As a new owner of a Verizon xv6800, I found some slight annoyances with the tutorials/guides posted so far. Therefore, I decided to write my own guide with the quickest and simplest way to upgrade directly from Stock firmware to the newest ROM and Radio. Despite my attitude towards past guides, I thank everyone who has posted a guide so far, as without those, I would not have been able to flash my phone or write my own guide.
Please let me know of anything that might need changed.
Thanks.
Tutorial is at http://ppc.stoleyour.net/xv6800/
Pretty cool guide - it should help real newcomers...thx for the post!
Can't dial "+1 (###) ###-####"
I was able to follow all the steps and flash succesfully. However, I am having trouble dialing phone numbers that include the "+" in front of the country code. This worked fine on the stock ROM, but when I flash I can not dial any of the number unless I remove the "+" from in front. This then messes up outlook and I can not sync. I think its a dialer issue, but not sure. Everything works (voice calls, data, gps) but I can not dial from the contacts that sync. Did I mess something up, or do I need a different dialer, or something else?
I started Friday night and I am still working on it (Monday)...
Verizon XV6800
Olipro 2.40
3.42.30
3.2.0 (customized in the kitchen)
Try this,
HKLM/Software/OEM/PhoneSetting/PlusCodeDialing
PlusCodeEnable change to 1
connection issue
I am getting a connection error even after disabling my usb in active sync.
It gets to 8% i get a connection fails error, and my phone reboots?
3.39 radio
3.2.1 dcd
I have an issue after following your tutorial.
I followed it to the T.
However, after running the *228 command, it shows the yellow text that it is programming. After about 60 seconds it shows "programming unsuccessful".
If I try to call it again, every consecutive try (without doing a reboot) does not show the programming text. However, if I reboot the device, it does show programming but fails again.
I have also attempted to reinstall the Verizon CAB and it does not affect my issue.
Any suggestions?
grstarrett said:
I am getting a connection error even after disabling my usb in active sync.
It gets to 8% i get a connection fails error, and my phone reboots?
3.39 radio
3.2.1 dcd
Click to expand...
Click to collapse
Interesting problem. Just for the sake of ruling it out, have you tried another USB cable/port?
If you have no luck with that, you might be able to flash using a MicroSD card. I had no luck using mine (4GB PQI MicroSDHC card), as it kept giving me some error trying to flash with it.
Some info on the MicroSD method: http://forum.xda-developers.com/showthread.php?t=378506
Hope that helps some. If not, let me know.
grstarrett said:
I am getting a connection error even after disabling my usb in active sync.
It gets to 8% i get a connection fails error, and my phone reboots?
3.39 radio
3.2.1 dcd
Click to expand...
Click to collapse
Apparently the new firmware likes to break at 8% doing update over USB and will tell you that it's incompatible or whatever. The only way to flash the radio in this case is by using the MicroSD method. Make sure you use a non-MicroSDHC card, format it properly, and copy the image onto the device as TITAIMG.NBH
ih8aol said:
Try this,
HKLM/Software/OEM/PhoneSetting/PlusCodeDialing
PlusCodeEnable change to 1
Click to expand...
Click to collapse
Thank you for the suggestion. However, I had already decided to revert to the stock ROM until I feel confident I can resolve the issue. I took a look at the stock ROM registry, and interestingly the value is 0. I will make note of the other keys and look at them next time I try the new ROM.
Thanks again, it's a great feeling to get a response that may help.
very nice. clean and simple.
Related
Appologize for posting the thread twice... I wasn't sure if this goes to the Hermes or the Herald forum...
Hello All,
I recently got an ATT 8525 and I'm trying to use it with my T-Mobile (US) SIM. I was able to successfully unlock the SIM and CID with an util/rom I found on this site (I think the post was from Pof). And I also re-flashed the phone with the latest ROM available.
But after about 5-10mins of usage the signal dies and when I reboot it says No GSM. Looks like the Radio ROM gets corrupted. I tried just re-flashing the Radio ROM and that doesn't help either. It works for short while and again the signal dies.
