Related
Here's something weird...
I have an early model PH10A XDA II...
was on ROM 0.81.00 USA
Radio: 1.05.09
Protocol: 1337.10b
Date 8-11-03
I'm trying to upgrade it to the latest i-mate ROM.
I have gotten to the point where it says "The current software is now being erased....the update should take 30 minutes." but the first time...it gave me an error and it asked me to reboot the device and try again...since then...
....it stays there for hours with no update, no errors, or feedback of any kind. All I get on the RUULog.log is "17:24:10 Connection with USB"..then nothing happens...
I have tried re-boots, hard boots, taking the battery out and waiting a few mins, making sure the battery is charged, I'm on XP and the latest Activesync 3.7.1, also I kill the wces...exe. app and still sits there..
I have tried the O2 version, the UK-02-version, himalayaupgradeut_197.exe...all to no avail...
Any other things I should attempt? I'm bootloader 0.23....
I'm still scouring the groups to see if anyone had this problem..
thanks!
re:Weird problem with early model HTC XDA II with 0.23 btldr
Thanks to these posts I can safely say I found a partial solution that works. From other similar posting, it seems the early bootloader 0.23 was a pre-release demo and not for public consumption...so this USB upgrade process does not work for this version.
What worked for me using this bootloader version was a combination of the posting here http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=93&PN=1 - using their choice #3.
1. Download ROM 1[1].72 SD.rar (ROM 1.72)
2. Extract ROM 1[1].72 SD.rar with WinRAR, you will find two files; ntrw.exe and ROM.nb1
3. Put them in any folder; say c:\ROM\
4. Go to DOS command and the folder contains the files
5. Type C:\ROM>ntrw write ROM.nb1 E: (Assume your card reader drive is E as shown in the below figure. Wait until finish writing the rom.
6. Put SD card into your XDAII, go to bootloader mode (Power + Reset + Directional Pad) and follow instruction on your device screen.
However, for this bootloader it definitely wanted a RAW formatted SD card, not a card formatted by XP/2000 card readers. I also tried other devices format Treo 600, etc...but what did the trick was to do a save to SD command using the USB/Serial program ROMUPDATE.exe located somewhere on this board.
This allowed the card to work with the bootloader...
Once this was done...I was able to insert the card on the card reader (and get an error - ingnore since it was raw format)...and type step #5.
Once this was done I was able to boot the device again.
To note..most of the solutions posted here work for public release bootloaders above 1.0...but this was an early release bootloader...and this is how you get this one to work. NOT using USB.
Now the next task is ...how do I upgrade the bootloader?
pda t-mobile mda ph10a
hi i have an old pda ph 10a ,and i want to know how to hard reset device, when i pres (power,navigation key ,and reset) mesage apears on screen says( serial v1,06) and nothing hapens
does anyone know how to reset and try to restore setings from pda (its on a german ,so that is more dificult)
removing SD card from device should solve your problem
pedjaar said:
hi i have an old pda ph 10a ,and i want to know how to hard reset device, when i pres (power,navigation key ,and reset) mesage apears on screen says( serial v1,06) and nothing hapens
does anyone know how to reset and try to restore setings from pda (its on a german ,so that is more dificult)
Click to expand...
Click to collapse
for hard reset u need not to press the navigation key just press power and reset.
and if this does not help try reinstalling the rom in boot loder mode(serial 1.06).
I'm new to the whole Hermes upgrading scene - but have read just about every forum thread and post on upgrading. I'm trying to follow this process:
http://forum.xda-developers.com/showthread.php?t=312943&highlight=vista
I chose to upgrade via SD card, since my windows box is a vista machine and I primarily use my mac day to day. Here's the problem I'm having - when I try to flash HardSPL V7 via the SD card (using the filename hermimg.nbh in the root of the SD card), it starts to say "loading" in bootloader mode, but then flashes up "00068002" in red at the top of the screen, and then continues into normal 3 color bootloader mode.
When I try to do the flash from vista with RUU (after following the guides showing how to downgrade to the XP drivers), I get a 262 error, and when I look in RUU.log, I see the following:
00:24:27:674 [msg] : Version : [5.10 - 20060412].
00:24:30:851 [msg] : Current Not in CE Mode or in CE Mode but ActiveSync Not Connected.
00:24:34:879 [msg] : Disconnect ActiveSync .... [0]
00:24:34:880 [msg] : Start Get Connect Port.
00:24:35:025 [msg] : Current in BL Mode. Open Port : [\\.\WCEUSBSH001] OK.
00:24:43:512 [msg] : Device BL VER : [1.04] [].
00:24:43:522 [msg] : =============================================
00:24:43:524 [msg] : START GetNBHInfo !
00:24:43:525 [msg] : END GetNBHInfo !
