection and ends the call. If I dial from the phone, the call connects and seems to stay connected. I did a few hour-plus long conference calls where the Bluetooth connection to the jeep seemed to drop and I had to re-select the headset button on the phone app.
I haven't tried dialing by name with the jawbone, but I had one long running call where I had to reconnect to the jawbone.
Hi, I have a problem with my Mate 10 Pro. Every time I use my car's Bluetooth, I can't hear voice on incoming calls unless I switch to the phone speaker and then again to the Bluetooth system. The same goes for music as sometimes it switches randomly to the phone speaker and then I have to disconnect a2dp in my car and connect again. This is really annoying and frustrating. Any ideas how to solve this? Never had any Bluetooth problems with my previous phones.
After a successful bluetooth connection (Audi Q8), the call sound is not from the car by default, but I always have to manually switch it to blueooth in call settings on ZF9. Even if I select the bluetooth sound on the phone during the first call, I have to do it again during the next phone call. It also happens when I make a call through the car display.
I tried pairing again several times, changing the bluetooth name of the phone and car, unsuccessfully. The problem persists and it is quite bad.
Does anyone have a similar issue? Or an idea for a solution?
Thx