And also, I'm unable to install any of the generic ROMs (Fantastic Mobiz, PVET 40005) Although I'm connected to Active Sync when I run the Step 1 (ROMUpdateUtility_NV_G3.exe), I get a ERROR [222] : DEVICE NOT RESPONDING. And when I run the step 2 directly (update_rom.bat) I get an cannot update itsutils.dll maybe in use error.
As you can tell I've been messing with phone a lot for a couple of days with no luck and my frustration level is kinda high
As of now here’s where I stand. I re-flashed the phone (Image: 3.62, Radio 1.50) and it’s on the “Tap the screen to set up your windows based mobile device” screen. I plan on leaving it on this screen until I can a good solution.
I would like to get rid of the ATT ROM and install one of those hybrid generic ROM that is not Carrier specific. Any help will be much appreciated. Share your ideas, I’m very experimental
Phone Details…
ATT 8525
HERM100
IPL: 1.04
SPL: 1.40.0 lipro
ok ur going all over the map here.. did u hardspl first? also pvet 40005 isnt a hermes rom.. um try hardspl first THEN flash to a new rom maybe once you successfully do that then try a new 3.62 rom.. i run austinsync buts its naked..just like i like my women. ha. but if ur looking for a full blown try fun_key's rom or blinkys.. these arent carrier dependent
hey man jakeypoo, Thanks for your reply. I kinda figured that I was all over the map.
Okay first appologize my ignorance. What is a HardSPL? I did a search on this forum and I found Hard-SPL-V7.zip. Is this a good version to use? Also when I run the exe, All options are grayed out except for "Force Using SSPL" and "Is it Hard-SPL". What do I select.
Thanks!
Hardspl v7 is the latest version out there, its the one for you to use so that you're safe from future mishaps.
I also have an 8525 on T-mobile... so no worries.
Hope this helps.
http://wiki.xda-developers.com/index.php?pagename=Hermes_HardSPL
still problems (no gsm)
Thanks whistler4ever. That link was really a great help.
Here's what I did...
1. Installed the Hard SPL version 6
2. Installed the latest ATT ROM (ver 3.62 radio: 1.54) I had to do this because the radio on the phone was corrupt (says "no GSM" on the start screen) and couldn't install just the radio rom. kept giving connection errors.
3. Installed Schap's WM6 Pro 3.57 hoping this would get ride of the ATT ROM and my intial problem (no GSM) will go away.
Everything was fine for like 15 mins, then my phone just froze. I reboot the phone and sure enough the radio ROM was gone (no gsm). ;(
Running out of ideas.
1. Could this problem be because I'm using a TMobile SIM on a ATT's radio ROM?
2. Is the radio ROM specific to the phone type and provider(ATT, TMO..)? Is there a generic WM 6 radio rom? If yes, where can I find the latest version?
3. Any bright ideas?
Thanks again!
Current phone details...
ATT 8525
HERM100
IPL: 1.04
SPL: 2.10
ROM 3.62
Radio: no gsm
I was able to flash just the radio ROM - version 1.51. But again after a few hours the Radio got currupted. I also tried to follow the instruction ( http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5 ) to use the mtty.exe utility, but I don't get a USB prompt. I get Cmd prompt and if I still enter the password, it says invalid password. please help!!!
And how do I do the USB monitor capture? I could post more details that way. I'm using my girl friend's old razr now and it's painful!
I have used my t-mobile sim on AT&T rom's and other roms with no problem. I would try going back to a factory rom and then changing back to a cooked rom just to confirm its all a clean install. also, try downgrading your radio to a 1.47 or 1.48 (those have been proved pretty reliable across many cell providers).
Thanks Whistler. I'm going to start with the 1.48 version and if that doesn't work I'll try the 1.47 version. Not giving up on this.
I found 1.47 to work very well with t-mobile even when traveling...
Thanks Galaxys. I just installed the 1.47 radio. I have fully signal and the 'E', but I can't receive or make calls.
It almost looks like my TMO SIM is not compatible with the 8525. It always works for the first few minutes after an install and then stops working.
I'm very certain the phone is in good condition.
Should I try an older radio version.. like a 1.24 or something ?
Can I install just the tmobile radio rom?
I'm also going to install TNT 2.0 pro so I have the exact same set up as you and see if that makes a difference.
no luck!!!
