I have installed WM5SE_4 on my Wizard G4 and it works great. I would now like to try TNT, but when I try to install it, I get ERROR 300. I have tried to reinstall the Cingular ROM, but I still get ERROR 300. I installed hard_SPL-G4, before I installed WM5SE_4. What do I have to do to change this ROM to another?
Replace RUU in the TNT rom with 'MUNS_RUU' or copy and paste nk_nbf folder of TNT rom in MUNS_RUU folder and run the RUU of the MUNS_RUU.You can get the MUNS_RUU from the HardSPL thread.
zabardast_1 said:
Replace RUU in the TNT rom with 'MUNS_RUU' or copy and paste nk_nbf folder of TNT rom in MUNS_RUU folder and run the RUU of the MUNS_RUU.You can get the MUNS_RUU from the HardSPL thread.
Click to expand...
Click to collapse
Wow!! That was slick. Thanks alot!
jphuffs said:
Wow!! That was slick. Thanks alot!
Click to expand...
Click to collapse
Thanz
You are welcome !
I changed ROM on my G4 Wizard to a TNT, then added cube and baterry status for speed it up a little. It was running OK.
It blocked some time after and I am not able to load a ROM again. After reading a lot on foruns I tried Wizard lobe, 5buttons the original ROM and, after 100% loading procedure, the Wizard blocks on the very first page with the IPL 2.21.0001 e SPL 2.21.olip and that is all. I always have to start on the bootload screen (3 colors screen).
I read that as long as I can access the 3 colors I am not bricked.
can you help me?
Tks in advance
GBADCC said:
I changed ROM on my G4 Wizard to a TNT, then added cube and baterry status for speed it up a little. It was running OK.
It blocked some time after and I am not able to load a ROM again. After reading a lot on foruns I tried Wizard lobe, 5buttons the original ROM and, after 100% loading procedure, the Wizard blocks on the very first page with the IPL 2.21.0001 e SPL 2.21.olip and that is all. I always have to start on the bootload screen (3 colors screen).
I read that as long as I can access the 3 colors I am not bricked.
can you help me?
Tks in advance
Click to expand...
Click to collapse
Yes ! as long as it gets into bootloaders (tri color) its safe,but DON"T ever flash a Button's Rom onto it,as its a G3 rom with G3 IPL/SPL,it'll certainly Brick it, if it still goes to bootloaders,I must say you are a lucky guy,it didn't get bricked as you flashed Button's on it.
You must have overclocked it too high thats why it got stuck.Now as it goes to bootloaders and its HardSPL (IPL 2.21.0001/SPL 2.21.olip) flash wizard_love rom,hope it'll recover back,after that flash any wm6 rom of your choice,but don't overclock it too high.
zabardast_1 said:
Yes ! as long as it gets into bootloaders (tri color) its safe,but DON"T ever flash a Button's Rom onto it,as its a G3 rom with G3 IPL/SPL,it'll certainly Brick it, if it still goes to bootloaders,I must say you are a lucky guy,it didn't get bricked as you flashed Button's on it.
You must have overclocked it too high thats why it got stuck.Now as it goes to bootloaders and its HardSPL (IPL 2.21.0001/SPL 2.21.olip) flash wizard_love rom,hope it'll recover back,after that flash any wm6 rom of your choice,but don't overclock it too high.
Click to expand...
Click to collapse
I guess you are rigth. I overclocked with the allowance to float the frequence and did not set an upper limit.
The problem now is - I can get to the bootloader, start RUU flash procedure ( it goes slowly to 100% as usual) and reboot. After that all I can get is the HTC start screem and the wizardlove (the blue image) or TNT Series image without the radio data. It does not move forward to any other action.
With a soft reset it gaves me the HTC and the same image but with the radio data. Before asking I spent a lot of time searching in forum but I did not got to a similar problem.
Many thanks for your support.
Try a Hard reset and remove,if any sdcard or minisd.As it's HardSPL,you cannot flash an official rom also,coz it contains ipl/spl in it,Official rom is only possible after removal of HardSPL,the only way out is to have a working OS on the phone,try to flash any custom build wm6 rom.
Dear Zabardast_1
I tried to flash TNT, Qtek and a brazilian local operator ROM and no way. It always, after the 100% loading, boots and remains on the first screen.
With Farias ROM the same happens. It freezes with the first logo loading WM.
The hard reset shows formating FAT and fail to format.
Do you have any other idea?