00:24:47:310 [msg] : Check Ac in BL mode. AC : [1]
00:24:47:314 [msg] : IsBL. BL : [1]
00:24:49:363 [msg] : =============================================
00:24:49:384 [msg] : START UpdateNBH !
00:24:50:577 [msg] : Upgrade 2 : 0 Start.
00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002.
00:24:52:040 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:790 [err] : Receive Data Error : 0x708, 0x00018002.
00:24:52:791 [err] : Write NBH Data Error.
00:24:52:793 [err] : BL UpdateNBH Error.
00:24:52:821 [msg] : START UnInitialization !
00:24:52:843 [msg] : END UnInitialization !
Notice the line "00:24:51:310 [err] : Receive Data Error : 0x713, 0x00068002." - that 00068002 is the same number that pops up when trying to flash from the SD card.
Same exact thing happens when I try to flash anything else (like a radio rom, or an OS rom).
Any help would be greatly appreciated!
PS: my TyTN shows as a HERM200, IPL 1.00, SPL 1.04
Did you format your SD Card in Fat32?
The most common problem when flashing from card is a wrong formated card.
yes, i formatted it Fat32 and also did a chkdsk on it.
Did someone get the solution for this?
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
I have problem flashing using Sandisk 1GB, formatted FAT32, .nbh in place, after tri color bootloader nothing happen, no 'Loading'. Anybody experience this problem?
When I use micro SD 256 MB (from Nokia), no problem at all, flashing process Completed.
Is SD capacity (too big) become an issue or is this bad SD card..?
some sd cards cant be used to flash roms, i dont know why, maybe someone else can explain why
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
ultramag69 said:
argupas, did you rename the .nbh file to "hermimg.nbh? It MUST be renamed to this for sd method to work. cheers.....
Click to expand...
Click to collapse
I already rename .nbh to HERMIMG.nbh.
I think it was SD card problem (1 GB Sandisk, I suspect a fake one), because I am now using 512 MB V-gen, no problem for flashing.
Thx.
koorosh_bsboys said:
Why you people do not search before making posts?????!!!!!!
Here is what u asking for :
1. Format your SD card with FAT32.
2. Download Hermes SIM CID Unlock v3a.
3. Copy SSPL-HERM to your SD card.
4. Extract the RUU_HERM_Unlock_v3a.
5. copy HermesUnlocker_HardSPL.nbh to SD card.
6. Rename it to HERMIMG.nbh.
7. put the SD card into the device and run sspl.exe.
8. the device enters the bootloader and ...
Click to expand...
Click to collapse
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe. And also if enter the bootloader, I can press Power+OK+soft reset. Is this right for enter bootloader or i must run sspl.exe?
you have to run SSPL.exe from the file explorer. It has to be run from the PHONE memory, NOT the sd card.
Try a hard reset, both soft keys and reset with stylus. Hold all buttons until it asks if you wish to reset to factory (or something like that, you get the idea). Push "r" on slideout keyboard then "space"key. you now have to go through the alignment and everything again.
Even if you use this method, make sure you install Hard SPL V7. It is safer than anything else. You should also have checked what radio rom you were using as it has now been downgraded to 1.116.x.x, this may cause you some trouble later too.
Use the sd card method to fix this as it appears safer than using the pc. Just make sure you have got Hard SPL installed and have a charged battery. DON'T just think you can put it on the charger while flashing AS IT DOESN'T CHARGE...
Cheers...
Sorry to replay this thread but i had a situation like that.
I have a Hermes, with the pin of the USB that makes connection to PC broken... So my only Shot to update the ppc is from SD. The rom i have is one of 1st realeses of hermes wm6.5, so that stucks all the time, even i hard reset it...
When i try to update something from SD i cant because gives me that error 000602... Any idea? So i have to unlock the cid, but if i cant access to the windows what i must do?
If i hard reset it, it enter in windows, but 2 ou 3 seconds that stuck :S
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
ultramag69 said:
If you can't get into windows to run SSPL.exe to install Hard SPL & your USB is stuffed so you can't connect to PC then you have a brick... If you had Hard SPL installed 1st then you wouldn't be in this situation.
Sorry, you have a brick unless you fix the USB connector.
Click to expand...
Click to collapse
Ok, but if i fix the usb... updating by bootloader mode and usb, i will not get the error 00068002?
Not if you install Hard SPL 1st...
I dont understand 7th step. Now my device hang in "Windows Mobile" screen, so how can I run sspl.exe
Click to expand...
Click to collapse
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
aladin said:
same me too,
My device Stuck on bootloader, Why can I run sspl.exe?
Need Help
SOLVED:::::: sorry
Click to expand...
Click to collapse
First off, reflash your device with your phones original carriers ROM. Your phone will accept it. It sounds like you didn't SUPERCID your phone first, and didn't HARDSPL your phone.
