Related
Hi,
I have Qtek 9100 with IPL 1.01 and SPL 2.20.0001. When I switch on divice, it displeyed color screen and nothing more. I flash it whit many ROM's but IPL/SPL always is the same and did't work normal. How can I resolve the problem. Thanks!
Only with a JTAG device. It's a special device that can access the chips without the need for the phone to be working. But nobody knows which are the JTAG pins so no luck here.
The IPL 1.xx is meant for the G3 DOC chip Wizards and G4 all have IPL/SPL starting at 2.xx.xxxxx. Since IPL is the firt bootloader with information and addresses for SPL and since they don't match you'll never get out of that situation...
Thanks for reply. I have JTAC device and will try to find jtag pinouts for Wizard G4.
havy said:
Hi,
I have Qtek 9100 with IPL 1.01 and SPL 2.20.0001. When I switch on divice, it displeyed color screen and nothing more. I flash it whit many ROM's but IPL/SPL always is the same and did't work normal. How can I resolve the problem. Thanks!
Click to expand...
Click to collapse
Try..
(1) put the phone in bootloader mode
(2) flash it with cingular 1.x radio (search for it)
you should get a normal device in the end
best of luck!
dont know how
kdskamal said:
Try..
(1) put the phone in bootloader mode
(2) flash it with cingular 1.x radio (search for it)
you should get a normal device in the end
best of luck!
Click to expand...
Click to collapse
(1) OK
(2) DONT KNOW HOW!!
Please help, i never did this. how do i flash the phone if my comp does not recognise it (i can only enter the bootloader screen).
You should
1) Flash only IPL/SPL from g4 (f.e. 2.26.0001) to get your SPL/IPL the same with italian RUU 2.5.2
2) Flash ROM without IPL/SPL italian RUU 2.5.2
yesterday we bringed such device to live) try
how do you compare that with Atom
Hi,
I have got O2 Arom.
does anyone know whether my device is equivelent to G3 or G4?? or its completely diff technology that cannot be compared!!!
I know O2 Atom is by Quanta and it uses CPLD (Complex programmble Logic Design!! I hope i remember this right).
this can't be compared at all, totally different technology. there is a whole separate section for the atom. just go to the forum root page and look for the atom.
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
koorosh_bsboys said:
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
Click to expand...
Click to collapse
Did you also read the wiki to see how to install hardspl to protect your device BEFORE flashing ?(here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27 )? Are you using Olipro hardspl?
Try to use the SDCARD method (Format a sdcard in FAT32. Copy the nbh file on it and rename it HERMIMG.NBH. Insert the card and HR : OK/POWER/Soft reset. Follow the instructions)
i tested that but didn't help
does anybody have any suggestion??
Try solution to reeboot ( sometimes helps)
1. get out SIM and SD card
get mtty http://forum.xda-developers.com/download.php?id=9864
2. Make BL mode on Hermes
2a on PC ActiveSync - coonection properties untick allow to connect by USB
3. start mtty on PC , choose USB and enter.
4. next enter.
5. type set 14 and enter
6. type task 8 and enter
OS have to boot if no go to 7
7. enter
8 type set 16 and enter
9. type task 8 and enter
Hope that will boot
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Pretty much all the info on unbricking is in this table by Pof. If this doesn't sort you out then you're have to send it off to imeicheck etc for repair.
The history so far
I have bricked my jasjam while updating to telstra wm6
I have not super CID my device before upgrading to telstra wm6
Now my device freezed at second splash screen
IPL 1.04
SPL 2.03
NO GSM
when i used the info 6 command on mtty it says NO CID
i can not upgrade my device from SD CARD (memory stick)
i used these command on MTTY.exe but no improvement
set 14
task 8
set 16
task 8
when i tried to rom upgrade using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
any suggestions????
I hope you understand this, Basically if
1. You have a "No GSM"
2. Your CID is corrupted
3. Your OS has no KITL mode
4. You didn't use HARDSPL...
Then your phone is screwed, and you need to buy a new one or send it to repair.
Hope you have better luck with your next phone. (you seem to be collecting bricked phones!)
Wam7 said:
4. You didn't use HARDSPL...
Click to expand...
Click to collapse
That's the BIGGEST mistake u ever made with ur Jasjam, bro
try to send to repair centre, if repair cost is too much. Than u have to decide try but new gadget. Kaiser looks flirt to me
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
st3v3 said:
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
Click to expand...