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
try the way i posted in this thread http://forum.xda-developers.com/showthread.php?t=337125
ajjus said:
wow... after all this time and effort still no luck. There's got to be something very basic that I'm not doing right. Senior members any help???
I have spent a lot of time reading the wiki pages and dead hermes thread. Tried out a lot of suggestions listed.
Click to expand...
Click to collapse
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Try to flash the entire UK T-Mobile ROM, then remove the internet settings and install the correct CAB for T-Mobile.
UK ROM here: http://forum.xda-developers.com/showthread.php?t=337163
PROVIDER SETTINGS CAB: http://forum.xda-developers.com/showthread.php?t=311446
a-h-t1, Junner2003 and galaxys - I'll try all your suggestions.
a-h-t1 - The first 2 steps went through fine. While I install the radio ROM as part of step 3, the installation doesn't go past 0%
I'm going try Junner2003 idea now. I'll keep everyone posted on my progress.
install stops at 11%
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
galaxys said:
Sounds like your doing everything right, because your flashed rom, radio, and Edge network are all functional. Since only the GSM calls don't work, I would go back to Tmobile and get a a new Sim card installed (they should do this for nothing & test it while at the store).
Also, if U got this device on ebay your IMEI could be blocked. see this thread:
http://forum.xda-developers.com/showthread.php?t=322587
Click to expand...
Click to collapse
Hi Galaxys,
I don't think the IMEI is blocked. Or maybe it is, how do I find out? I don't have any of the symptons listed on the link you sent (don't hear the beeps or anything).
I originally had a T-Mobile wing. The LCD screen cracked (don't know how). And ofcourse TMo won't replace it.
http://forum.xda-developers.com/showthread.php?t=335346
I got 8525 from my company. It's almost new. Only used for a day on an AT&T SIM. This phone is free, and so I really don't have much to lose... so all out experimenting
Tried insalling from the micro card, even that stops while installing GSM. pissed!!! Why would the darn Radio not update???
this may sound stupid but if all else fails, why not...
my mda use to have signal then it would just disappear as well after 15 min or less..
turns out the sim card wasnt pressed in properly.. so i just put a piece of paper on top of the sim card to make it thicker and get the battery to press it down harder. and it solved all my problems...
just a suggestion..good luck
ajjus said:
Hi Junner2003,
I was trying to istall the UK Tmo ROM you suggested and it stops always at 11%. I've had this problem with other ROMs as well (12%) but after a few tries the installatons goes past it, but real slow. Any ideas?
Thanks for sending me the links... very helpful!
Click to expand...
Click to collapse
See this post here for a possible reason (and technical explanation/theory) for your device stalling during radio update. The fix suggestions at the bottom of the page may help you - in particular :
Try cooling the device down a bit before flashing as the PIC chip (where your radio ROM is held) may flash more reliably/easier when cool. Don't ask why - that's from it's datasheet ;-)
The paper on the SIM card is a good idea too to rule out dodgy SIM connection - Great idea r0mmel
Can anyone share their experience upgrading their Bell HTC6800 ROM (including radio, unlocking SPL, and upgrading PRL) with DCD 3.0.1? I have never done it before but curious to hear if anyone has had success or failure.
I noticed that DCD released a Bell ROM in his 2.3.2 kitchen but not in his 3.0.0 kitchen. Does anyone know how to port the correct Bell settings into the 3.0.0 release?
My main reason for upgrading is of course better performance but more importantly I am curious about aGPS and how I can use it instead of my Bluetooth GPS receiver. If anyone can share that would be much appreciated.
http://rapidshare.com/files/99219142/DCD_3.0.1_Bell.exe
Check the last page of this thread
http://forum.xda-developers.com/showthread.php?t=363693
Thanks origins81. I noticed now that DCD added the Bell ROM to his 3.0.1. So can you share you experience with this ROM upgrade? Did you have any problems (I assume you've done this before)? Can you share your experience if you are a Bell HTC 6800 user?