Tks for your support.
Related
no my phone wont reboot at atll it turns on goes to a screen that says htc smart mobilty test only not for sale and in red below that it says no radio and doesnt go any further!!!!
please help me like seriously its not even my phone i need to straighten it out for him asap!!!!! i will even pay if some one can help me
press the power + camera + reset, load in the rom and radio, no need to pay, we're here to help! What is ur bootloader anyway ? is it unlock, stock rom ???
is that it because its not working is there any other method of hard reset?
i tried the buttons its not getting to the boot loader like at all , its unlocked using the titan unlocker and its just not booting up to any thing just that screen and the rom was 2.17 orignally then i flashed it to dcd's newest rom 2.2.1... then i steped it down to dcd 2.20 then i tried to flash the sprint 3.16 recent rom update and it got stuck at boot loader which was the oli bootloader which i think its called and i had to use exit_hbl and now its stuck. it will reboot but i still get that screen i mentioned before
i got to boot loader its says
TITA100
SPL-1.20.olipro
no wonder, you didn't follow instruction carefully, when you press power + camera and press reset , it should take you to tricolor, at that you can reload your sprint stock rom. Your phone is not brick yet
i just PMed you with my paypal info. Ill make sure your phone makes it out ok
thanks but if anyone its astrqnusx hed get money first i flashed the rom again it worked and then i tried to flash the radio and it just restarts and doesnt load at all??? its stuck at the mobilty screen???
what radio and rom did you use? I assume that you have Titan(Mogul) not touch
and after the radio i tried to reload the rom and it acted as tho it would work and is now stuck at the mobilty and i used now dcds 1.6.8 rom and the 3.27 radio... and now its really stuck maybe i should try the stock rom for sprint?
you are too rush on thing, you can't use rom 1.6.8 with the new radio, reflash back with stock rom from your vendor to get working condition. There is specific instruction if you want to load the radio
After you get back to your vendor (sprint/verizon) follow this instruction to flash new rom, don't miss a step http://forum.ppcgeeks.com/showthread.php?t=17667. Again, I see you have the touch, touch and mogul are two different device you can't use DCD or any rom here. You have Titan Phone right?
-my touch is fine thats a custom flashed rom from swiftblade and it works amazing with a radio update ive done alot of different things even reg edits
but the titan is just new to me
Is your phone working yet?
yea i got it thanks!
I'm having the same issue, but I cannot get back to the tri color screen. Any advice? I thought I followed directions pretty well, but apparently not.
j3oomerang said:
i just PMed you with my paypal info. Ill make sure your phone makes it out ok
Click to expand...
Click to collapse
You must be a sad little man.
nismofun said:
I'm having the same issue, but I cannot get back to the tri color screen. Any advice? I thought I followed directions pretty well, but apparently not.
Click to expand...
Click to collapse
I had the same problem flashing my mogal, it's not difficult to fix. take a deep breath, it will take a little bit of work but you can do it. flash back to rom 2.17 relock, then flash sprint official rom 3.35. Then run hard spl 2.40 then flash new rom, take battery out, hard reset should fix your problem. the relocker,unlocker and everything else can be found by searching xda and ppcgeeks.com
I had the same issue, resolved:
http://forum.xda-developers.com/showthread.php?t=384298
Cheers,
Tom
Any idea? I have to QTEK 8500. One upgraded nicely to 6.1 - the other gives me Error 270 after 5% flashing.
How can I bypass this?
The wiki seems not to exist at least at the moment (timeouts on requests), so I am lost here to know what to do.
Please advice
270 during flashing
First of all - as in instructions to flashing - make sure the phone is unlocked, both aplication and the other unlock.
If it still happens then I had the same thing. I used the clean "boring" ROM. After I changed the bootloader to a newer version, I was ok. So first flash the bootloader - it must be given on the same page as the rom file, and keep your fingers crossed - 'couse if it doesn't work you are in for a problem with a brick.
It should actually take a few seconds only.
After that, flash the new rom, should be ok.
No bootloader update - where is it?
The rom is from the article at http://forum.xda-developers.com/showthread.php?t=374397
(6.1 standard).
So, tell me - Where can I Find the instructions on how to update the boot loader?
Thona said:
the other gives me Error 270 after 5% flashing.
Click to expand...
Click to collapse
is it "corrupted image" error? if yes - READ THE ****ING MANUAL carefully and make sure you have done all the steps in it
Hi,
I had the same problem as you....
