Hi!!!
I have found in SPV C550 J-tag pins.
Up
1-NTRST
2-TMS
3-TCK
4-TDO
5-TDI
Down.
Pin are in BLUE-LABEL.
Foto is T-Mobile SDA (Sonata) but pins I searched in SPV C550.
There SPV is without processor ;>
Greetings from Poland
Great find!
Thanks a lot and... pozdrowienia!
Fajnie jak się przyda, poświęciłem swoją "latarkę"
are that jtag pins have any connection with display message "data crashes. contact your service" on my spv c550?! Are they broken or somthin' cuz some guy tell me that i must change them to fix my problem?
Did someone try this?! Are the points ok?! I am going to flash my hurricane through this JTAG points so i'm not going to suprise me if something didn't worked ok?! And, is the WIGGLER cable ok for this, and if someone have bootloader and all need software for the JTAG flashing!? I will be thankfull!!!
who can give a complete guide how to make it work for a typhoon . now i use a wiggler cable can communicate with my typhoon, also can load a .nb file ,but how can i let my typhoon into the wish bootloader, my typhoon is in using now all is ok i just want to test how to change the SPL version via jtag method,everytime i loaded the SPL nb file ie.064, clicked run--go from--10000000---ok,if i hold the camera button the phone just white screen nothing happen cannot detect by mtty,if i dont hold the camera button the phone will startup nomally into wm6.1.
can somebody give me some help?thanks very much!
Related
Guys, I'm frustrated now. I've refreshed the ROM of my G4 version of Dopod 818pro (2.15.0001 or something I just can't remember). Unfortunately it fails and I cannot even turn the power on. My WinCE colleague told me that the Boot Loader was damaged. I am now seeking for some place to re-program the chip and hope if someone can provide me boot loader program. I really appreciate your guys help!!!
Are your Bootloader Realy damage? You mean you cant enter it? Or you havent Power to start your Device?
SD Flashing doesnt work without Bootloader!!
JTAG Flashing (hardware nearest Flashing!!) isnt developed for G4 Plattform. (i think so ... look in the Wizard board ... they talk about JTAG flashing and Wizard G4 must simulare like Prophet G4!!)
the bootloader really damaged, I cannot enter the three stripe screen by holding CAM, PWR button and hit reset hole. Do you mean that I even cannot use JTag to burn the chip???
I do have two fully charged batteries. But it should not be a problem of battery, I tried to connect it to charger but it gives no response, no LED
Using JTAG to revive a wizard is either a myth, or an undiscovered secret. If you cant get into bootloader, your chances of reviving your device are slim.
JTAG isnt a secret ... its more like ... hardware knowlage. If you know what IC is your ROM. You can found over the IC Spec the right Pins for JTAG Programming. If i can get a G4 S200, i can try my best.
yes, I know that using Jtag to rewrite boot loader is complex, but it seems like it's my last chance. NetrunnerAT I really appreciate your help but I'm in Shanghai, China so I have to find someone locally who can help me with that. Wish me good luck and I'll keep you guys updated about the result
If I can find someone who can help Jtag my phone, where can I find the correct bootloader program for my cell? is it downloadable?
guys, I finally found a place to revive my prophet. However, they don't know how to jtag it either, neither do they have a programer to rewrite the chip because they say the programer is very very very expensive. They just changed the old chip with one which has correct ROM and now my G4 Prophet turns to a G3 one...anyway, I can use it now.
Thx!
You have change your rom and it is now G3!!
Can you say me what IC they have exchange! If i know it ... and get a damage device, its possible to found a solution for all Prophet users!
No problem, I kept the damaged IC at home, I'll check the model No. and will let you know
er... One more question, I want to dump the current ROM to my SD card, however the wiki doc says it needs to unlock G3 first. But another doc also says unlocking G3 will downgrade my OS to 1.0.13.21. It's like a kind of deadlock, can I just unlock G3 without changing OS?
uhm ... i think you must downgrade your OS first to CID unlock ... after that you can upgrade to your rom and make SD-Dump!
ok, then that is to say i'll never be able to get a backup of the ROM I currently have.