1. If you have not already done so, run the 2.40-olipro unlocker. Your device will again be left in tri-color screen.
2. Flash the official sprint 3.35 update.
3. When the device boots for the first time, do not pass screen calibration. Flash a 3.x.x ROM. (that being the custom rom of your choice)
Think I only used the official Bell rom for about a day before i got sick and tired of it and flashed to one of DCD's clean roms, never looked back since then...
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Thanks guys. You have instilled more confidence in me now. I am just going to make sure I have the original stock ROM from ustar as well as the Titan re-locker just in case (I want a backout plan). I will wait a little longer until everyone irons out the kinks of this new 3.35 radio and I will give the latest DCD ROM a try. Thanks again!
I've used the SPRINT update and it works fine. I've added the quick GPS program that comes with the DCD version and I am going to change the startup logos from Sprint to Bell...(As soon as I figure out how). I didn't need to reprogram anything!!
I just got my phone today, gonna give this a shot...
oh man... i ran the olipro 2.4 file and it took me to the tri color mode and then tried to flash it with the latest sprint update. it went up to 4-5% and then it showed an error of Update Utility. i tried to go bak to the Bell update and it did the samething but this time after 1%. can someone please help me out here? I'm with bell.
ok now i'm stuck at the bell screen and at the bottom it says "No Radio" cuz i tried flashing the dcd file.
Well, to begin with, here are the steps I took to accomplish what I have.
1. Flash Olipro 2.40
2. Flash Radio to 3.35 (For the newest version of DCD's rom)
3. Flash the ROM to DCD's rom.
Now, the first time I did this, I got stuck at the tri-color screen, such a pain. I then tried flashing the rom again, and it rebooted continuously and I had no idea why. This was because I didn't flash to the newest radio. So I did that, and it worked, so try those steps, and good luck.
On problem that I did notice is that my phone always has the roaming triangle on?? Hopefully it's not costing me roaming charges... I was going to try and use the DCD 3.0.1 rom but don't want to chance it. I'm going to try playing with it some more an see what happens.
I'm running DCD 3.0.1 on my Bell 6800 and it's working great so far (day 2)
Follow Origins81's install points above, and remain calm if it takes a try or two to get past the 2.40-olipro unlocker 3-color screen step.
I'm having some issues ActiveSync'ing to both work and home PCs, but I don't think it's related to this ROM.
GPS works great with Google Maps
The alarm clock bug is fixed (e.g. not working when plugged in)
Got it working and everyhthing is great except is doesnt play video in the media player...Working on it.
Well for some reason I can't seem to activate my phone. I hit Talk then I enter ##911224#. It tries to connect for 15 secs then hangs up.
I _thought_ I did everything properly.
1) Ran Olipro2.40 (actually it was the unlock from http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/) it looks like it's got Olipro2.40 in it.
2) ran official upgrade from sprint (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship.exe)
3) Extracted DCD_3.0.1_Bell.exe and ran the RUU.
hope I didn't perma-brick it.
M
Ok fixed it. Browsed around the and found out in a Howard forum that you have to type ##111111# (doh!) before. Ok my heart can start beating again! Posted for posterity. The code that I used must have been for a different area. This phone is from the GTA.
can you give me a link to those howard forum posts because i ran into a problem ... after a last flash my phone works but its not activated... I tryied ##111111# but i get a code check error... ##911224# doesnt do anything... ##778# works but 000000 code doesnt so i cant get in... HELP
Roaming After Update
After suffering with the pesky Bluetooth issues with my HTC, I thought I'd do some searching on the Internet to see if others had the same issues. Lo and behold, it looks like a real bug with the HTC. After reading some forums, it looked like the latest Sprint release would cure the problem. I downloaded an unlock program ("Hard-SPL-MFG") and the Spring update (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship)
and proceeded to update my HTC.
After a few unsuccessful attempts (stuck at the three color bars a couple of times, restarting a few times on it's own) I managed to get the unlock code and Sprint update installed.
The problem I have now is that it appears that I am now roaming even though I'm in my calling area (I'm with Bell Canada)!
Help! What should I do??
Check the bottom link out, had similar issues when I first flashed. If you have any further questions let me know
http://forum.xda-developers.com/showthread.php?t=363693&highlight=FOR+BELL
i follow the step, but when the phone restart, i stuck a the bell screen...
i'm unable to connect with the usb.
