i am trying to check my hermes CID
but mtty display "USB port can not open"
so how to solve it ?
please and THX
Disable USB connectivity in ActiveSync (right click on the icon on the task)
Simple.
simple said:
Disable USB connectivity in ActiveSync (right click on the icon on the task)
Simple.
Click to expand...
Click to collapse
i did it but problem can not be solved
no active sync on vista how to 'close usb port' on win vista?
Use Windows Mobile Device Center to do so:
Start Orb -> Control Panel -> Windows Mobile Device Center -> uncheck "Enable USB connections"
killerb255 said:
Use Windows Mobile Device Center to do so:
Start Orb -> Control Panel -> Windows Mobile Device Center -> uncheck "Enable USB connections"
Click to expand...
Click to collapse
I've done such work but the mtty still appear "USB port can't open"
Have you Hard SPLed your phone?
If not, do so with ver 7. I remember reading that you need to Hard SPL installed to use MTTY...
Cheers...
some versions of mtty are a bit funny about usb comms. I use version 1.42 and it goes fine.
MTTY v 001 has USB option
MTTY 1.42 does not have USB option?/
please help!!
chanho2010 said:
i am trying to check my hermes CID
but mtty display "USB port can not open"
so how to solve it ?
please and THX
Click to expand...
Click to collapse
You are getting this error because you are trying to acces the device which is powered on. Reset the device where you see the tricolor screen [Bootloader screen] http://wiki.xda-developers.com/index.php?pagename=Elf_Resets and then run mtty.exe.
try going to windows mobile >mobile device settings > and press the scroll under allow connections to the following . put the same port in wmd as in mtty. like(com 6 on both) hope this helps
mtty
end123 said:
MTTY v 001 has USB option
MTTY 1.42 does not have USB option?/
please help!!
Click to expand...
Click to collapse
install activesync if u don't have it and then uncheck "usb connection" in activesync.(right click on the icon on the task). u also have to end "rapimgr.exe" and "wscecomm.exe" in task manager. hope this helps
Related
In mtty.exe I can't select usb as the connection...
My bootloader says it is connected by USB....
Any suggestions?
Have you unchecked "Allow USB Connection" in the ActiveSync connection settings?
JR_de said:
Have you unchecked "Allow USB Connection" in the ActiveSync connection settings?
Click to expand...
Click to collapse
yes.... I sure did.
What is your Operating System? Vista or XP?
For Vista you need to install additional drivers.
have you pressed ok and power and reset at the same time to enter bl mode?
Also try closing the ActiveSync program on your desktop...goto task manager and kill wcescomm.exe process. After that, try opening the mtty program.
Maybe you have wrong versionof MTTY which happen to me before. Get the good MTTY in this package;
ftp://xda:[email protected]/Hermes/Cooked_ROMs/SPL-1.01MFG_Pack.zip
Problem was in USB connection in Win2K
Thanks guys, problem solved, my work laptop could not cope with the USB connection; now all problems are solved.
Thread can be closed!
My solution
Take the sd card, i was having the same problem and when i took the card it started to work...
It is the first time I flashing rom.
when I make my device into bootloader mode(tri-color screen)
the device will become no response and my pc cannot recognizes the device
but when I push the reset hole
the device can reboot and no problem
how to solve it?
I cannot do any unlock or flash procedure!
please help!
My device info.
Softbank X01HT(flashed to HK dopod rom before purchase)
IPL: 1.01
SPL:1.04
Rom version: 1.23.708.4
Rom date: 07/24/06
radio: 1.13.00.00
protool: 32.49.7018.00W
I have installed .NET Framework 2.0
go to activesync, > file > connection settings > and uncheck "allow usb connections" put your phone into bootloader and plug it into your pc... once your done flashing then go back and re-check "allow usb connections"
shogunmark said:
go to activesync, > file > connection settings > and uncheck "allow usb connections" put your phone into bootloader and plug it into your pc... once your done flashing then go back and re-check "allow usb connections"
Click to expand...
Click to collapse
thx for your reply
but the problem is
my pc cannot connect my device during boot mode
my pc said that new hardware found but it cannot be used normally...
is there need any driver?
Penguina said:
thx for your reply
but the problem is
my pc cannot connect my device during boot mode
my pc said that new hardware found but it cannot be used normally...
is there need any driver?
Click to expand...
Click to collapse
when you enter bootloader mode, does it first display Serial then, when you plug in the USB, does it display USB
Olipro said:
when you enter bootloader mode, does it first display Serial then, when you plug in the USB, does it display USB
Click to expand...
Click to collapse
thx for reply
it displays serial
but when I plug in USB cable
nothing change
PS. I have untick 'allow USB connection' in activesync before
Penguina said:
thx for reply
it displays serial
but when I plug in USB cable
nothing change
PS. I have untick 'allow USB connection' in activesync before
Click to expand...
Click to collapse
your bootloader is corrupt, flash Hard-SPL... you're lucky the damn thing boots.
Olipro said:
your bootloader is corrupt, flash Hard-SPL... you're lucky the damn thing boots.
Click to expand...
Click to collapse
o...but when I flash Hard SPL v6, when it turn to tri-color screen
it shows
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
then the device become no response
later my pc show error 260, miss connection
....
thx all!