I'll wait for some weeks and will try to "torture" my prophet again. It was just fixed and I'm supposed to "rest" it for some days, but sooner or later it'll be unlocked, hey heyhey....
Hi, I'm back, the chip is a "M-System MD8832-d16-v3-xp" with a clearly name "Disk On Chip" on it, hope this can help you locate the chip
http://www.m-systems.com/NR/rdonlyr.../0/EOL_DOC_G3_P3.pdf|EOL_DiskOnChip_G3_P3.pdf
Cool ... i read some PDFs ... this is are very nice entry in the PDF!
Compatibility Issues
The recommended replacement, DiskOnChip G4 1Gb/2Gb 9x12mm FBGA, and H1 2Gb
12x18mm FBGA are ball to ball compatible with DiskOnChip G3/P3 7x10mm, 9x10mm FBGA
products that are being discontinued. It is necessary to upgrade software based on TrueFFS 6.2.x
to TrueFFS 6.3.2 and above when upgrading to DiskOnChip G4.
If the different betwen G3 and G4 is the TrueFFS Driver and the G4/H1 is Pin Conpatibel ... possible if i get a half damage device i try to solder a H1 DOC on the PBC and reformat it.
[edit]Holly ****! THX i have found the Migration Document with JTAG Pins!!!
http://www.m-systems.com/NR/rdonlyr...MigrationGuideDOC_G4_1Gb_to_H3_1Gb_Rev0.2.pdf
how are you going to access the pins on a FBGA?
yanuk said:
how are you going to access the pins on a FBGA?
Click to expand...
Click to collapse
you dont. you take a bricked one, de-solder it, and manually trace them to somewhere on the motherboard using a multimeter.
can any body help me with a jtag points for a g4 wizard doomed with a incorrect ipl
Give me a damage Wizard board and i say the JTAG Pins! G4 and G3 have the same JTAG Pins.
I search for a damage Prophet to but i doesnt want pay over 80€ for a community project without any payment. It some on give me a wizard or prophet Board ... i desolder the IC ... search for JTAG Pins ... and reflash it ... send it back but working :->
the device doesnt damage if i resolder the DOC ... i have the right soldering mashine.
NetrunnerAT
Where you saw on DOC points jtag ?
You need the signals TDO TCK TMS TRST TDI.
DOC only memory and there no these signal.
What jtag you will use? And no program for flash DOC through jtag - see about Universal jtag.
If anyone can help me I just brick my ameo. I download olipro unlocker followed steps had everything done but after i finished the 1step it wont boot up again its just dead. tried hard reset alot of times wont even go pass it . it just light green.Pls help
Can you enter the Bootloader mode?
Press Camera Button (completely) and hit the reset button at the same time.
i know yor problem press cambutton and powerbutton for at same time so you will come to the bootloader modus now plug in your usb cabel to your device and your computer now open the image of wm6 that you want to install the setup will find your ameo now
hope you will get it
good luck from germany and sorry my bad englisch
Thank you that Fixed it. I just panic but now the whole process was finished. from 1-3 now. thank you for the reply
please help.
I have the same probleme and i can´t enter the Bootloader mode.
remove sim and storage card then do as mosho said
ie press camera, comms button and reset button then restore original rom , then olipros program
as per the wiki
http://wiki.xda-developers.com/index.php?pagename=Athena_Resets
cant get into bootloader
hello,
i cant get into bootloader at all.
i removed the sim and the memory card, al i get is a short flash of red light t the joystick, and only if the device is connected to the power cable.
it doesnt charge, it does nothing. i tried really everything.
does anybody have an idea?
thanks
mike
try a service exchange at t-mobile. there seems to be something wrong with your device.
my ameo had no probs running olipros unlocker.
regards dieter
i used the unlocker with another ameo i bought, and it worked fine.
so i tried the same with the 2nd, and it crashed.
will they find out that i tried to unlock the device?
regatds
mike
ameo dead
Hi mikekarl
we have the same problem that happened to me today.
i have done it before with another ameo worked fine.