Make sure you HARDSPL then SUPERCID your phone FIRST!
Download your phone's original carriers ROM and flash that via SD card to your device. That should return it back to "factory" state, and get it so that you can once again try to HARDSPL and SUPERCID your phone.
Hope this helps,
Cheers
Supercid then Hard SPL... If you run the V3a unlocker it flashes your SPL to 1.40... Hard SPl V7 is the latest and greatest. Technically you shouldn't need to supercid your Hermes after Hard SPLing it.
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
3351405372 said:
Hi
your instruction are really complete and clear but . . .
but my TyTn to day has a problem (better I have a problem!!)
After breaking the flash of a new ROM (it was corrupted) it either stays in bootloader mode (IPL 1.01 SPL 2.03) or,after few seconds from booting and displaying all data like
M 05 R 1.56.70.11
S 04 G 32.89.7020.20H
B 06 D 3.57
turns the display full white, make a "ding" and never enter into W.M. 6.5. Hence, how can I launch HERMES-SPL.exe ???
Other attempts to flash from PC through:
- RUUWrapper provide up-date error for missed USB connection
- <ROM>. exe the flash starts but stops after few second when the status bar, on the PDA reach 1%.
So, it became a brick?? There is any chance to retrive it?
Click to expand...
Click to collapse
Hey bud, if you hold the POWER BUTTON and the CAMERA button down and hit the RESET button, do you get a tricolour screen?
If so, then your phone is not bricked, just has a failed ROM on it.
You can flash via SD card onto your phone, and to do so, download the rom for your network, the one that originally came with your phone, onto your phone. when you put it on the SD card, make sure you name it HERMIMG.nbh. This'll allow you to flash via SD. put the card in, reset to the tricolour screen, and then follow the instructions for flashing.
Once this is done, you can then attempt again to SuperCID your phone.
Cheers!
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
donot ever try thru SD card.. there is a chance that you may brick your device.
Goto bootloader mode first then u run DSUU.
Now after i did that, it dosent work with DSUU .it show "error connection".and my divice shows the upgrade fail
How many files you have in the upgrade directory? Normally it should contain 6 files:
- Device Software Update Utility.exe
- diskimage_Ver.nb0
- EBOOT.nb0
- ExtendedRom.img
- nova_pda_033105.mot
- vl1d_pda_Ver.mot
It will always shown connection error if one of these files is missing
I have all of them,
It seems feasiable to full downloadig the Rom from SD(memory card), but i need mor files:
"diskimg.nb0 , eboot.nb0 , dm.nbo , flash.img , agent.mot , mot.mot , CPLD.img , assetInf.img , extended.img , Mdoc.img"
If it's possible to upgrading with them how can i rech them ?
hello...!!!?
can enybody help me with this case? I need Your Help. Please. . . .
shaemna said:
hi
I need your help to fix my O2 Atom Exec.
i wanted to upgrade my ROM in to the WM6, at the bigining i copied the "diskimage_Ver.nb0" & "EBOOT.nb0" on my memory card. and got my Atom Exec into the bootloader , after download complited the LCD got dark, i got it on bootloader and start the "Device Software Update Utility" and clicked on "Next" until "Upgrad" was shown.When I clicked on "upgrade" this error was shown:"CONNECTION ERROR" . What should i do to fix it?
Thanks.
I'm looking for your answer.
Click to expand...
Click to collapse
Why did you do this?! No one gave out instructions to flash anything using SD CARD in the first place! Of course you will get connection error because bootloader is not functioning. Remove your SDCard, start bootloader mode, and flash the normal way.
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
shaemna said:
I did that but it's not worked. and got me "error connection", i saw some where that if i do it in the that way (with sd) it's worke and beacuse of that i did it in that wey, now what should i do? how can upgrad my ROM or downgrad it, my divice is alredy ded, how can i get it alive? help me
Click to expand...
Click to collapse
can you go into bootloader mode?
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
shaemna said:
yes it's go to the bootloader but when run DSUU plase of the last version of the rom and radio is empty, when i click on UPGRAD it get me ERROR CONNECTION
Click to expand...
Click to collapse
I'm sorry. I don't get you. You can go to bootloader, but you get an error. Can you post a screen shot of the error? so, I will know what to do.
How can I uplod picturs?
server is busy it get me Network Error (tcp_error) and cant upload it
the doucument of it is:
(the upgrade page)
Your Divice software is about to be update from:
divice CE image version:0
divice Radio image version:
to:
CE image version: 7210621
Radio image version: R060711N-MN2ARC-RS00011
.......
PLEAS CLICK update to continue
when i click upgrade it show me the fowloeeng error
ERROR:CONNECTION ERROR
THE DIVICE SOFTWAR UPDATE IS HAVING TROUBLE CONECTING TO YOUR DIVICE
PLEAS CHEKE
1)YUOR DIVICE IS PROPLY CONNECTED TO THE USB CABLE OR ...
