Related
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor
nbhor said:
Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor
Click to expand...
Click to collapse
You are right, this has been asked a number of time... . May i suggest another method to load your rom?: SD card. You do not need to use a USB connection (no risk to loose it) nor a PC and it works perfectly.
1> format a sdcard in FAT32 (use a card of max 2GB)
2> copy the .nbh file to it (Preferably the only file on the card)
3> rename the file: HERMIMG.NBH
4> insert the card and push: OK-POWER-SOFT RESET (to go to the 3 colors screen). It will detect your hermimg file (says "loading" in blue) and describe the content
5> follow instructions on screen.
And that's it ! Just note that flashing a radio rom is slow. This means that you will have the impression that it stops time to time. Just be patient
Oh... by the way, having tried nearly all radios available, 1.47 is for me the best compromize between battery drain and performances (at least in my area). But, once again, this is a matter of taste. Make your religion
Thanks a lot. Actually I have followed the same process while upgrading from WM5 to vp 3G's WM6. But I was not aware that I can use same process to upgrade the radio only. And to my surprise it worked like a charm. Appreciate your help in this matter. I will update you with my experience on this radio version.
Thanks -nbhor
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
As far as you can still flash, the method explained above should work
terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
Hi Glenn this happened with me for couple of times too. Didn't ask anything in boot loader.Then I went back to board and did as this thread says http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing and this helped. May be this will help you too. All the best.
Thanks -nbhor
Hi nbhor,
Thanks for that, I had read that thread but not stressed much about preparing the cards, a format and error check (which ti my amazment found bad sectors on two brand new transflash cards sorted it and it now tries to flash but still fails unfortunately. Oh well looks like no radio for me again :-(
Cheers Glenn
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
do you happen to have ftouchflo cooked in somehow? if you have ftouchflo running, it wont let you calibrate the screen (for me at least).
JonnyBoy313 said:
I got the mogul, and when I run any dcd rom Its loops to the welcome then restarts. Tried relocking, then unlocking (with olp 2.40)
I tried to install the rom first (dcd 2.2.0) then 3.27 Radio(off SD card cause wouldnt reboot)
Then I tried The 3.27 radio first, then 2.2.0 rom same thing(restarts at welcome screen)
SD card flashed back to 2.17 Sprint official, with 1.47 radio(works fine every time)
also tried it on dcd 2.1.0, and 1.6.8 all restarted in a loop,
Anyone have any suggestions on how to fix?
Or does anyone else have a good stable wm6.1 with htc touch UI rom maybe with 3.27 radio included?
I am a noob but im am starting to get this thanks for your help
Click to expand...
Click to collapse
The same thing happened to me. The only way that I could get past that issue was to wait about 5 minutes until I started to calibrate the screen. It then worked..... but it would then reboot in a loop when i tried to open Activsync to configure my exchange server. (And no, I didn't have touchflo enabled).
I went back to 3.16 and it works fine.
Make sure your Olipro 2.40 unlocker took correctly. If it did not, then you will get reboots exactly as you described.
Also, did you do a hard reset after installing your latest ROM?
Hard-SPL did not install correctly... This happened to my phone as well.
Rom restarts right after welcome screen
Ill i am about to try that again, but the flash made me lose the ESPT settings.
Now I cant make any calls. I wrote all settings down , but I do not have the Unlock code, And I cant find it, (ITS NOT 000000)Running a mogul.
the reboots are because you didnt unlock correctly.
i had the same problem, i had the new rom flashed but the phone wasnt unlocked right.
you have to run titanunlocker.bat first, follow the instructions then your boot loader should show 2.40.
as for the ESPT settings, you can get the unlock code by using the attached.
your ESN hex is what you need to input to the keygen.
should be under your device information, in your settings.
Roms restart right after I tap the the Welcome
Ok I locked it again, Loaded a fresh official 2.17. Connected to activesync unlocked again, loaded a DCD 2.2.0, then 3.27 radio, restarded,set it all up,
got to page with start tab(home screen) Then starts to restart( at the same point). Maybe I dont Have the right unlocker it says 2.40(when i open with winrar)
Thanks, im very new at this but you guys have help me all the way through.
I have successfully recovered my phone in every way possible. I mean every way. But still havent seen a rom work yet. I feel like IM close though
Roms restart right after I tap the the Welcome
The Spf unlocker that ive been running does not show 2.40 in bootloader after unlock, only 1.10. But when I open it with winrar I can see the olp2.40
should i look for a different one
When I load this spf on phone, from home pc the unlocker says if you see 1.10 unhook usb then reconnect
Roms restart right after I tap the the Welcome
maybe Im not understanding how to do a hard reset a hard reset
thanks for the spc getter worked perfectely
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Your phone's cdma. This is a gsm forum. I'm assuming that you're trying to brick your phone with the gsm hard spl and not trying to flash the proper hard spl. Stop doing that, your phone is getting pissed at you. Go to ppcgeeks or the cdma (Herman, not Raphael) forum here.
haha leave it to me to find the wrong way to do something. I appreciate your heads up Ted!
rceubanks said:
Hey guys...sorry if this has been covered. I tried searching the forums and can't seem to find anything on it.
All of the roms seem to be plug it in, install it and BLAM, you're ready to go.
My issue is that I get a communication error everytime I try to install any roms or the HardSPL. The exact error given is "The ROM Update Utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the error so you can continue with the update."