Can you able to help me ? to complete the installation or trying to go back OEM
- i do the first step; see the red, green, blue screen (http://forum.ppcgeeks.com/showthread.php?t=9093)
- flash the rom
- now stuck......
thx for your precious help
TwistedWaffle said:
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Click to expand...
Click to collapse
Hi TwistedWaffle, Are you from the montreal region? I am looking for somebody who would do this stuff for me... Can you help?
My phone came across some issues. Don't ask how. I have a few issues and heard this is place to go. Here goes.
I tried to turn my phone on.
It vibrated, the green light turns on, but no display.
So I turned it on to the Bootloader screen (it's the only display I have). It reads:
"TITA100 MFG
SPL-2.40.Olipro
CRLD-9"
I connect to the computer, and I hear the chime to confirm its connection.
However, I open Mobile Device Center and it doesn't show that a phone is connected. I go to to Device Manager, and I see that there is a "Microsoft USB Device" connected, which is my phone.
So in all, when I try to flash a new ROM, it tells me there's a connection error. However, it knows my phone is there because the phone's screen changes. HOWEVER, when the flash is operating, it tells me what ROM its flashing to. It does not tell me the image I have though, which leads me to suspect I don't have a ROM at all on my phone.
I'm dead confused as to what to do. Everyone has an actual OS to use and to connect to Mobile Center (activesync). So...help me out if you can?
I don't want my little baby to die.
...come on...breath Mogul...it'll be ok.
You have unlocked your phone and have the 2.40 bootloader installed which is suitable for the 3.35.xx and later based ROM builds. You must also match your chosen ROM with a suitable radio.
Activesync will only make a connection when you are booted into Windows Mobile. For flashing, that connection is only necessary to unlock/lock your phone and change the bootloader.
You are fine, but are not telling us what you are trying to flash to or what information you are following to flash. If you read the sticked threads on the front of the forum and check out and follow the instructions posted in the Titan Wiki for upgrading to the latest GPS/EDVO Rev A ROMs, you should find all the links and information you need to successfully upgrade your phone.
Thank you very much.
I thought I was stuck.
I think I'm going to upgrade to the latest ROM and try to get it running. This leads me to a new question:
Is there any special step I need to take when wanting to Flash using the SD Card? The ROM, let's say 3.35 Alltel. I put it in the card and it says "Loading", then it shows the number "00068002" in red up top, and then the blue words "No Image File!" appears.
Alvaster said:
TIs there any special step I need to take when wanting to Flash using the SD Card? The ROM, let's say 3.35 Alltel. I put it in the card and it says "Loading", then it shows the number "00068002" in red up top, and then the blue words "No Image File!" appears.
Click to expand...
Click to collapse
You are missing out a few steps in telling us what you have done. Tell us exactly what you are doing and with what type of card.
Alrighty.
I have a 1 Gig card, FAT32 1024.
I'm trying to get the "Alltel 3.35.671.9 ROM".
I read that I am to flash that ROM first, but like I said, the progress bar shows up on my phone when flashing with the .exe program (gray background, progress bar up top), and then it gives me an error message and I have to reset my phone and go through the tedious "recovery" process.
When I try to use the SD Card to install the Alltel image 3.35.671.9, it says Loading, and then No Image!, and it takes be back to the BL screen.
Is that enough?
Thank alot.
As you have apparently have a suitable SDcard, you don't need to bother with the Alltel ROM. You can directly flash a suitable discrete radio ROM (links in the Wiki to 3.37.20 & 3.39.10). Less hassle that way and the best method for future radio changes without affecting your data or OS ROM. With the CDMA Radio upgraded you can then repeat with the SDCard routine to flash to one of the later third party ROM or kitchen build of your choice. After that, all should be fine to boot into the new OS.
Remember that the ROM file copied to the root of the SDcard must be renamed TITAIMG.nbh.
Damn it all.
I put the card in with the Radio in it, named "TITAIMG.nbh", and it only reads "loading" then "No image file!"
I tried both Radios, and my card is fine.
Still no luck.
Geez...what a disappointment. Thanks for your help though. I feel safer knowing there's hope for the thing.
Did you format the card into FAT32 from your PC?