Now i cant get into bootloader or Hardreset.
and i cant try a service exchange because iam not t-mobile customer.
Pls help
First I was using WM5, then I decided to WM6 ROM update and tried "nhocbanme PDAVIET WM6 for HP iPAQ rw68xx ROM", everything was OK, it worked well, after, I have decided to change it with Garmin 03.02.2008 Kumara TOUCH WM6 Premium- (OS CE 5.2.2000 Build 20000.1.0.0) ROM, I put the files of Garmin's to the MiniSD card, then pressed the soft buttons to make my ppc bootloader mod. However, it resetted, the I pressed the soft keys again and it closed with white screen, I think I pressed another button while pressing soft keys, ı could not understant. It still turned OFF and I am not turnin it ON, I tried lots os button combination but it did not work My battery is full and I connected it to my laptop by USB cable, but it did not see my PPC coz it is closed could anyone help me about this case?
please help me what do you suggest me?
Try to disconnect cable USB, to pull out a battery (for some minutes) and to pull out a card miniSD. Try to come in bootload, learn all methods. If it will be possible, start on a laptop native insertion WM5, connect the device and burn it. Then stitch worker WM6 if is. If nothing will turn out that collect JTAG a cable, and reanimate.
sugermas said:
Try to disconnect cable USB, to pull out a battery (for some minutes) and to pull out a card miniSD. Try to come in boot the menu, learn all methods. If it will be possible, start on a laptop native insertion WM5, connect the device and burn it. Then stitch worker WM6 if is. If nothing will turn out that collect JTAG a cable, and reanimate.
Click to expand...
Click to collapse
Thank you very much for ur information bro,
sugermas said:
start on a laptop native insertion WM5,connect the device and burn it. Then stitch worker WM6 if is.
Click to expand...
Click to collapse
you said that, how can I do this? could you help me?
At me rover g5, clone Atom EXEC, on how many I know your device - close brother Atom EXEC.
You have native insertion WM5? If there is no that download it.
It is possible to come in bootloader? If that is possible come into it, start Device Software Update Utility.exe (or the similar program starting ROM UPDATE), connect the device to USB, and burn. I do not recommend to be stitched from card MiniSD.
sugermas said:
At me rover g5, clone Atom EXEC, on how many I know your device - close brother Atom EXEC.
You have native insertion WM5? If there is no that download it.
It is possible to come in bootloader? If that is possible come into it, start Device Software Update Utility.exe (or the similar program starting ROM UPDATE), connect the device to USB, and burn. I do not recommend to be stitched from card MiniSD.
Click to expand...
Click to collapse
I could not come in bootloader, this is my problem :S my PPC is not working.
kumaranın romu 6815 için değil yanlış yüklemişsin, bataryayı çıkart 5 dakka bekle resete basılı tutarak bataryayı tak
ama 68xx yazıyor ilgili ROM da. dediğin yöntemi de bir çok kez denedim ama olmadı :S yarın servise götürcem :S JTAG ı beceremem diye düşünüyorum :S
-------------------------------------------------------------
Is there anyone who could help me?
bootloader ini bozmadıysan jtag e gerek yok, kumaranın romunda bootloadere geçişi farklıydı galiba, ona bir bak.
bu arada kumaranın neresinde 68 diye yazyır ?