While performing the updates, I hear the sound as if my USB disconnects, then it reconnects after it restarts into the multi-colored screen. It shows "Security disabled" at the top of the screen. It proceeds to the loading bar and just sits at 0% until it comes up with the disconnect screen.
I'm using the HTC Touch Pro running WM6.1 on the Sprint network.
Again, sorry if this has already been discussed, I just couldn't find anything on it.
Click to expand...
Click to collapse
Try here: CDMA Herman
same issue on GSM phone
Hi I have the same problem on a GSM phone.
I get the updating bar on my phone- it stays stuck at 0%.
then a communications error
Thanks in Advance
What is the problem with the RUU update?
I have searched for a solution to the RUU update/upgrade problem; none so far. Apparently, it is a major issue. I am interested in upgrading my Windows CE on my Xperia 6.1 to 6.5. I must have tried over a dozen times. The update process stops at 0% and Error [262] is reported. What can we do to resolve this? Is it compatibility or scalability issue? is it a problem with the software? The fact that it is working for some . . . and not for others is a source of concern about the stability of the software and this has potential implications; or it may well have to do with the hardware limitations of the PDA. Any ideas of a workaround?
You might try the Experia forum. You also might want to try Experia Roms.
I used to experience this issue as well. I simply go into communications and hit the USB to PC connection. Then remove the advanced functionality check. This has resolved many of the communication errors when playing with ROMS. This has been true with both GSM and CDMA devices.
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Dunno if i can link to another forum. If not, appolgize and Admins remove the link than please.
For the 262 error, look here:
http://www.4winmobile.com/forums/windows-mobile-faq/13329-ruu-errors.html
player911 said:
I can confirm the issue. I have a 1st day release Fuze and flashed HardSPL no problem and have been making my roms ever since. But my cousin just got his new AT&T Fuze through his company and it refuses to HardSPL.
I went through several versions of the HardSPL and tried installing new drivers for the phone while in bootmode... all with no luck.
When connected through Activesync or Mobile Center, running the HardSPL brings up a confirmation windows on the phone, allowing reboots the device. It gets stuck at the black screen and times out. I've tried manually putting the phone in bootmode and trying it, but never gets past 0%.
I wonder if newer model TouchPro's are coming out with a revised bootloader?
Click to expand...
Click to collapse
Yes they are coming with a new bootloader. I just got my phone replaced from ATT and the new one came with 1.95 version while originals were 1.90. There is no HARD-SPL out for 1.95.
The way to do it now is to flash an old original AT&T rom with the 1.90 bootloader (since it's original, it won't require HardSPL). Then go ahead and everything should work as described in this forum/wiki.
Interseting. Sounds like a winner. Next time he comes around I'll try this.
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
smicale said:
Any idea where I can get a AT&T older rom that has the 1.90 HardSLP on it? I am having the same issue with the Error 262 update error.
Thanks
Click to expand...
Click to collapse
You should probably go to your ATT store and tell them you'd like to get the official Hard SPL update.
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
smicale said:
I am really struggling with this. Do I have to the FLASH HardSPL or can I just go straight to the flashing my preferred ROM. I can not get get the FLASH HardSPL to work because of this Error 262. Please someone tell me where I am going wrong with this!!!! I am bout to pull my last hair out!
Click to expand...
Click to collapse
If u want to use not the official rom made for ur provider and phone, hardspl is the only way. Any custom rom needs hardspl. Otherwise ur phone will not accept the rom.
But look here http://forum.xda-developers.com/showthread.php?t=410150
and flash the stock 1.90 SPL first, then u are ready for hardspl.
Description how to do stock spl is in this thread. Its normally meant for going back to stock for repair, but it should also solve ur issue.
NOT SHURE BECAUSE IN THE CDMA SECTION, IS UR PHONE CDMA OR GSM. MY SOLUTIUON IS FOR GSM !!!!!!
U SHOULD CHANGE THE POSTING SECTION IF ITS GSM !!!!!
Try doing the HardSPL in a Windows XP machine (needs .NET Framework 2.0 and ActiveSync). Goodluck.
i had the same problem as you and i maybe have a solution for you
go to your usb settings and look if you have a check box saying something about advanced networking. if it is indeed checked uncheck it and your problem will be gone hopefully
i did it on my telus touch pro and i am now able to upgrade my phone to winmo 6.5
So, I have a 8125 T-mobile MDA Wizard. It is unlocked. It is currently running CR96 TouchHD v6.5.0.3.3 RC5. I have tried flashing it with TNT.19199 version 2 (Fixed Version) OS 11.0.1.1 and WM 6.1 20273 HORNET 5.1A. However, when trying to flash my device with either of these roms, I recieve a message from the updater saying that itwon't work and that i need to use a new updater(?!??!) I am very confused. Any help is greatly appreciated. I have also flashed it with the Wizard Love rom before each flash. I am also having issues with my wifi. It will turn on, and detect my neighbors WEP enabled access points, however it will not detect mine even though I am 4 feet away from it. I have gone through the proxy settings, and still no luck. I read in another post about a corrupted wifi eeprom? is that a possibility? once again, any help would be greatly appreciated
*edit: also what is the deal with all of the different radio (roms?) software upgrades? is there really any point in messing with that?
*edit: fixed wifi issue.
If you’re getting a good signal there is no point in messing with the radio.
ok, then what about the update issue? I mean when I try and reflash it, it says that I need a new updater. Will using a shelltool fix this for me even though my device is CID unlocked?
Give this “Update Utility” a try.
nope, didn't work. gave me error 300, same thing, please use a newer update utility
And another one "Update Utility".