My phone was correctly unlocked, but it won't pass the 5% after a first try when i went to 97% (communication error). I was stuck on the nice Erofish sun starting pictures.
I tries many times to flash with the 6.1 standard, but it won't go through the 5% limit (the phone turns off at 5% but it was fully loaded). So I downloaded all the wm6 roms available in this great forum, try to flash them but it was not working (still stick at 5%).
So I doanload a 5.0 rom (Expansys forum : http://www.expansys-usa.com/ft.aspx?k=73618) and was able to flash my phone....
Then after I tried again to reflash with the Erofich rom, and was able to do it. So now, I can use my phone again with the great rom.
Regards,
F.
is it "corrupted image" error? if yes - READ THE ****ING MANUAL carefully and make sure you have done all the steps in it
Click to expand...
Click to collapse
I did - I can redo them, but this is the second phone I try to flash What step do you think I am missing? And it IS the corrupted image error. Is the application unlock wrong?
fdecourt said:
Hi,
I had the same problem as you....
My phone was correctly unlocked, but it won't pass the 5% after a first try when i went to 97% (communication error). I was stuck on the nice Erofish sun starting pictures.
I tries many times to flash with the 6.1 standard, but it won't go through the 5% limit (the phone turns off at 5% but it was fully loaded). So I downloaded all the wm6 roms available in this great forum, try to flash them but it was not working (still stick at 5%).
So I doanload a 5.0 rom (Expansys forum : http://www.expansys-usa.com/ft.aspx?k=73618) and was able to flash my phone....
Then after I tried again to reflash with the Erofich rom, and was able to do it. So now, I can use my phone again with the great rom.
Regards,
F.
Click to expand...
Click to collapse
Thanx! it worked!!!!
Thona said:
What step do you think I am missing?
Click to expand...
Click to collapse
Soft SPL aka SSPL aka USPL
Häh? Sorry, but where is that in the original documentation? I must totally miss it. I follow the instructions in the post verbatim.
It's included in the directions. Problem is, your phone is probably Application Locked. Try running the Application Unlock, then run the SSPL.lnk. When you run SSPL, it should put the phone into a virtual "bootloader" screen. This is where the RUU will run the upgrade process. This should get you taken care of. If not, let me know, we'll see what we can get going for you.
Hello
I have the same problem but when I flash with this original rom after 5% telephon turns off and it shows error 294 invalid vender ID
Anyone helps
Somehow i made hard reset and it works now
Today I restored into my Touch Dual an Original TIM Italian ROM because with TOM ROM I can't use one exchenge certificate... I follow all the step and now my Dual is full working with the old original rom but I have a problem... On startup when the display write smart mobility and after the version of radio and ROM, the version of the ROM is a mix from the original version and the write niki projet a write like this D1iki Pro in stead of D and the code of ROM... What can I do to fix this problem? I try to reinstall 2 times the original ROM but i read always the same "error"... thanks a lot and sorry for my english
make hard reset ... ignore the splash screen
The phone works fine but I want to fix this write in the first screen because I think that would be a problem if I bring the phone in warranty
NetrunnerAT said:
make hard reset ... ignore the splash screen
Click to expand...
Click to collapse
It's not a splash screen... I read this wrong ROM number in the screen smart mobility under this write.... In red
Nobody can hel me?
make a screen shot ... i dont know what you mean ....
On the first screen image when I starup the Phone the phone write smart mobility and then in the lower part of the screen in red write the code of ROM and RADIO. When I flash the TOM's ROM I read on the screen NIKE PROJET but when I Flash the original ROM I read 1IKE PROJET and not a code of original ROM 1.31.408.09... Exclude this problem the phone work so good with the original ROM but I think that Would be a problem if I bring the phone in warranty... thanks and sorry for my bad english
I think that the problem probably is this in the picture... When I install the Original TIM ROM the version is set to 1.00.000.0... In fact in my start screen when I flash the original ROM the Only numer that overwrite the name niky projet is 1... Only a litlle help...
Flash a Full Rom, with Radio, OS, SPL and Splash screen. This clean all! Then write TIM over it!
NetrunnerAT said:
Flash a Full Rom, with Radio, OS, SPL and Splash screen. This clean all! Then write TIM over it!
Click to expand...