Oh well, I guess again resort to using the latest Alltell or Sprint ROM via the USB to upgrade your radio. Rather than using their installation routine you can again extract the ROM image but now manually initiate the ROM Update Utility as described in the Wiki.
Thanks again for the tips and info.
Sadly, flashing by SD always gives me a "No Image File!" message, and flashing by USB always gived me a 262 Update Error message, no matter how many times/ports/resets I do.
I guess I'm stuck then.
Hello,
I hear nothing but great things about custom ROMS, especially DCD and would like to try one. I have spent the last few weeks reading all the threads located here on XDA-Developers and on PPCGeeks regarding upgrading an OEM Verizon XV6800 to a custom ROM.
Below are the instructions I have come up with. I would appreciate it if this wonderful community could provide any suggestions or corrections to my steps. Based on your responses I will create a finalized guide for other users to follow.
I have received very mixed results regarding the overall procedure. Some say you must first flash the Sprint ROM and then flash DCD (To upgrade the radio). Others say you can just flash radio 3.39 and then flash DCD 3.1.6. My below steps are going on the assumption you can just flash the radio 3.39 and then flash DCD 3.1.6.
Phone has
Software Version: 2.09.605.8 (I believe this is the ROM version)
Firmware Version: 1.30.60 (I believe this is the radio version)
I have doccumented my
NAM, SCM, ESN (Hex & Decimal) and MSID.
1. Backup everything
2. Connect the phone to the computer using USB cable and ensure it can establish an active sync connection.
3. While the phone is connected to the computer and running Windows Mobile 6.0 run titan_SPL_2.40-olipro.exe to unlock the phone.
4. Reboot the phone and put it in to bootloader mode (Hold down Power button, camera button and press the soft reset button with the stylus until the multi color bootloader screen appears).
5. While in bootloader mode flash the radio to 3.39
6. While in bootloader mode flash the DCD 3.1.6 ROM
7. After reboot install the Verizon carrier cab. Call verizon and let them know you have hard reset your phone so it can be re-authorized with their network.
everything looks good, what i would do though is flash the 3.39 sprint rom to get the radio. and you may not have to call verizon i just got a replacement phone and flashed up did the *22899 and everything worked with out having to call and get a a key.
s10onn2o said:
everything looks good, what i would do though is flash the 3.39 sprint rom to get the radio. and you may not have to call verizon i just got a replacement phone and flashed up did the *22899 and everything worked with out having to call and get a a key.
Click to expand...
Click to collapse
another suggestion i've seen somewhere else is to turn the phone into flight mode prior to flashing... not sure if it works but would be interested to know
also: DO NOT FORGET to soft reset just beforethe customizations run (when you are finished flashing and the phone reboots itself for the first time..)... you do NOT want the sprint customizations to run, on your Verizon device.
nickles96 said:
also: DO NOT FORGET to soft reset just beforethe customizations run (when you are finished flashing and the phone reboots itself for the first time..)... you do NOT want the sprint customizations to run, on your Verizon device.
Click to expand...
Click to collapse
if it's your first time you won't know when the sprint customizations are running. so just don't hit the screen or anything until AFTER you flash a DCD rom
the 0ne said:
I have spent the last few weeks reading all the threads located here on XDA-Developers and on PPCGeeks regarding upgrading an OEM Verizon XV6800 to a custom ROM.
Click to expand...
Click to collapse
I was in the exact same spot just a few weeks ago, flashing my XV6800 for the first time. I researched and prepared like you have and I think you're ready to pull the trigger.
My only advice is to use the SD method to flash the radio and OS ROMs. I wasn't able o connect via USB after upgrading the radio and the microSD method was incredibly easy and far faster than USB seemed.
Dialing *228 was all I needed after the process was complete, no new A-Key needed or manual entry of provisioning data.
Just remember, when in the process of flashing your phone, keep calm & carry on.
VX6800 upgrade procedures please
I too have read all the post on this and PPCGEEKS and have issues within myself. I start out with a high confidence level and after you get through a page or two of; yes, but do this instead ..... you are left with nothing but total confusion and contradictions. My confidence level is then well down the ladder.
