Hello,
my Herm200 isn´t booting anymore. I see the CRC- Release splash-Screen and nothing more. when trying to flash a new rom, my pda stops at 1%.
When i try to flash from SD, i get the 00068002 error.
What can be done else to get the system back to work ? i tried several roms and bootloaders without success.
bootloader is spl-1.11.
Thanks in Advance
Pure_y2k
I get the same error on my HTC MTeoR (Breeze) with SPL-1.07.0000 when the bootloader tries to find the rom update (BREEIMG.NBH in the root of a FAT32 micro-SD). Please help me too...
I can't believe that it's not possible to update via the sd card.
Sorry for my poor english...
TIA. Giovanni
gio91ber, you'd probably get more help on the Breeze forum. Someone there may have figured out and posted a version of the Hermes Hard SPL for your type of mobile...
Cheers...
pure_y2k, you need to have Hard SPL ver7 installed to use the sd card method. Please refer to page 116, post 1160 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
This will put Hard SPL on your Hermes with sd card method. READ THIS CAREFULLY asi it contain an extra couple of steps...
Cheers...
Related
Hi all,
i've found an alternative approach to flash any firmware on HERMES 200.
I had a problem while i was trying to upgrade my WM5 Vodafone 1605 to WM6.
My bootloader is SPL-1.09, and i've tried in many ways to install Hard-spl v7 but here is what was keeping happening:
- I try to flash my Hermes with hardSPL v7 and each time:
- Hermes switch to bootloader mode and display
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
- Activesync lose the connection
- Windows XP send popup with new USB device and ask me to install the new device (no idea of driver not found by default)
- RUUWrapper display error 260
Click to expand...
Click to collapse
Here is the solution:
- Download the firmware u wish to install on your device
- Unpack the firmware (right-click and Extract)
- copy the .nbh file into you microSD card and rename it as: HERMIMG.nbh
- put SSPL-HERM.exe into you device (you can get this app in this site too)
- now put you microSD card into you device and run SSPL-HERM.exe
- enjoy
I'm just an unexpert user that has tried many times to upgrade his device reading other posts on this forum. So pls correct me if i've said something wrong!
I wrote this post just cause i was going crazy and i wasn't able to find a solution like this around the sites
Hope this help somebody!
PS: I'm sorry for my bad english!
RUUWrapper display error 260? try to disable your firewall, flash again, and you will see it works.
regards chief
i've got the same problem with my hermes...
i don't know how to fix...when i start the flashing process the device switches in the bootloader mode and then nothing else is happening, there is no connection to the pc. i tried to switch off the firewall, i changed the cable, i changed usb port but nothing happens...
does anybody know what i shall do?
its the same fault as anvillani describes, the only thing different is that i dont get herm200 but herm300
Do you guys do ANY research before trying this???
Go to this thread - http://forum.xda-developers.com/showthread.php?t=296722
Go to page 116, post 1160 and READ it step by step, juymp ahead and this WON'T work. Just make sure you use a 2Gb or less sd card. INSTALL HARD SPL 1st.... Then you can use the sd card method (just skip the steps using sspl.exe as you should now have Hard SPL) to update your roms....
Cheers...
i really dont know what you want to say with this...
i tried the normal procedure to flash hard spl to my device and i tried the method anvillani suggested and both didn't funtion.
so my question is what i should do...
Follow the link and instructions in my previous post. It will allow you to install Hard SPL using the sd card method. You do need to be able to get to the today screen though.
After reading anvillani's post I'll add that the sd card MUST be 2Gb or less and has to be formatted FAT32. You have to name the .nbh file hermimg.nbh with NO speeling (sorry, spelling :b) errors or it won't work.
Cheers...
My Htc hermes phone keep turning off and on after i upgraded it to rom 3.54.07.06. that i downloaded from a thread on this site. I did the Power+OK+softrest and got the 3 color screen its shows IPL 1.01 and SPL 1.40 Oilpro . and connected to my computer but my computer isnt snycing withmy phone or anything plz help me T~T
Welcome to XDA-developers.
The Hermes has a wonderful Wiki page for unbricking a device:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
You can also try to flash from the SD Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Though I'd try to upgrade the SPL(1.40) to Hard SPL V7 (2.10) first.
Try connecting the Hermes to the pc after 1st making sure to untick "Allow USB connections" in activesync, put the Hermes in bootloader and run the RUU_Wrapper.exe for Hard SPL V7. After this you should be able to use the sd card method to flash your Hermes with any rom. You used an early Hard SPL that is unsafe to try sd card flashing with... Live and learn...
Thanks very much your a life saver
i did it too
dear
yesterday i flash my hermes with hardspl v7
i get
HERM100
ipl 1.04
spl 2.10olipro
but i can"t flash original rom from sd card it only stuck at 0%
i try to unbrick my hermes because i get no radio and no gsm missing protocol and missing my imei
what kind of solution for me????
please help
SD card flash....
1. Format 2Gb or less card FAT32. Copy .nbh file onto it and rename hermimg.nbh.
2. Insert sd card into Hermes and reset to bootloader.
3. Follow prompts...
If you are using the unaltered ROM, the radio part may take awhile to flash - DON'T RESET... This may cause irrecoverable errors in the radio rom causing you to have a permanent brick...