I found the reason...
becoz I use activesync 4.1....
when I upgrade to 4.5
I can flash hard spl
when i want to open mtty.exe . i couldnt see usb port. program said that usb port couldnt open. ????
why :
do you know::
i only see active com3 but coudlnt see usb>
thanks
qrshad said:
when i want to open mtty.exe . i couldnt see usb port. program said that usb port couldnt open. ????
why :
do you know::
i only see active com3 but coudlnt see usb>
thanks
Click to expand...
Click to collapse
I get this sometimes. I didn't know if it was because I am running it under a virtual windows environemtn on a Mac. What I do to get mtty to recognize my port is this:
1. Start ActiveSync
2. In ActiveSync press "connect" or search for connected devices or something like this (since you are in BL mode, AS won't see the device, but it will poll all the ports, effectively making the USB port visible.)
3. While AS is searching the ports, launch mtty and choose selection box for port.
4. Voila' The USB port is usually visible.
If that doesn't work on the first try, a few more tries usually gets it working.
vista problem?
I suspect you are running Vista. You need to rollback to an older wm5 driver in order to "see" the port.
Regards
i was trying to upgrade the HTC offical ROM. but my hermes was bricked and stuck on the blue windows logo screen now. please help me
(it display NOGSM on the dopod logo screen also)
i have no any idea now and my hermes without the KITL mode
so what can i do .plz help me
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
5. You should see a white screen, hit enter and you should see a prompt like this: "USB>"
6. Type set 14 0 (do not copy and paste!!!) and hit enter
7. Soft reset with stylus
8. OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore!
9. if it doesn't unbrick, repeat all the steps but with the command set 16 0
I want to add something here that worked for me. Tried steps above but it didn't work. So what I did to get mine going again:
ciaoo kB
kb_lejardinier said:
hi,
try this :
http://wiki.xda-developers.com/index...pgradeProblems
or :
Problem 4: Device is stuck in bootloader mode (tri-color screen)
* Important : Windows VISTA users need to make a change to their system to successfully use many ROM packages. See Mr. Vanx's guide here
*
If you are using Windows XP or Windows 2000, you MUST have the Microsoft .net framework installed on your computer.
1. Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
2. Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
3. Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
4. Open mtty.exe and select "USB" from the dialog box, then hit Ok.
ciaoo kB
Click to expand...
Click to collapse
when i go to step 4 and hit OK, the mtty popup a dialog box said "USB port can not open"
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
ocguru said:
Have u tried hard resetting your phone? or maybe u can just go to bootloader mode and flash it with a new rom? this work for me
Click to expand...
Click to collapse
really? i haven't try , i am afarid it will become more serious
but what is your problem previously? why you bricked your phone?
i was trying to upgrade HTC offical ROM and bricked.
THX
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
ocguru said:
as u can see..there are quite a few rom..i had to try every one of them to see which one suites me well..thats how i got my phone bricked
Click to expand...
Click to collapse
i read this post
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
my hermes is same as the bottom situation of the above page now
SPL2.03,no boot OS, no GSM, bricked while flashing OS, but my hermes
can not switch to KITL mode , so i have no any idea
do you have any suggestion for me?
THX
turn on your phone..connect your usb cable..see if u have any connections with activesync..
ocguru said:
turn on your phone..connect your usb cable..see if u have any connections with activesync..
Click to expand...
Click to collapse
sorry , but it has no any boot OS thus Activesync can not recognize my phone
Apologies but have scoured all the threads and cannot seem to get to a straight answer!
Have a tocuh-dual which I attempted to update to the latest ROM from HTC and now I have the "tri-colour screen of death!) and can get no further,
The screen shows in thered band - RUUNBH | NIKI100 | SPL-1.16.0000 | CPLD-4. The white band shows "serial" and when I connect the USB lead it shows "USB".
But the PC does not recognise it at all and when I try to load a ROM or run MTTY nothing is found. How can I run a program on the touch if the PC will noit see it through the USB connection?
Any ideas?
Does your PC have active Sync installed? I had a similar problem when I installed a broken rom that would not boot up. I did a device reset using the stylus in the whole next to the USB, while holding the camera and power button to boot into the tri color screen. Once hear i plugged in my USB cable and ran a ROM install.
I hope this helps.
uncheck allow usb-connection in Active Sync
run mtty connect by USB
type "boot" without quotes.
same problem
i have got the same problem and can't get out of the tri-colour.
I try to connect with mtty and it says usb port cannot open. my pc can recognise it and in da phone it shows usb though, i don't really know why its not taking. if i type "boot" in mtty what will happen? cos when i click on com3 its opening but when i write "boot" nothing happening even with boot. any ideas guys? how to solve the problem????
Regards
u have to unckeck allow usb connection in active sync! then u can connect with mtty
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
use xp
bodonline said:
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
Click to expand...
Click to collapse
Use xp mate, cos vista has got some problems. normally for unlocking and upgrading i use xp. blow up the vista .
Regards
I will crank one up and let you know how it goes!
kill the task in the Task Manager... then u can connect with mtty
Tried killing the process but MTTY still says "USB port cannot open" - no idea what else to do?
If any Program use the USB Port ... no other Program can use the USB at the same time!