I (we) would all like to hear from a VERIZON VX6800 owner (no sprinters please, sorry) who has actually done this with step by step instructions. Please don't assume we know anything, many like myself are knowledgeable in technical fields but not with PPC's.
This is my most serious concern. I ONLY have access to machines running Vista. I have heard that something, don't know what, will stop at 11% some people say not. What might stop and why? Ive also been told that there are new drivers for 'mobile device center' that fix this problem but no driver dates or version No's are posted anywhere. Any advice here would be helpfully also.
I know several folks who are also waiting for me (the guinea pig) to do this and they will follow.
Thanks for the time all have put into this effort.
All of the instructions and options for flashing are up-to-date in the Wiki.
I own and operate an xv6800, I used the methods listed in every sticky to flash my first time, never had a problem.
I have always used DCD's ROMS and used whatever he had posted in whatever thread for every ROM/kitchen. The man is thorough in putting the necessities in his threads.
Now I just flash whenever, no problems. I run 32 bit vista and xp on my machines and neither gives a headache.
The wiki is your guide to a successful upgrade. Study it.
Nonetheless, for those wanting VZW-specific instructions, here's how I upgraded my XV6800 to radio 3.39.10 and dcd's 3.1.2 a couple weeks ago.
I take no responsibility for anything you do to your device.
Code:
I. Upgrade bootloader
A. Establish an ActiveSync connection via USB
B. Execute Hard-SPL-MFG.exe to upgrade the bootloader to 2.40
[url]ftp://up.ppcgeeks.com/Titan/Users/ImCoKeMaN/roms/Hard-SPL-MFG.exe[/url]
Follow the steps in the command window closely - they are very clear
II. Format a microSD card for installing radio and OS ROMs
A. Using a card reader attached to your computer, format a microSD card into FAT32 with an allocation unit/cluster size of 1024
1. Open a command prompt and type
format ?: /FS:FAT32 /A:1024
where ? is the drive letter assigned to the microSD
III. Use microSD to install Radio ROM
A. Download radio 3.39.10
[url]http://rapidshare.com/files/113794877/radio339.rar[/url]
B. Un-rar
C. Copy RUU_signed.nbh to your microSD card
D. Rename RUU_signed.nbh to TITAIMG.nbh
E. Insert microSD card into phone
F. Force into bootloader by pressing POWER+CAMERA+RESET
G. Bootloader will load and begin loading the ROM on the microSD
F. When radio upgrade is complete, reset phone and force into bootloader
IV. Use microSD to install OS ROM
A. Download the OS ROM (e.g. dcd_titan_3.1.2)
B. OS ROM will be .exe file. Use WinRAR to extract files, one of which will have an .nbh extension
C. Copy *.nbh (e.g. dcd_titan_3.1.2.nbh) to your microSD card
D. Rename *.nbh to TITAIMG.nbh
E. Insert microSD card into phone
F. If not in bootloader, force into bootloader by pressing POWER+CAMERA+RESET
G. Bootloader will load and begin loading the ROM on the microSD
F. When OS upgrade is complete reset phone, eject the card, reset the phone
You will more than likely need your USB-headphone dongle/adapter that came with the phone.
After I upgraded my phone, resetting the phone caused the bootloader to appear instead of
loading the OS. For whatever reason, with the 11-pin USB dongle this doesn't happen
and the OS ROM boots without a problem.
V. Follow on screen instructions and allow customizations to run. Phone will reset when complete.
VI. Install Verizon carrier cab, reset when complete.
[url]http://www.lifesnotsogood.com/dcd1182/titan/carriers/dcd%20Titan%20Carrier%20-%20Verizon.cab[/url]
VI. Dial *228, reset when complete
VII. From your phone, browse to [url]http://ota.wsync.com/[/url] to download, install the XV6800 Over The Air sync client
After I upgraded the radio I wasn't able to load the stock OS and was unable to establish an ActiveSync connection via USB, thus was unable to use the RUU method. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.
arnoldbabar said:
You will more than likely need your USB-headphone dongle/adapter that came with the phone.
After I upgraded my phone, resetting the phone caused the bootloader to appear instead of
loading the OS. For whatever reason, with the 11-pin USB dongle this doesn't happen
and the OS ROM boots without a problem.