Click to collapse
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
ermenzegna said:
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
Click to expand...
Click to collapse
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
st3v3 said:
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
Click to expand...
Click to collapse
This has NOTHING to do with only using official Roms! One has pretty much the same chance of bricking their phone evening using an official WM6 as a cooked variant from Schaps et al..
Simply put if you don't use HardSPL then you're asking for trouble no matter what the ROM. You should also use the MicroSD wherever possible as it is much more reliable.
imei check use jtag to fix this
imei check use jtag to fix this ,CAn we use jtag to fix this in hermes. need help to resovle spl 2.03 cid locked no gsm.
MTTY's "wdata" cmd unlocked on SPL 2.03!Can it Unbrick the bricked ones w SPL 2.03??
I have found a way to unlock "wdata" command in bootloader 2.03!
summary:
In bricked hermeses with SPL 2.03 - NO GSM - KITL disabled, the wdata command is locked. I am not good at programing but I want to know if it possible to change the SPL(bootloader) of bricked hermeses with this command in mtty.exe??!!
How to:
1.Use the trinity splxploit -windows by pof (unbrick.bat). Let the program run for some seconds and then just close that.
2.Do not unplug the usb or soft reset the device.
3.Run mtty.exe and type "wdata" the command is unlocked!
I wanna know can we erase just the CID by erase command and write a CID value using wdata command?
If it can be done then we can unbrick our hermeses!
Yes it enable wdata, you don't need to change CID, if you can load OS.nb, then from Windows use SSPL. But real problem is how to load OS.nb via wdata
need Hermes splxploit -windows ??
i many time write in this forum who can unbrick hermes with spl 2.03 cid locked,no kitl,can not boot,stack in bootloader....only solution is that pof
or good man create Hermes splxploit -windows this will jump spl address and temporaly cid unlock Hermes then we can flash any rom.
I unbrick many Trinity bat wait solution for Hermes???
Bat wait ........and wait.
Zemo znas li ti kako da sredis brikovan hermes cid zakljucan spl 2.03...itd.
Yes, we need pof help, it will be very good to have spl exploit for hermes.
Bas nas dosta ima na XDA, mozes samo preko JTAG koliko je meni poznato ali neznam nikog ko to moze da uradi. Odakle si?
Yes, we need pof help. It will be very nice to have SPL exploit.
Mislim da moze preko JTAG, ali neznam ko to moze da uradi, odakle si?
Bad news people,
The memory layout on hermes is different than on trinity, i already looked
into this and is not possible to exploit it in the same way as I did in
trinity.
I am sorry but I have no time to invest on this now
Best Regards,
pof
Click to expand...
Click to collapse
We can wait for pof, and pray
So, we will wait.......!
I'm a prayer too
So, we will wait.......!
I'm a prayer too
Reply With Quote
Click to expand...
Click to collapse
MY HERMES IS BOOTED OS TODAY!!!
It was half dopod and half T-Mobile...
T Mobile Customanisation: Instalig Dopod stuff???
I soft reset it and it stuck again.
Booted OS
Today my hermes booted os, after soft reset it stuck again. But there is hope, right?
Can you solve No GSM with SD Card Flash?
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Yes, I know that.
If you have similar problem:
1.Leave Hermes without battery for some time, hour or so.
2. DO NOT turn it on, do a HARD RESET*
*If don't work try several times
hardspl v7 or any other after 100% message image corupted
koorosh_bsboys said:
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Click to expand...
Click to collapse
Yes i know this bat this will not work if hermes cid locked and stack in bootloader no kitl and gsm.Can not boot os this only work in hermes cid unlocked device then sd card work...bat what i can do when device cid locked and can not connect in activsync and everytime when try to use hardspl v7 or any other after 100% message image corupted only solution is that pof create jumpspl pach that work from dos without activesync this can help me and many other i will donate with paypal if somebody can creat this that work in hermes......
............again harmes how to unbrick 2.03
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
If somebody else create solution before me please sent me message to know??
Do not post any solution from this site i try all and not work(SD card will not work when cid locked,hard spl-not work always 100% then message image corrupted,No kitl.....so please only original solution not from xda-developers..etc.
thanks for all.
Pozdrav zemljacima iz Srbije.
Pozdrav,
Ima nas prilicno sa SPL 2.03...
Igor
gsmhackerns said:
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
....