Click to collapse
sorry but I'm a newby with windows mobile.... where can I find a full ROM? And how can I flash the Splash screen.... Thanks a lot for your assistence....
http://www.4shared.com/file/3772442..._13170709_Radio_Nike_1581627_signed_Ship.html
start sspl and flash this rom!
so I start sspl and then flash this ROM without flash before the hard spl is it right (I've got alredy installed the hard spl) ? And then for flash a splash screen? I flash it like a ROM? Or splash sceen is inside this rom?
Just start it and flash.
I try to flash that ROM but the process always stop at 15 % with a cummunication errror... I remove the battery and the phone start with the display in 3 color mode hardspl.... where I'm wrong?
Is possible that the error is caused by the hardspl installed on my phone that don't allow to the spl of the ROM to install in the phone?
Hi everybody,
Well yesterday i figured out that i could update my rom.
I started to look the Arthemis thread to find out what's new.
I saw SSPL and the 3.14 rom.
I downloaded the 3.14 rom and i installed it.After that i took the SSPL and the Arthemis V42 Rom and tried to install it. No success.
After that i took the energy rom to install it and it works but i still have the 3.14 rom display instead of the energy rom.
So right now i'm a little bit stuck cause i don't know what to do
Here's my specs:
SPL-2.08.HSPL 8G XE
Systeme version : 5.2.21684 (21684.5.3.10)
Manila version : 2.5.20191914.0
Rom version: 09 November 2010 FRE
Radio Version: 2.12.50.02_2
Protocol Version : 15.40.50.07U
So i'm asking you guys a little help please to put energy or new arthemis back in my phone.
Thanks for your help
Ps: ( I need help on how to put my phone back to normal i'm a little confused about SSPL and the 3.14 rom :s )
run Task29
! Read Edit 2 down below first !
Well, you could try to run Task29. That will purge your ROM and leaves it nice and perfectly clean for another ROM without the risk of residua in the memory.
You can find it here:
http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19
You will need to install a radio ROM after that, too. But having the memory wiped clean this way between installs is a good way to avoid trouble.
ThoroSOE
Edit 1: To reset your phone to normal (SPL, too) just download an original ROM and unpack the file with something like 7zip. Take the largest file (easy to spot) and rename it to LEOIMG.nbh. Copy that to your freshly formattet memory card and bring up your phone to the bootloader screen (power up with volume down pressed). It will then prompt to install the original ROM. This will overwrite HSPL and any ROM and Radio ROM you installed.
Edit 2: It could be that with ROM 3.14 the SPL is too new for HSPL! Mind that it just supports specific SPL versions! Check that! I think 3.14 has an 3.XX SPL version.
Before I could install HSPL properly I had to downgrade my ROM with an older original one to get the proper SPL (see Edit 1).
Thanks i try it now ill let you know.
Sir you don't need to look fare for your problem.
The problem is that stock ROM 3.14 isn't compatible with HSPL!!
And about Artemis ROM; I suggest you to take your time and read the "How to install?" At the Artemis ROM.
If you did it; you was ale to see you need to remove HSPL before install stock ROM 3.14!
thanks kurt-willems for answering me.
Can you tell me hat i need to do step by step please ?
I will really appreciate.
Thanks for help guys.
OcmyHtc said:
thanks kurt-willems for answering me.
Can you tell me hat i need to do step by step please ?
I will really appreciate.
Thanks for help guys.
Click to expand...
Click to collapse
Sir I don't see how I can write a better step by step guide on how to do it.
I will suggest you to read these post's.
If you have a unbranded device:
http://forum.xda-developers.com/showpost.php?p=8776196&postcount=26465
Ore this in case you have a branded device:
http://forum.xda-developers.com/showpost.php?p=8945325&postcount=28077
PS; if you have random questions, follow the link at my signature "Q&A: How? Where? what? Ideas? [New Users?]"
And if your have other questions, just ask. but it is important to read and follow the institutions.
Thanks again kurt-willems for your answer.
So after reading the entire post on how to flash arthemis rom i did all the steps but i am stuck at the step 7
7. Run SSPL_RUU.exe with Artemis v40 RUU_Signed_0409.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
I did all as it is explained in the thread my SSPL is good etc but when i launch SSPL + arthemis nbh, i got into the bootloader.
I tried like 5 times and i start to be angry.
So if you can help me it would be great.
Thanks
Ok i dont have nerves to do it again, can you guys just simply explain me how to uninstall SPL 3.03 and just install HSPL 2 and put a simple rom cause right now my phone don't work because of that.
