I cant get to bootloader mode by camera+reset.
all my o2 atom life does is soft reboot then start wm again.
i've alrdy tried hard reboot and reflashing to the original rom from o2.
help?
Nevermind, i found out that its supposed to be the voicerecord button, not camera button, and the usb has to be plugged in b4 reset.
delete post
Related
Hi!
I downloaded a dumped German WM6 Rom. Now I have a big problem. I turn the device on, and the normal HTC Logo appears.
After that, the Qtek Logo appers, and that is all. After the second Logo nothing happens. What can I do?
I tried a soft reset, the same problem. (Reset Button)
I tried a hard reset, the same problem. (Camera, Comm-Manager, Reset)
I tried the same with the Camera and the Reset Button without the Comm-Manager Button. Is it possible to get a running system back? I made a Backup long time ago, so the files can be deleted.
Thank you very very much.
Enter bootloader mode, connect the usb cable and flash back to original WM5 rom.
Hi!
Damn, I used the wrong update. Thanks..
i have tried install chiense wm5 3.5.2 akuu and now my boot loader dont workin first says usb error and i tried try instal new one boot loader with memory stick but now bootloader totaly crashed no workin no cant see colores screen
i have tried found in forum but a lot topic
and sorry for low english
1. take out yr battery from yr atom for about 1 minute
2. press the camera button and the reset
3. load the AKU 3.3.3 or the original O2 atom software
Violalie.. and waiting for 20 to 30 minutes as it will flash.. Good Luck mate.
dude thx for info but it didint work i did take out battery sim card and memory card 12 hour still cant enter boot load only a black screen comin and goin
Try the following:
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode.
Taken from http://forum.xda-developers.com/showthread.php?t=314613
ehm didint work what should i do
can i change bios my atom
Your bootloader was destroyed and you can only send your device to service.
1) your devices can boot up and use well?
2) did you mean that even if you try to hard reset your devices, it wont goes to boot loader mode?
3) PC cannot detect your hardware when you goes to boot loader mode / WM5 mode?
Did u try copying aku 3.3.3 image file in memory card and try boot loading?..
no i didnt try because my boat loader no workin cam+reset and volume+rec+reset dont working i cant load anything
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks.
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks
Click to expand...
Click to collapse
dude its only resetting phone taking factoty settings no i didint i am readin now
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
vhd99 said:
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
Click to expand...
Click to collapse
Your atom is still live.. check out below thread .. how they recover a dead atom..
http://forum.xda-developers.com/showthread.php?t=314613&page=76
http://forum.xda-developers.com/showthread.php?t=314613&page=77
http://forum.xda-developers.com/showthread.php?t=314613&page=78
what mean hard reset
ok i got what hard reset i did hard reset but still no goin boot loadin i tried all methods
It's NOT hard Reset.
1) Remove the battery for at least 1 min.
2) Take back the battery in
3) Press the Camera Button following with the pin hole(reset button)
I had wm6 on it, prophet touch 4.0.0.6 and i tried now to install IX version, and after first install i made reboot and doesn't start anymore (. It's stucked in HTC Prophet Touch from beginning, and is showing in left corner ILP SPL..etc...in bootloader i can't enter (doesn't appear anymore). what should I do? It's a G4
Did you TRY to enter bootloader yourself??? I haven't quite understood your post. In case you didn't:
Press Camera + Soft Reset, then release soft reset and keep pressing camera button till bootloader appears.
yes i tried that. I've pressed camera+soft reset and holding camera..and nothing happened.
yes i tried that. I've pressed camera+soft reset and holding camera..and nothing happened.
solved. it was from my SD card. i've get it off and now is working: entering bootloader, installing ROM. thx anyway.
Hi,
I'm a hp rw6828 user and is very much enthusiast to try out those wm6 roms made by those experts. However, i did a mistake while trying to flash.
I tried flashing with a rom from wantat but i forgotten to delete the EBOOT.nb0 before i clicked "upgrade". Then the program stopped at 6% for a long time and didnt move. I disconnect the cables and tried to turn the device on.
THe device can go into the wm6 and the start button can be use but the screen is "moved" to the right side and other function is not working.
After that, i did a hard reset and the the os seem to work like normal. However, when i tried to go into bootloader mode by pressing both "_" and soft reset. That didnt work. I tried another way by taking out the batt, leave it for a 10mins, press both "_" and soft reset, put in batt, release soft reset then "_" keys. That didn't work either.
But, just lately, i've tried taking out batt, holding the camera key and softreset, place back batt, release soft reset n camera button. This method works and i get what it seems to be an atom bootloader?
i get a black background with "MN1 Bootloader Mar 29 2006 13;52;14 copyright..... 1) debug module through UART 2) jump to DM Enter your selection.
Can someone help me? I'm not sure what i'm facing and what to do? All you help is much appreciated. THank you.
i installed a new rings rom. it worked fine, then my phone froze up, now it won load pass the opening page. it just says analyzing device component..... and its frozen there. please help, i run my company thru my phone and its very important...
what type of phone do you have? if its a G1 as i have then its easy to un-brick or un-lock...just plug your phone to your PC and format your sdcard again which will erase all of its data then ya good to go or you can remove the battery place it back then hold down your home plus power button at the same time till youir phone boots to the next screen then press alt+L then altW then reboot your phone and sign back in...
if this is a post about the g1 take it to the other forum because this is about the hermes
its a herm 100. htc 8525
have you tried to do a hard reset? If not give that a try.
I hope you installed Hard SPL V3 on it first... to check - hold power, OK button above the flywheel and reset with stylus, hold in until the tri-colour screen appears. Will show IPL - 1.04 and SPL - 2.10oli (if you've installed hard SPL V7).
If so, and you tried to Hard Reset 1st with no success, try the sd card method. If thats not working, on the pc, if using XP, go to activesync's connection settings and untick "Allow USB Connections". Connect your Hermes to the pc with usb after going to bootloader. Run the RUU_Wrapper.exe file again. This should re-install the rom.
You're gonna have a heap of trouble if you haven't Hard SPLed your Hermes.
Good Luck....
I dont have hard spl v3 on my phone. when i try to load another rom or anything i get error 270 the image file is corrupted. please check your update utility. what does that mean? and how can i work thru that?