Click to expand...
Click to collapse
Glad to hear that.
I am sure that the sulotion for spl 2.03 exists, but we don't know where to find it.
BTW, where is POF & olipro????
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
igord said:
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
Click to expand...
Click to collapse
My hermes can't boot into OS. It has stucked on 2nd splash screen (Imate telstra logo) not the OS logo!
How can u boot into OS?
If you find something new then share it with us.
My HERMES sometimes stuck at second boot scree and sometimes at windows screen, but few times it booted os. Than I put SSPL at microSD, becouse it stuck after few sec when it is on USB. OS is working ok - then I killed it again to SPL 2.03 and today get it back to working OS, No GSM.
What I did to get working OS???
1. Get battery out for about a day.
2. Put the battery in, DON'T POWER ON!!!
3. Do a HARD RESET.
If it don't work try several times.
Hi
I have qtek s200 never locked on any network
I have downloaded ROMUpdateUtility_NV_G3 and G4
But after i done to see 3 colors i have doubt i what G3 or G4 update rom to use
IPL 2.09
SPL 2.09.0000
gsm 02.07.20
os 2.9.7.24
My question is which Rom to user G3 or G4, or i have to do something more before runing RomUpdate
tnx in advance
By this link
http://wiki.xda-developers.com/index.php?pagename=prophet_g3g4_how
It might be G3
but not sure because my IPL 2.09 without anythin after that .09
but with 4 zeros after.09 in SPL
that is normal "fake boot", freezed screen because you didn't make the HardSPL,
yes, its a G3,
read my thread..... read man, read post 1 is ok
enjoy
dioxda2 said:
that is normal "fake boot", freezed screen because you didn't make the HardSPL,
yes, its a G3,
read my thread..... read man, read post 1 is ok
enjoy
Click to expand...
Click to collapse
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Bakudan said:
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Click to expand...
Click to collapse
1. "old method" for "old roms"
= Flash PVtemp (everytime), then upgrade wm6 (must follow my steps.......in my post),
2. "new method" for "new roms"
= Flash HardSPL (only needed once), then upgrade to wm6 or 6.1
ok now?
Bakudan said:
That's the case
I didn't do anything. This is factory setup
This is never locked on any network Qtek . it works 100%.
I just want to upgread it to WM6
Click to expand...
Click to collapse
That iS the point! You HAVE to prepare your S200 first before you can upgrade to WM6. With only factory defaults you are NOT able to succeed.
So I second dioxda2's advice:
read all the guides, WIKI's and other relevant information here before you dive into the deep... But hee, afterall its your phone....
rondol1 said:
That iS the point! You HAVE to prepare your S200 first before you can upgrade to WM6. With only factory defaults you are NOT able to succeed.
So I second dioxda2's advice:
read all the guides, WIKI's and other relevant information here before you dive into the deep... But hee, afterall its your phone....
Click to expand...
Click to collapse
So if i download gullum ROM Prophet XB
First to do ROMUpdateUtility_NV_G3.exe
and after that Upgrade_ROM.bat
if i get it correctly
i did hardspl
and after i'm trying to install touchXB i get
Copying C:\DOCUME~1\MARKO~1.TEK\Desktop\QTEK\PROPHE~2\itsutils.dll to WCE:\windows\ItsUtils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
tryed restarting device and ms sync
i get the same stuff
Bakudan said:
i did hardspl
and after i'm trying to install touchXB i get
Copying C:\DOCUME~1\MARKO~1.TEK\Desktop\QTEK\PROPHE~2\itsutils.dll to WCE:\windows\ItsUtils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
tryed restarting device and ms sync
i get the same stuff
Click to expand...
Click to collapse
this is a common error when the pathname is to long. Copy the Folder to your rootdirectory (C:\) of your PC and run upgrade.bat from that location.
tnx
this time everything went OK
i enters setup set up password and now is not ok..
it wont accept it
Bakudan said:
tnx
this time everything went OK
i enters setup set up password and now is not ok..
it wont accept it
Click to expand...
Click to collapse
That too is a common problem, with this version of WM6 password just don't "stick". The problem is with all WM6 ROM's of that generation, not only the one you flashed. There is no solution, just don't use a password. The newest ROM's seem to have solved this issue, but I can't confirm that because I don't use a password anyway.
So, now you are stuck. Do a Hard Reset and configure your device again.
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?