Cheers...
This may not work, that means you're looking at a permanent brick. You may be able to flash an OS only rom on but you won't be able to use the phone anymore.
hi everybody...i'm new on this forum and i don't have any experience with flashing roms...i have a Hermes with windows mobile 6 that doesn't want to go along with the upgrades(SPL for start).I read a lot of tutorials but no luck..booted the phone in bootloader mode:
HERM300
IPL-1.01
HERM300
SPL-1.40.Olipro
i'm not the first owner of the phone...it runs well but i'd like to put wm 6.1 on it.
i have tried to hard spl, my phone resets in bootloader mode...the pc recognizes it but after 2-3 minutes it gives me an error( error 260)...
I am currently using windows vista ultimate 32-bit...please give me a hand guys...thanks in advance
please start reading here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
best way to flash is from the SD Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
thanks alot for the response but i am aware of the procedure...i was thinking of trying to flash the rom directly without hard spl...i know it's not recommended...if someone could help me with the error i get i'l apreciate it...
just wondering...could i flash a windows mobile 6.1 rom using the sd card method without doing hard spl (using the spl i have now: 1.40 Olipro) ?
w3b3r said:
thanks alot for the response but i am aware of the procedure...i was thinking of trying to flash the rom directly without hard spl...i know it's not recommended...if someone could help me with the error i get i'l apreciate it...
just wondering...could i flash a windows mobile 6.1 rom using the sd card method without doing hard spl (using the spl i have now: 1.40 Olipro) ?
Click to expand...
Click to collapse
for the SD card method you need HardSPL v7... you will have to flash it... not much else anyone could do with it.
thanks for the posts guys..from my last post i've flashed a f ew roms on my hermes without any problems..istil have spl 1.40..i guess the risk of bricking my device is bigger..i'm now lookIng for a clean 6.1 rom..without any preinstalled aps and crap i dont use...a recommandation would be nice
Hi,
My herm 200 ,swisscom, has IPL1.01 and SPL 1.4Olipro. But always when I try to install Hardspl v7 it give me error 262 and only 0%.
Can someoone help me what to do because I want to flash new rom and new radio rom trough my SD card.
Thnx
i would suggest reading this wiki page which might help you with that error. A recent thread that had a error with flashing hard spl here may help you although it is for a different error, you may still get some ideas on how to fix it.
Hope this helps and Good luck
I did read everything but with no success. always error 262. I have Win XP SP3 with framework 3.5 but I dont think that would be a problem for this error.
Have you tried putting the Free HTC Hermes SIM & CID unlocker on your hermes as this may be the problem or have you tried flashing it using the sd card method.
Go to page 116, post 1160 of this thread - http://forum.xda-developers.com/showthread.php?t=296722 . It will tell you how and supply ALL the apps so you can use the sd card... Easier and safer...
Cheers...
is it the same procedure to put a new OS Rom through the SD card? After flashing to Hardspl v7.
P.S. it is super CID because I checked with mtty.
Hi Guys
I need your help right now...
It's my first time I'm trying to flash my MDA VARIO II form WM 5 to WM 6.
I found this ROM here in the Board:
http://forum.xda-developers.com/showthread.php?t=359917&highlight=Shamanix_WM6_Ultimate_v2_FINAL
I also installed HardSPL 7 Using this guide:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
And now I want to install the new ROM Using this Guide and the File above:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=17&Itemid=26
But when I click Autodetect it says: Error! Unknown Version.
Sorry for asking so stupid questions but i am a bit confused right now and I really don't want to crash my phone, this would be a mess....
Can Anybody Help me?
And is there Anything else to look after? I read something about CID unlock in the wiki, is this done by installing HardSPL?
ty so far
DasEtwas
First i would suggest reading the wiki pages as you may find something that could help, also it may not be detecting it as you do need to press accept or yes to run something on your hermes. although if it doesnt detect it you can see what spl you are running (press ok, power and reset button together) from there you can select what version you have on your devise it will also check whether hard-spl worked.
Hope this helps and good luck
Hard SPL is installed and I read the wiki, but I don't get behind the CID^^
The question is: Is this ROM Above comaptible to my MDA Vario? And anyway what is this CID?
Ty so far
DasEtwas
If you downloaded it from the Hermes section then yes...
As you have Hard SPL V7(?) (check if SPL is 2.10 oli), try the sd card method...
1. Format sd card FAT32. Copy .nbh file to it and rename to hermimg.nbh .
2. Insert sd card into Hermes and reset to bootloader, Scotty93 told you how.
3. Follow the prompts...
Easy...
Yes I installed Hard SPL V7 and in the bootloader it says SPL 2.10 olipro.
I will try the method now *Wish me good luck*
ty so far
DasEtwas
Edit:
Hm i don't have an Adapter for the Micro SD Card, is it possible to copy the nbh File onto the Card using Active Sync, while it's in the Phone?
Edit: Hm n1 one I tried to formate my SD Card (Yeah I found the Adapter) but windows had an Error and now it hangs up everytime I try to access the card....