.
.
.
now what should i do?
do you have any other USB to mini-USB cable? try changing it... The ones used for SD Card readers or Digital Cameras are the same, and do it again.
i do that in all of my USB ports and they are same and get me error conection again
Is there any wey else to inistall a ROM on my divice?
1) Is windows recognizing your device?.. (Do you have activesync installed?)
2) Did u try using different USB cable ?
3) Are you logged on as administrator?
4) Did you remove SD card before going to bootloader mode
5) What is the screen content when you go to boot loader mode
6) Before connecting the device go to bootloader first, then connect the device and then run DSUU
7) Activesync may install device drivers for your device so try installing activesync?
Thanks
when i get my divice in to the bootloader it's display:
===========MN2 Bootloader=
Jun 13 2006 20:41:44
copyright (c) 2006 Quanta cor
poration
CPLD Ver: A0060109
***********************
*Using '<-','->', 'Enter' *
*to choose what you want *
***********************
(1)debug module through UART
(2)jump to DM
enter your selection:
when i conect it to pc( as administrator user) the fallowing line was shown:
USB connected , waiting for download command...
and my computer beeping and found new hardware but not connected to activesync(4.5) , then i start DSUU and when start to upgrade computer show me "ERROR CONECTION" and my divice show me this note:
! ! ! Please use DSUU in OS mode and sync with pc first ! ! !
Usb transfer Fail
please help me
1. We get the most first sewing of Xda-atomexec-eng-20060614_r060428n_ex0028.exe (only by this sewing restore was able)
2. We drag out the files of eboot.nb0
3. We copy on miniSD in a root directory.
4. We insert miniSD in Pocket, enter in bootloader (Camera+SR)
5. We wait inundated while.
6. We take out a miniSD, enter in bootloader, start sewing on PC, connect to USB (it is needed to put to death in the processes of AS)
We are sewn!!!
Hey friens and developers,
I have read the information in post " dead hermes? corrupted radio? Post comments here" and follow the instruction "Device is stuck in bootloader mode".
My problem is, I can´t get a connection to my device (mtty), I have on 4 different PCs (XP or Vista Operation System) every time the same information --> "USB Port can´t not open".
My Question is, is the Bootloader damage ?
History:
The hermes are function well and I get yesterday a problem with frozen the Device. I solve the problem and do a hard reset, but after Installation the Device boot and stay now in the HTC Screen. (Look attachment). If i hardreset the device a see the tri-color Boot-Picture for a 0,5 sec, but no numbers.
THX for some idea´s
Thomas
Did you read the Wiki page for unbricking the Hermes?
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Yes I do, but I have the Problem with the USB Connection (mtty). You have any Idea for the USB Problem?
The Hermes now is function with USB. I install a new XP with SP2 on my PC and I have a connection.
Now I see the BOOTLOADER
HERM200
IPL-1.04
Herm200
SPL 2.-03
I want to flash the Device, but every Solution STOPT by 1%, "the image file is corrupted". Any Idea how to change the Bootloader to a compatibility Bootloader over mtty?
What ROM you trying to flash? It has to be a Hermes ROM or you're gonna end up with a permanent brick.
Have you installed Hard SPL V7? If you have you can use the sd card method to install the ROM.
If its a Hermes ROM and you keep getting the "the image file is corrupted" message, good, it means you won't have a brick at the end as the file is corrupted and could result in a brick. Either download the ROM image again or download something else. That error message is there to save your Hermes from brickage.
Cheers...
Hi,
I'm having problems with my niki100. When I power it up, it stucks in the second screen with the red letters at the bottom giving the radio version and other data.
The problem started after flashing a new rom:
PTG cleanblack wm 6.5 "showthread.php?t=689898"
Before installing this rom I was tring the ROM from Dj_series VA11, but there were some problems to get the phone to work, it was going to offline mode not setting up the connection to the mobile operator. Befrore changing any rom I've done the hardspl 1.22.
Now it's not working, I've done a hardreset, but it's the same, I can´t get active sync to work in order to do some flashing, I tried to enter to bootloader pressing camera and power button, the 3 color menu says USB when connecting the usb cable but on the labtop theres no port associated in device manager and no possible communication between niki and PC.
Any help would be thankfull..
Problem solved !
I've tried to flash it again through sd card with the same rom and the problem remain. After that I've changed the image on the sd card to the previous version (Dj series) , renamed the image on sd, camera*rst* and power button simultaneous, flash from sd and it went ok.
It's working now !
Thanks anyway
hello
can you please help me, my dual is on the same status as yours but i dont have SD :s but he goes to Bootloader and when i try to update erro ID Vendor, if i try to HDspl ou sspl the same erro..
can anyone help please..