Click to expand...
Click to collapse
Can you explain this more? Are you saying everytime i reboot my phone i will need the USB/Headphone adapter plugged in? Or just the first boot?
Also, I dont have a SD reader. Can i just copy the files to my SD card with the SD in the phone and connected via USB?
Thanks,
Mitchell
Are you saying everytime i reboot my phone i will need the USB/Headphone adapter plugged in? Or just the first boot?
Click to expand...
Click to collapse
For me, only about 1 in 3 reboots do NOT require the USB dongle. I have no idea why that is, I think it's an issue with the bootloader, but there are some threads on this board with more technical info. (I work in IT and carry a whole mess of cables in my bag, so it wasn't a huge concern of mine to tote the USB-headphone adapter around.)
Also, I dont have a SD reader. Can i just copy the files to my SD card with the SD in the phone and connected via USB?
Click to expand...
Click to collapse
Nope. You can read/write to the card but I don't think you can change the file system of the card while it's in the phone. Card readers are cheap, less than $20, and very handy to have.
After I upgraded the radio I wasn't able to load the stock OS and unable to establish an ActiveSync connection via USB. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.
Also, when getting the required info before i start i dont see a key for security when i do a ##778. Is this ok/normal for verizon?
Thanks again!
After I upgraded the radio I wasn't able to load the stock OS and was unable to establish an ActiveSync connection via USB, thus was unable to use the RUU method. Using a card reader and microSD method to flash the new OS ROM saved my ass. I won't flash any other way now.[/QUOTE]
After the entire process was complete you are able to sync with the PC? Just not prior to doing the ROM update? Syncing is essential to me for backups etc.
Thanks for all the advice guys!!
wow, so i just remember i had a SD reader on my linux server. I went down and loaded up my VM of XP. Started to format my SD card and it blue screened and now I cant get my SD card to reconize in my computer or phone. I guess that a worthless piece of plastic now.. Ill try the USB method.
mitchell2345 said:
Also, when getting the required info before i start i dont see a key for security when i do a ##778. Is this ok/normal for verizon?
Click to expand...
Click to collapse
That was the same for me when I checked my EPST before upgrading. That's a good thing: you don't have an A-Key (security) now so you won't need one after flashing.
Rich W said:
After the entire process was complete you are able to sync with the PC? Just not prior to doing the ROM update?
Click to expand...
Click to collapse
Correct. However, now when I sync I have to use the USB/Headphone dongle. I can also sync via Bluetooth.
I just want to say thank you to everyone. I was able to get DCD 3.1.6 running by flashing the Sprint ROM and then flashing DCD 3.1.6. The only problem I'm having is getting Radio 3.39 to load. It will get to 8% and then the phone reboots.
If anyone is near newport news VA and wouldnt mind helping me out with upgrading my 6800 let me know. Ill provide the beer
So, I have a 8125 T-mobile MDA Wizard. It is unlocked. It is currently running CR96 TouchHD v6.5.0.3.3 RC5. I have tried flashing it with TNT.19199 version 2 (Fixed Version) OS 11.0.1.1 and WM 6.1 20273 HORNET 5.1A. However, when trying to flash my device with either of these roms, I recieve a message from the updater saying that itwon't work and that i need to use a new updater(?!??!) I am very confused. Any help is greatly appreciated. I have also flashed it with the Wizard Love rom before each flash. I am also having issues with my wifi. It will turn on, and detect my neighbors WEP enabled access points, however it will not detect mine even though I am 4 feet away from it. I have gone through the proxy settings, and still no luck. I read in another post about a corrupted wifi eeprom? is that a possibility? once again, any help would be greatly appreciated
*edit: also what is the deal with all of the different radio (roms?) software upgrades? is there really any point in messing with that?
*edit: fixed wifi issue.
If you’re getting a good signal there is no point in messing with the radio.
ok, then what about the update issue? I mean when I try and reflash it, it says that I need a new updater. Will using a shelltool fix this for me even though my device is CID unlocked?
Give this “Update Utility” a try.
nope, didn't work. gave me error 300, same thing, please use a newer update utility
And another one "Update Utility".