Englisch forum
This is an Englisch forum.
b3kturk said:
First I was using WM5, then I decided to WM6 ROM update and tried "nhocbanme PDAVIET WM6 for HP iPAQ rw68xx ROM", everything was OK, it worked well, after, I have decided to change it with Garmin 03.02.2008 Kumara TOUCH WM6 Premium- (OS CE 5.2.2000 Build 20000.1.0.0) ROM, I put the files of Garmin's to the MiniSD card, then pressed the soft buttons to make my ppc bootloader mod. However, it resetted, the I pressed the soft keys again and it closed with white screen, I think I pressed another button while pressing soft keys, ı could not understant. It still turned OFF and I am not turnin it ON, I tried lots os button combination but it did not work My battery is full and I connected it to my laptop by USB cable, but it did not see my PPC coz it is closed could anyone help me about this case?
Click to expand...
Click to collapse
It seems that you have not read the first post of the thread properly. nhocbanme PDAVIET WM6 is for your unit that is why it worked for your HP6815. As stated above, you have switch to garmin KUMARA TOUCH WM6 Premium which is for XDA ATOM(black) and ATOM PURE(white) only. If only you have read carefully and understand the thread before doing the update procedure you may still have a working device.
This may be a case of ANOTHER bricked device because of not READING properly. That is why it is stated in the first page of the thread for what device can the ROM be used. You may try to check the wiki if you can still revive your unit. Although the JTAG of the HP units are different from the ATOM. Good luck mate
hprw6815 keep self reset BL FF.FF.FF
have earlier update with Ver2.02.01b_byNHOCBANME i was very happy with it but bt handsfree didnt worked so i tried 6828-WM61-20080920-b165.tarminisd then i couldnt update back i changed bl to HP BL1.0.1 with out success i think my devise is ****ed up... i appreciate if some one can help me
Will this break my c550?
Upgrading my gsm to wm6 gsm?
Check the screenshot......is hurricane the same as typhoon?
Cheers,
HJ
Hurricane isn't the same as typhoon.
Hurricane = SPV C550
Typhoon = SPV C500
I don't think it will work.
Ok, I aborted the upgrade; is there a radio upgrade for the hurricane?
I bricked my device, I tried it because my speaker was not working....but this upgrade really does brick your device.....
Cheers,
HJ
Can you get to the bootloader (bootloader = three colored screen) ? (Press and hold the camera button, then insert the USB Cable) ?
If you can, then you can easily upload a working ROM with MTTY
ThinkPad-User said:
Can you get to the bootloader (bootloader = three colored screen) ? (Press and hold the camera button, then insert the USB Cable) ?
If you can, then you can easily upload a working ROM with MTTY
Click to expand...
Click to collapse
Nope, it is a genuine brick, nothing can be done.......
Anyone interested in a c550 for spare parts?
Sure nothing can be done? I'm willing to help were I can. living in the same city...
Have you got AP 4.0 allready?
xvanwaart said:
Sure nothing can be done? I'm willing to help were I can. living in the same city...
Have you got AP 4.0 allready?
Click to expand...
Click to collapse
Het is een echte baksteen......
Nope, nothing can be done.....it's a genuine brick.....
And still waiting for AP 4.0......
Maybe U can use it for spare parts....
HELLO
i am a new member and sorry for my bad english
my problem that i ve upgrade my hermes and unloked sid ,but i killed my Hermes by trying to fix a "NoGSM error"
now my hermes don t start i can 'thave the boot screen ,only if take the power botton +to access boot screen i traid all solutions but no success
i ve not access to ktl mode;for this resons i supluy your help,i have connet herms and launch device monitoring and officiel rom ,result is attached down,
herm200
IPL 1.04
SPL 2.03
THINKS
Hello STAMBITA, try with mtty for fix problem.
If your OS don't start you try JTAG mode because your Hermes is not super cid (SPL 2.03) for fix problem.
See the post http://forum.xda-developers.com/showthread.php?t=391047&page=17.
Regards
nico
STAMBITA do you have access to a rom provided by your telco? If so try to flash that rom while you're in the bootloader. Since your device isn't supercid it's either that, or JTAG or send it to a repair centre. I'm sorry.
I ve not access to room .with mtty nothing happen nothing .the last solution is to try jtag but is complicate to do.to send for repair centre it cost the price of new one?