Thanks you guys for reading me.
If you will install Artemis ROM I suggest you to use v42.0!
I/we know that flashing over SSPL isn't alway's easy (it will not start alway's)
but some important things to know is to deactivate your Anti-Virus; and creating a file with only the rom.nbh and SSPL_RUU in it nothing els!
(PS; Artemis ROM v42.0 starts better than previous v41.0 (own experience))
But if you will return to previous settings;
Reinstall a previous stock ROM ex 1.66 ore 1.47 (depending of you're aria)
Reinstall HSPL use HSPL3_RUN.exe fore this.
Thank you kurt willems for your time.
So after reading a lot of things , i did everything but im still stuck at the installation of the arthemis rom.
I got a message in the phone saying: This program is trying to acces to your phone etccc... Bootloader.exe. And if i say YES then the program launch bootloader and the installation fails. If i say NO then the program stops.
I'm downloading right now the version 42 of arthemis and i will give it a try.
If its doesnt working then i'll rollback to my previous rom.
Thanks again for your time.
OcmyHtc said:
Thank you kurt willems for your time.
So after reading a lot of things , i did everything but im still stuck at the installation of the arthemis rom.
I got a message in the phone saying: This program is trying to acces to your phone etccc... Bootloader.exe. And if i say YES then the program launch bootloader and the installation fails. If i say NO then the program stops.
I'm downloading right now the version 42 of arthemis and i will give it a try.
If its doesnt working then i'll rollback to my previous rom.
Thanks again for your time.
Click to expand...
Click to collapse
I know this event sir, I have guide lot of users in this part. When you are on the bootlouder screen and at the bottom there is no mention of "usb" the installation will fail.
Its very important to be sure that your device is connect (control it in Active sync), Anti-Virus is turn off, the folder have only the rom.nbh and the SSPL_RUN (nothing more) in it, changing from USB port if you can.
And don't double click on SSPL_RUU fore run, but left click on it and select run ass administrator.
Lately I guide a other user on this and it have takes him 5 tray's
Ow, to be sure you have a good SSPL_RUU version takes mine: Download
Thanks but right now i just want one thing.. My phone to work.
I downloaded V42 and still the same problem.
I downloaded stock rom V1.93 from orange and i can't install it , don't ask me why.
So right now basically my phone is on the stock 3.14 rom and i don't know what to do to put an old rom and to flash to a energy rom with HSPL 3.
Seriously this all thing start to piss me off , no offence guys you making good stuff but sometimes its just to risky to flash.
I followed all the steps one by one and right now i got a useless phone in my hands.
I'm searching a way to get an old rom to be installed and desinstall SSPL.
If you can help me it would be great , im still searching.
You can flash a older stock ROM over SD.
Read my first post. There you can read how to reset to stock (Edit 1). Use an older stock ROM for a proper SPL that works with HSPL.
Install HSPL as instructed in the "how to flash everything" thread.
Run Task29 (see my first post)
Install Radio ROM with x.50.x in it from desktop via Active Sync (you need a Custom_RUU.nbh and the desired Radio ROM).
Install the main ROM you like, f.e. Energy ROM (that's what I use) normally from destop via Active Sync (Energy is one package that works like an official update).
Never had any problems with this way, never needed more than one try.
Hey ThoroSOE i rode Edit 1 and Edit 2.
I hope its not that much to ask but, could you give me a WWE rom like you said in Edit 1 to put it in the SD card ?
It would be really appreciated.
I'm downloading right now a official orange rom (1.66) but i tried installing the 1.43 and it didnt worked, thats why i'm asking you the question for a WWE rom to accomplish what u told me on Edit 1.
Thanks you guys for helping me.
Ok i'm trying this right now Edit 1: To reset your phone to normal (SPL, too) just download an original ROM and unpack the file with something like 7zip. Take the largest file (easy to spot) and rename it to LEOIMG.nbh
With the 1.66 official rom.
I will let you know.
Ok so i tried to do what u told me on edit 1.
I enter in bootloader and what i get is a nice :
Loading ...
Then
00028002
Not Allow
Can someone can tell me how to uninstall SSPL >?
Cause i really start to go crazy
OcmyHtc said:
Ok so i tried to do what u told me on edit 1.
I enter in bootloader and what i get is a nice :
Loading ...
Then
00028002
Not Allow
Can someone can tell me how to uninstall SSPL >?
Cause i really start to go crazy
Click to expand...
Click to collapse
SSPL isn't install on your device! so there is no need to remove it.
Did you tray to install stock ROM over SD!?
Witch are your errors you get?
Hmmm. Installing an official ROM from SD card shouldn't be a problem. If you have a branded device you should install an official ROM that matches your provider and area. For later purposes like installing HSPL it doesn't matter how old it is - as long as it is not too NEW ;-)
That way of installing a ROM (via SD card) ist kind of the brute way. As long as you use a ROM matching your provider and/or area it should overwrite ANYTHING in your phone memory...
When I unsintalled HSPL for the first time that way my HD2 aborted the update in midprocess but restarted updating automatically. After that it went through without problems; I didn't have to do anything.
I used the official 1.66 ROM from the HTC support page (unlocked device).
IMPORTANT: Did you name the ROM file for the SD card LEOIMG.nbh - in all capital letters? As I understand it, the bootloader is case sensitive. So it must be LEOIMG and not leoimg. Also did you format your SD card properly? It must be FAT 32, 4092K - and better not be done with quick formatting.
OcmyHtc said:
Ok so i tried to do what u told me on edit 1.
I enter in bootloader and what i get is a nice :
Loading ...
Then
00028002
Not Allow
Can someone can tell me how to uninstall SSPL >?
Cause i really start to go crazy
Click to expand...
Click to collapse
kurt-willems said:
SSPL isn't install on your device! so there is no need to remove it.
Did you tray to install stock ROM over SD!?
Witch are your errors you get?
Click to expand...
Click to collapse
As you can see in my post i already tried to install threw SD card.
When i enter in bootloader (vol down + boot the phone)
I have:
PB81100 HX BC
SPL- 3.03.0000 XE
So i have SSPL in my device.
ThoroSOE said:
Hmmm. Installing an official ROM from SD card shouldn't be a problem. If you have a branded device you should install an official ROM that matches your provider and area. For later purposes like installing HSPL it doesn't matter how old it is - as long as it is not too NEW ;-)
I have the orange operator in france.I took the version 1.66 put it into the sd card like you said.
When i pressed Vol down + boot to go into bootloader i get the error message:
00028002
Not Allow
That way of installing a ROM (via SD card) ist kind of the brute way. As long as you use a ROM matching your provider and/or area it should overwrite ANYTHING in your phone memory...
When I unsintalled HSPL for the first time that way my HD2 aborted the update in midprocess but restarted updating automatically. After that it went through without problems; I didn't have to do anything.
I used the official 1.66 ROM from the HTC support page (unlocked device).
IMPORTANT: Did you name the ROM file for the SD card LEOIMG.nbh - YES
in all capital letters? As I understand it, the bootloader is case sensitive. So it must be LEOIMG and not leoimg. Also did you format your SD card properly?
I format my SD card by the format option on the HTC leo.So i don't know if it's the good way to do it ?
It must be FAT 32, 4092K - and better not be done with quick formatting.
Click to expand...
Click to collapse
Please guys help me out i really don't know what do to anymore..
Obsolete
see http://forum.xda-developers.com/showthread.php?p=19893221#post19893221
id\ did it and my mobile now dont make any response to any kind of action i cant even open it boot it or any thing
noooooooooooooooooooooooo
did you have a stock rom or custom one before flashing ? how did you flash it?
thx in advance
i was using latest stock rom of my country (middle east)
but i used the spl flasher but changed the file with the link in this forum and then every thing went black i cant even press volume down to install a rom or boot any thing cant even charge my mobile
warning
pls dont installllllll my phone is completely brick dont installl people
i swear my phone is now completely brick down
Flash back hardspl or your backup
The old SPL file was corrupt, the first post is updated with a working new SPL.
How to flash this to my phone?
I tried via rom update utility but it can not read the file.
[edit]
obsolete message
Thanks.
This file works with rom update utility.
Great.
Did you find any difference with SPL 1.28 other than the charging animation?
so far no.
You sure that this working? i have flash it 3 times on my phone but still on info is "SPL 1.28"
VirusPlus said:
You sure that this working? i have flash it 3 times on my phone but still on info is "SPL 1.28"
Click to expand...
Click to collapse
Do you have 1.28 HardSPL or stock 1.28?
You should probably flash HardSPL first
I have 1.28 HardSPL, not stock one. I reflash HardSPL tho but still nothing
I'm searching for a way to fix this.
Will keep you posted
[edit]
obsolete message